AMERICAN LIGHTING CTRL-DMXB-RGBTW-4Z Intelligent Touch Panel Instruction Manual
- June 4, 2024
- American Lighting
Table of Contents
AMERICAN LIGHTING CTRL-DMXB-RGBTW-4Z Intelligent Touch Panel
Product Introduction
The IntelligentTouchPanel is an Americanbase wall switch,integrating Bluetooth5.0 SIG Mesh and DMX signals.It is a simple but elegant design with CNC aviation aluminum frame and 2.5D tempered glass. The panel is suitable for multi-scene and multi-zone lighting control applications. Working with Bluetooth systems makes it more convenient and intelligent.
Technical Specs
| Model | CTRLW-DMXB-TW-4Z | CTRLW-DMXB-RGBW-4Z | CTRLW-DMXB-RGBTW-4Z |
|---|---|---|---|
| Control mode | TW | RGBW | RGBTW |
| Input voltage | 12-24VDC, Powered by Class 2 | ||
| Wireless protocol type | Bluetooth 5.0 SIG Mesh | ||
| Output signal | DMX 512 | ||
| Zones | 4 | ||
| Working temperature | -20°C~55°C | ||
| Dimensions(L×W×H) | 120×75×30(mm) | ||
| Package size(L×W×H) | 158×113×62(mm) | ||
| Weight(G.W.) | 225g |
Product Size
Key Functions
TW
RGBW
RGBTW
DMX Application Diagram
Each zone can be installed with multiple decoders. When the total number of decoders in 4 zones exceeds 32, please add DMX signal amplifiers.
Warning
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interferenceto radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF exposure guidelines, the distance must be at least 20cm between the radiator and your body, and fully supported by the operating and installation configurations of the transmitter and its antenna(s).
This manual is subject to changes without further notice. Product functions depend on the goods. Please feel free to contact our official distributors if you have any question.
DMX Channel Output Sheet
Types
Addresses Zones
| TW| RGBW| RGBTW
---|---|---|---
CT1| CT2
1| C1| BRT1| R1| R1
2| W1| CT1| G1| G1
3| C2| BRT2| B1| B1
4| W2| CT2| W1| BRT1
5| C3| BRT3| R2| CT1
6| W3| CT3| G2| R2
7| C4| BRT4| B2| G2
8| W4| CT4| W2| B2
9| C1| BRT1| R3| BRT2
10| W1| CT1| G3| CT2
11| C2| BRT2| B3| R3
12| W2| CT2| W3| G3
13| C3| BRT3| R4| B3
14| W3| CT3| G4| BRT3
15| C4| BRT4| B4| CT3
16| W4| CT4| W4| R4
17| C1| BRT1| R1| G4
18| W1| CT1| G1| B4
19| C2| BRT2| B1| BRT4
20| W2| CT2| W1| CT4
…| …| …| …| …
500| W2| CT2| W1| CT4
…| …| …| …| /
512| W4| CT4| W4| /
- Every 8 addresses of CT1 and CT2 are circulated in 4 zones, every 16 RGBW addresses are circulated in 4 zones, every 20 RGBTW addresses are circulated in 4 zones.
Installation Instructions
Step 1: Remove the panel plate with a flathead screwdriver, as shown
below.
Step 2: Attach the wires to the panel, as shown in the diagram below .
Please be sureto turn off the power to the circuit at the circuit breaker or
fuse box before attaching the wires.
Step 3: Install the panel plate. Once the wires are attached correctly,
you can gently fold any excess wire and compress the panel into the junction
box. Tighten the screws to secure the panel plate to the box.
Step 4: Put the panel cover in place. Gently snap the panel cover onto
the plate.
Attentions
- Please use in spacious and open space. Avoid metal obstructions above and in front of products.
- Please use in a cool and dry environment.
- No disassembly of products so as not to affect the warranty.
- Avoid direct contact with light and heat.
- Please do not open, modify, repair or maintain products without authorization, otherwise warranties are not allowed.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>