Berker 29518982 LED Signal Light Instruction Manual

: June 12, 2024
: Berker

Table of Contents

Safety instructions
Function
Operation
Information for electricians
Appendix
Warranty
Documents / Resources

Operating and
assembly instructions

2951 xx xx
LED signal light, RGB
2952 xx xx
LED signal light, red/green
lighting
2953 xx xx
LED signal light, white lighting

Safety instructions

Electrical equipment may only be installed and assembled by a qualified electrician in accordance with the relevant installation standards, guidelines, regulations, directives, safety and accident prevention regulations of the country.
Hazard due to electric shock. Disconnect before working on the device.
Take into account all circuit breakers that supply dangerous voltages to the device.
Failure to comply with these instructions may result in damage to the device, fire, or other hazards.
Device is not suitable for use in safety technology or as emergency light.
Hazard of fire. Do not operate device on a dimmer. The lamps are not dimmable.
If several devices are to be connected via the contact operating modes, it is absolutely essential that all devices are operated via the same phase. Otherwise devices may be destroyed.
Do not operate device on an electronic switch insert (e.g. Tronic or Triac insert). The switch insert may be damaged.
These instructions are an integral component of the product and must be retained by the end user.
Design and layout of the device

LED signal light
Design frame (not within scope of delivery)
Printed foils (optional, see accessories)
Hood
Centre plate
Potentiometer for brightness (not with LED signal light, red/green lighting)

Function

Correct use
– LED light for signalling e.g. notices, information, messages or warnings
– Operation via separate push-button or switch
– Installation in switch combinations or individual
– Installation into wall box according to DIN 49073

Product characteristics
Owing to manufacturing tolerances in LED production, noticeable differences in brightness and color reproduction are possible.

LED signal light, red/green lighting
– Two-coloured signal light, e.g. for access control
– Switchable between red and green via separate switches
– Two coloured foils with imprinted symbols for Do not disturb/Clean room and Please enter/ Please wait are supplied

LED signal light, RGB
– LED light for signalling notices, information or warnings
– The colour is switchable via an external pushbutton
– Foils with imprint of symbols insertable (see Accessories)
– Light colours cold white, warm white, blue, orange, red, green, purple (magenta) and colour sequence callable via push-button
– Brightness modifiable via potentiometer
– Colour sequence can be stopped at any position via the push-button

LED signal light, white lighting
– LED light for signalling notices, information or warnings
– Switchable via separate switch
– Foils with imprint of symbols insertable
– Light colour cold white
– Brightness modifiable via potentiometer

Operation

LED signal light, red/green switch lighting
The colours red and green can be switched or changed over individually using a series switch or change-over switch.

Press switch.
The LED signal light switches to red, green or off.

LED signal light, switch white lighting
The LED signal light can be switched using an Off/ changeover switch.

Press Off/changeover switch.
The LED signal light lights up cold white or is switched off.

LED signal light, switch RGB
The LED signal light is switched on/off using a switch or switching contact.
The LED signal light is switched off.

Press on/off switch.
The LED signal light lights up white for a short time and then switches to the colour prior to switching off the last time or starts the colour sequence.

The colour sequence always starts with purple (magenta).

Operation of LED signal light, RGB
Setting colour
The colour of the LED signal light is set with a separate, additional push- button.
With each press of the push-button, the colour sequence is switched by one colour state, in the sequence:
– cold white
– warm white
– blue
– orange
– red
– green
– purple (magenta)
– Colour sequence
– stopped colour sequence

The LED signal light is switched on.

Press push-button for a short time.
The LED light changes to the next colour.
Keep pressing the push-button until the required colour or colour sequence are active.

Setting the colour via the colour sequence
The colour of the LED light can also be adjusted via the colour sequence.
The entire colour sequence lasts about 5 minutes.
The colour sequence is active.

During the colour sequence, press the pushbutton for a short time at any position.
The colour sequence stops.
The colour currently displayed is set.

The colour will remain stored even after a voltage interruption.
To restart the colour sequence, select the colour sequence again with the push-button.

LED signal light, synchronise RGB
If several LED signal lights are operated RGB in parallel, it is possible that the LED lights may not light up in the same colour or the colour sequence may run asynchronously after switching. In this case, all LED lights can be reset.

Keep the push-button pressed for more than 2.5 seconds.
The LED signal lights run through a reset and are switched off.
Release push-button.
The LED signal lights light up white. The delivery condition is restored.

Information for electricians

Installation and electrical connection
DANGER!
Electrical shock when live parts are touched.
An electric shock can be lethal.
Disconnect the connecting cables before working on the device and cover all live parts in the area!
CAUTION!
Fire hazard if the neutral conductor is looped through.
Do not loop neutral conductor through to other devices.
Connecting and installing the device

LED signal light, white lighting

Wire LED signal light with Off/changeover switch (7) (Figure 2).
Install insert (8) into a wall box. The connecting terminals must be at the bottom.
Complete the LED signal light (Figure 1)
Position the frame (2) over the supporting ring of the insert (1)
Place a foil (3) under the cover if necessary
Push the cover (4) onto the insert until it engages
Snap on centre plate (5)
Switch on mains voltage

Figure 2: Connection example of LED signal light, white lighting

(7) Off/changeover switch
(8) Insert of LED signal light, white lighting

LED signal light, red/green lighting

Connect LED signal light according to connection example (Figure 3). Instead of the series switch (9) that should switch both colours separately, a change-over switch that merely enables a change-over of both colours can also be used:
Lrd= Activation of the colour red,
Lgn= Activation of the colour green
Install insert (10) into a wall box. The connecting terminals must be at the bottom.
Complete the LED signal light (Figure 1).
Position the frame (2) over the supporting ring of the insert (1).
Place a foil (3) under the cover if necessary.
Push the cover (4) onto the insert until it engages.
Snap on centre plate (5).
Switch on mains voltage.

Figure 3: Connection example of LED signal light, red/green lighting

(9) Series switch
(10) Insert of LED signal light, red/green lighting, N terminals bridged

LED signal light, RGB
The following example circuits show two possibilities for connecting the LED orientation light. In the connection example (Figure 4), the neutral conductor is pressed onto control input „1“ in order to switch over the colour. In the connection example (Figure 5), the outer conductor is pressed onto the control input „1“.

Figure 5: Connection example of colour switching via outer conductor, not looped

(11) Off/changeover switch
(12) Push-button
(13) Insert of LED signal light, RGB
(14) Connection possibility of additional LED signal lights, RGB

CAUTION!
Fire hazard if the device is connected to DC voltage.
Only connect to AC voltage 230 V~, 50 Hz.

Connect LED signal light, RGB according to connection example (Figure 4) or (Figure 5).
Connect additional LED signal lights, RGB via (14).
Install insert (13) into a wall box. The connecting terminals must be at the bottom.
Complete the LED signal light (Figure 1).
Position the frame (2) over the supporting ring of the insert (1).
Place a foil (3) under the cover if necessary.
Push the cover (4) onto the insert until it engages.
Snap on centre plate (5).

Changing brightness of the LED signal light In delivery condition, the potentiometer (6) is set to maximum brightness.

Switch off mains voltage.
Pull off centre plate (5) from the supporting ring.
Remove frame (2).
Remove supporting ring from the flush-mounted box.
Pull out insert (1) from the flush-mounted box.
Set potentiometer (6) (Figure 6).
Reinsert the insert into the flush-mounted box and screw tightly over the supporting ring.
Position the frame (2) over the supporting ring of the insert (6).
Snap on centre plate (5).
Switch on mains voltage.

Appendix

Technical data

Rated voltage	230 V~
Mains frequency	50/60 Hz
Number of LEDs	4
Connection single stranded	2.5 mm²
Ambient temperature	-15 … 40 °C

LED signal light, order no. 2951 xx xx

Power consumption	max. 2 W at 195 … 265 V~, 50/60 Hz
Power factor	approx. 0.9

LED signal light, order no. 2953 xx xx

Power consumption	per colour max. 0.5 W at 230 V~, 50 Hz

LED signal light, order no. 2953 xx xx

Power consumption	max. 1 W at 230 V~, 50 Hz
Power factor	approx. 0.17

Accessories

for red/green LED lights:
Foil bi-color with imprint : 1905801x
for RGB and white LED lights:
Foil with imprint : 1905800x

Warranty

We reserve the right to make technical and formal changes to the product in the interest of technical progress.
Our products are under guarantee within the scope of the statutory provisions.
If you have a warranty claim, please contact the point of sale or ship the device postage free with a description of the fault to the appropriate regional representative.

Berker GmbH & Co. KG – Zum Gunterstal
66440 Blieskastel/Germany
Tel.: + 49 6842 945 0
Fax: + 49 6842 945 4625
E-Mail:info@berker.de
www.berker.com
6LE000851B – 12/2020