ESR 2C522D Magnetic Wireless Car Charger User Manual

ESR 2C522D Magnetic Wireless Car Charger

INSTALLATION INSTRUCTION

OVERVIEW

1. Wireless charging pad
2. USB-C port
3. Heat vents
4. Status lights
5. Mount

Status Light Guide

If an error is detected:

1. Credit cards, stands, or other attachments on the back will also interfere with charging.
2. After checking the above, unplug and plug in the charging cable again to resume normal charging.

Important Reminders

1. The charger only supports magnetic attachment with a caseless iPhone with MagSafe, an official MagSafe case, an ESR HaloLock™ case, or a standard case with a HaloLock™ Universal Ring. It may not attach to other magnetic cases. It will not attach to any other non-magnetic phones or cases. (Over time, the charger may leave a faint circular mark on the back of your phone that can be easily cleaned with an alcohol wipe.)
2. The charger supports an input of 9V=2A and a maximum output of 10W. The maximum output supported by an iPhone is 7.5W.
3. Only use the cable provided with the charger. An Apple cable or other third-party cable may interfere with charging.
4. This charger requires a charging adapter that supports QC or PD fast charging and an output of at least 18W.
5. The charger must be connected to a power source to begin wireless charging.

Safety Warnings

1. Do not place the device in temperatures below 0°C (32°F) or above 60°C (140°F).
2. Do not attempt to disassemble the device, expose it to an open flame, or submerge it in water to avoid damaging the device.
3. Always check for damage to the device, cables, or other accessories before using the device. If damaged, do not use the device.
4. Do not attempt to disassemble or modify the device in any way, as may cause serious damage and void the warranty.
5. Do not expose the device to extremely hot, humid, or corrosive environments to avoid damaging the device.

FCC

ID: 2APEW- 2C522D

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference,
2. this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur during a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator &your body.

IC: 24790-2C522D
This device complies with Industry Canada license-exempt RSS standard( s). Operation is subject to the following two conditions:

1. this device may not cause interference
2. this device must accept any interference, including interference that may cause undesired operation of the device.’

This equipment complies with IC RF radiation exposure limits set forth for an uncontrolled environment
This equipment should be installed and operated with a minimum distance of 10 centimeters between the radiator and your body
This product complies with the radio interference requirements of the European Community.
EN Declaration of Conformity
This product is intended for use within Europe. Electronic Silk Road Corp. hereby declares that this product 2C522D is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU,2014/35/EU,2014/30/EU. The Declaration of Conformity for the 2C522D is available from www.esrgear.com
This symbol indicates that this product shall not be treated as household waste. Instead, it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.
Scan to watch a quick setup video

Documents / Resources

| ESR 2C522D Magnetic Wireless Car Charger [pdf] User Manual
2APEW-2C522D, 2APEW2C522D, 2C522D, 2C522D Magnetic Wireless Car Charger, Magnetic Wireless Car Charger, Wireless Car Charger, Car Charger
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>