ESR 2B513 15W Car Charger with MagSafe and CryoBoost Instruction Manual
- June 12, 2024
- ESR
Table of Contents
ESR 2B513 15W Car Charger with MagSafe and CryoBoost Instruction Manual
Product Overview
- MagSafe charging pad
- CryoBoost status light & vent
- USB-C port
- Air vent mount 5. CryoBoost intake
Status Light and Cooling Fan Guide
Charger Status| Power on| Standby| Charging| Fully
charged| Error detected
---|---|---|---|---|---
Light| On| On| Slow pulsing| On| On
Fan| Low speed for 3 seconds then off| Off| High speed| Off| Stops
If charging stops or an error is detected:
- Ensure that your phone supports wireless charging and that there are no credit cards, stands, or other attachments on the back that will interfere with charging.
- After checking the above, unplug and plug in the charging cable again to resume normal charging. (X
Important Reminders
- This charger will only attach to caseless iPhones with MagSafe (12 series or later), official MagSafe cases, ESR HaloLock cases, or standard cases with a HaloLock Universal Ring. It may not attach to other magnetic cases. It will not attach to any other non-magnetic phones or cases.
- This charger supports an input of 9V-3A and outputs a maximum of 15W.
- For maximum charging speed, use included cable.
- The charger must be connected to a power source to begin wireless charging.
Safety Warnings
- Do not expose the device to temperatures below 0°C (32°F) or above 60°C (140°F).
- Do not expose the device to an open flame or submerge it in water as this will damage the device.
- Always check for damage to the device, cables, or other accessories before using the device. If damaged, do not use the device.
- Do not attempt to disassemble or modify the device in any way as this will void the warranty, may cause damage, and the components may be swallowed by young children.
- Do not expose the device to corrosive liquids or high humidity as these will seriously damage the device and void the warranty.
Installation Instructions
FCC ID: 2APEW- 2B513
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1 ) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator &your body.
This product complies with the radio interference requirements of the European Community.
IC: 24790- 2B513
This device complies with Industry Canada
licence-exempt RSS standard( s). Operation is subject to the following two
conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.”
This equipment complies with IC RF radiation exposure limits set forth for an
uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 10
centimeters between the radiator and your body.
Declaration of Conformity
This product is intended for use within Europe. Electronic Silk Road Corp. hereby declares that this product 2B513 is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU,2014/35/EU,2014/30/EU. The Declaration of Conformity for the 2B513 is available from www.esrgear.com
This symbol indicates that this product shall not be treated as household waste.lnstead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.
Scan to watch a quick setup video
esrgear.com/faq/2b513
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>