Enjoy AJ1188 Fire Pit Table Instruction Manual

Fire Pit Table
Owner’s Instruction manual SKU No.:
AJ1188

AJ1188 Fire Pit Table

WARNING: FOR OUTDOOR USE ONLY ATTENTION: READ INSTRUCTIONS CAREFULLY BEFORE ASSEMBLY OR USE INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE. CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.
5010198 Design certified under ANSI Z21.97:2017/CSA 2.41-2017 Standard for Outdoor Decorative Gas Appliances

Warnings

DANGER
CARBON MONOXIDE HAZARD

• This appliance can produce carbon monoxide which has no odor. Using it in an enclosed space can kill you.
• For outdoor use only.
• Never use in the unventilated or enclosed areas.

IF YOU SMELL GAS:

• Shut off gas to the appliance.
• Extinguish any open flame.
• If odor continues, keep away from the appliance and immediately call your gas supplier or fire department for help.

WARNING

• WARNING indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. An LPcylinder not connected for use shall not be stored in the vicinity of this or any other appliance.

WARNING

• If the propane gas tank is leaking gas, you may hear, see, or smell a hiss. Do the following:
  1. Disconnect the propane gas tank.
  2. Do not attempt to fix the problem by yourself.
  3. Contact your gas supplier or fire department for help.

• Do not use a flame to check for gas leaks.

• Keep gas tank at least 5 ft away from unit when lit. (if external tank)

• The maximum gas supply pressure is 250psi.

WARNING

• Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage.
• Read the owners manual thoroughly before installing or servicing this equipment. If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury, or loss of life.

WARNING

• The installation of this unit must adhere to local codes or either the National Fuel Gas Code, ANSI Z223. 1/NFPA54, OR CAN/CGA- B149.1, National Gas and Propane Installation Code.
• This unit is to be used with propane gas only! (sold separately), is not intended for natural gas.
• Do not use any solid fuel or charcoal for this unit.
• Do not use any more than 1/4in depth lava rocks/ pumice stones/ Lava Glass above the burner holes. Doing so will suffocate the flame.

WARNING

• Applying too much propane may result in gas pooling and will not burn.
  Allow fresh air into the unit so that the remaining gas may escape.

• Use LP propane tanks with the following dimensions: diameter 12inch, height 18inch, capacity 20lbs.

• You must use a propane tank that has a collar to protect the gas valve.

• DO NOT fill tank over 80 Percent full.

• The LP gas tank must have a listed overfilling prevention device and a QCCI or Type I, (CGA810) LP gas tank connection.

• The gas supply tank should be constructed and marked with the specifications for the LP gas tanks of the U.S. Department of Transportation or the National Standard of Canada CAN/CSA-B339, LP gas tanks, spheres and tubes for Transportation of Dangerous Goods and Commission.

• Discontinue use if any part of the propane tank is damaged. Rust and dents may be hazardous and should be inspected by a gas supplier.

WARNING

• DO NOT add water into the unit.
• DO NOT disconnect any part while the unit is in use.
• DO NOT operate on a boat or vehicle.
• DO NOT set the Protective Cover over the unit until the Fire Table / Column is turned off and completely cooled down (where applicable).
• Check for leaks after not using the unit for long periods of time.

WARNING

• All installation and repair should be done by a Qualified Service Technician. This unit should be inspected annually and cleaned regularly.
• Inspect all elements of this Fire Table / Column before each use.
• If there is damage, the Burner must be replaced.
• The LP Gas tank must have a listed overfilling prevention device and a QCCI or Type I, LP Gas tank connection.
• Use only the Regulator (19) and Hose (12) assembly provided with this unit.
• If the Burner (06) shows any kind of damage, DO NOT operate the appliance.
• This heating appliance should NOT be used on plastic, artificial wood desks or any desk.

WARNING

• Do not operate unit until all parts are fully assembled.
• Do not attempt to move it while in use.
• This unit is not intended for cooking.
• Young children should be carefully supervised when they are in the area of the appliance.
• Keep away from the unit for the first 20 minutes after igniting for the first time, as lava rock /pumice stones could pop out and cause injury.
• Do not set the protective cover over the unit until it is turned off and completely cooled down.
• Combustible material should not be within 72 inches of the top of the unit, or within 48 inches around the entire unit.
• If the flame goes out while burning, turn the gas valve off. Wait 5 minutes before repeating the initial lighting procedure. Once you have a flame started, hold down the control knob for 1 minute.

WARNING

• Inspect all elements of this heating unit before each use. If there is damage, the burner must be replaced.

• Keep the hose out from any pathways to eliminate any accidental damage. (if external tank)

• Installation and repair should be done by a qualified service person.
  The appliance should be inspected before use and at least annually by a qualified service person. More frequent cleaning may be required as necessary.

• You must follow all steps to properly assemble this heating item. Make sure the gas valve is turned “OFF” before assembling. Do NOT attempt to assemble without proper tools.

Parts Diagram

Tabulated here below are the description to all parts as shown in above Picture .

Parts List

pcs
W002| M6 Washer| 12 pcs
T001| Hex Bolt Driver| 1 pc
S001| Bolt (M6*16MM)| pcs

Assembly Instructions

Step 1: Check the control knob for gas supply system is turned to OFF position before starting your assembly. Step 2: Attach panel (G) 2pc to the table top (E) by using 4pcs of Bolts(S003) and 4pcs M6 washer(W002) with Hex Bolt Driyer(T001). Please do not fully tighten.

Step 3:
Attach panel (F) with Panel (G ) and Panel (H ) together by using 8pcs Bolts(S004) and 8pcs M6 washer(W002) with Hex Bolt Driver(T001). Please do not fully tighten.

Step 4:
Attach foot pad (I) to the bottom of fire pit using 8pcs of Bolts (S001) with Hex Bolt Driver (T001). And tighten the Bolts.

Step 5:
Put the metal lid on the table top of fire pit. Then tighten all the bolts.

User’s Instructions

Step 1:

1. Check that the Control Knob for the gas supply system is turned to the “OFF” position before starting any assembly.
2. Place a 20 lb Propane Gas Tank (not included) into a secure position.

Step 2:
Turn the Cylinder Valve on the tank in a clockwise direction to TURN OFF SUPPLEY of the LP Gas supply-Attach the preassembled Regulator (19) from the Fire Table to the Cylinder Valve (21) by turning the Black Regulator Coupling Nut clockwise. Make sure it is fastened securely and tighten connections-by HAND only.

Step 3: Remove the Electronic Igniter Cap on the Electronic Igniter by unsecrewing and slide the Battery (B) into the battery slot. Make sure the positive side of the Battery faces outwards. Screw the Electronic Igniter Cap over the battery, tightly. Step 4: Put Glass Rocks over the Burner Ring. Warning: DO NOT PLACE GLASS ROCKS ON THE GUARD. KEEP GUARD CLEAN. To ensure proper function, the Guard (01) on the Burner (06) should never have glass rocks ( 0 ) covered over it.

SAFETY INFORMATION

Only use the regulator and hose assembly provided with this unit. Replacement parts must be supplied directly by us.
Inspect the burner before use of this unit. If the burner shows any kind of damage, do not operate the appliance.
NOTE: You must follow all steps to properly assemble this heating item. Make sure the gas valve is turned “OFF” before assembling. Do NOT attempt to assemble without proper tools.

The gas tank should be placed outside the fire pit table

Operation

FOR YOUR SAFETY, READ BEFORE LIGHTING

• Before performing a leak test, make sure that no sparks can occur and you are in a spacious outdoor area.
• Connect the propane gas tank to the regulator and turn the valve on the unit to the “off” position.
• Brush a soap and water mixture on all connections.
• Make sure the igniter battery has been installed properly. The igniter will not operate otherwise.
• Before operating, smell around the appliance and next to the ground for gas odors. If you smell gas or a leak is discovered turn the gas valve off, disconnect propane gas tank and do not use the appliance until the leak is repaired.
• If there are signs of wear or abrasion on the hose, you must replace the Gas Hose. And the Gas Hose must be supplied directly by manufacturer.
• Stand away from the Fire Table / Column for the initial 20 minutes after igniting.
• Lava rocks / pumice stones could pop up and strike somebody’s face during the process of lighting this unit.
• Pumice stones/lava rocks/Lava Glass could pop up and strike somebody’s face during the process of lighting this unit; Wait 10 minutes after extinguishing flame prior to replacing a lid (if applicable) or protective cover onto the Are Table.

To Light

1. Make sure the control knob is in the “OFF” position.
2. Slowly open the valve on the propane gas tank by turning the knob counterclockwise.
3. Push and hold in the electronic ignitor to create sparks within the electrode, continue to hold.
4. Push in the control knob and turn to the”HIGH” position. Keep holding down the control knob to allow gas to fow for 10-15 seconds.
5. If ignition doesn’t occur within a few seconds release the control knob and rotate to the”OFF” position. Wait for 5 minutes for gas to clear and then repeat the above lighting instructions.
6. Once the fire is lit, the flame intensity may be controlled by turning the control knob between the”LOW”and “HIGH” positions.

To Extinguish

1. Close the cylinder valve on the propane gas tank if you don’t intend to use it for a long time.
2. Turn control knob clockwise to the “HIGH’ position; let the knob pop up and continue turning the control knob to the “OFF position.

Maintenance & Storage

To enjoy years of outstanding performance from your heater, make sure you perform the following maintenance activities on a regular basis:

• Before performing any maintenance always disconnect propane gas tank.

• Use warm soapy water for cleaning. Never use flammable or corrosive cleaning agents.

• Use high-quality automobile wax to help maintain the appearance of your fire pit. Apply to exterior surfaces only, do not apply to burner.

• Spiders and insects can nest in burner or orifices. This dangerous.
  condition can damage fire pit and render it unsafe for use. Clean burner holes by using a heavy-duty pipe cleaner. Compressed air may help clear away smaller particles.

• Carbon deposits may create a fire hazard. Clean dome and burner screen with warm soapy water if any carbon deposits develop.

• If storing this unit inside, disconnect the propane gas tank from the gas valve.

• Always place lid (if applicable) or protective cover on heating item when not in use. Turn control knob OFF.

• Use high-quality automobile wax to help maintain the appearance of your fire pit. Apply to exterior surfaces only.

Caution: Always allow fire pit to cool before attempting service.
NOTE: In a salt-air environment (such as near to ocean), corrosion occurs more quickly than normal. Frequently check for corroded areas and repair them promptly.

Trouble Shooting

cloth.
Igniter battery is dead or backwards| Check that the battery Is inserted correctly in the igniter or replace the battery. Make sure the plastic wrap on the battery has been removed.
Igniter b
Pin cracked or broken – sparks a crack| Please contact Lrving source to reouest Me pans.
Residue on Igniter Pin| Check for residue on the igniter pin or Thermocouple. If diny.thoroughly clean the area. Check that the electrorsc Ignitor Cap is hghtly lined to the spnnglf looseplease adjust me spnng accordingly.
Burner will not light with match| No Gas Flow| Check if me LP gas tank is empty. If empty. replace and refill. If the propane tank Is not empty. refer to Problem: Sudden drop In gas flow on the following page.
Coupling nut and regulator not
— — – rot
fully connected| Turn the coupling nut about one hatl to three a turn. until you feel a solid stop. Do not use toots, tighten by hand only.
Obstruchm of gas flow| Check for bent or kinked hose.
Spider webs or insect nest In the ventun| Chan the venturl.
Burner ports clogged or blocked| Reference Problem: Irregular flame pattern on the following page. Clean the burner ports as descnbed there.
The fire take emits a lot of black smoke when in use| Hose from gas fire table Is pinched| Make sure me hose 6 not pinched between me fire table and me source of the gas.
Flame is being obstructed at burner ports or muing chamber of the bum tube is blocked or obstructed| Make sure that me gas pots on me burner are free of any lava rocks/fire glass so that the flame can flow naturaly.Clear out the mixing chamber located before the Ventun.
Sudden drop in gas flow, or a reduced flame height| Out of Gas| Check for gas in the LP gas tank.
Excess flow safety device may have been activated| Turn control knob to OFF. wan 30 seconds and light outdoor fire tabled flames we still too low. reset the excessive flow safely device by turning off me control knob and LP gas tank valve. Disconnect regulator. Turn burner control knob to HIGH. Wait at least 5 minutes. Turn burner control knob off. Recomect regulator and perform a leek check at lank connection. Turn LP gas tank valve on slowly, wait 30 seconds and then bght outdoor fire table.
Irregular flame pattern. flame does not run the full length of the burner| Burner ports are clogged or blocked| Clean burner porls.Do this by meeting a paperclip nor each of the burner ports to ensure they are not clogged.
WARNING: Make sure turner m not an and has had sulk/ant time to cool before touching it
Flame Wow out| High or gusbng winds| Increase flame to HIGH selling.
Low on LP gas| Replace or refit LP gas tank.
Excess flow valve tripped| Refer to Problem Sudden drop in gas flow.
Flame seems tose heat when burning in cold weather – temper/ion below SO’F| Ice has built up on the outside of the LP gas tank because me vapcnzation process is too low| Tum the control knob and the LP gas lank to OFF. Replace with a spare LP gas lank and resume burning. Store the spare LP gas tank in a well ventilated area. away from children.

Problem: Burner JUST LIGHT UP FOR SECOND AND WILL AUTOMATICALLY TURN OFF

1. The thermocouple will be under the Pilot Guard on the top of the unit.
   Please remove the Pilot guard by unscrewing it from the metal bowl with a screw driver.

2. Once the Pilot Guard has been removed, you will have two components exposed; the copper one is your thermocouple. Please unscrew the nut holding the thermocouple in place.

3. Inside the unit, you will notice that the end of the thermocouple line is directly screwed to the gas valve. Please unscrew the thermocouple from the back end of the gas valve. Do not take off the valve’s silver backing, only unscrew the small nut as shown above.

4. Screw the end of the thermocouple to the back end of the gas valve with the silver backing.
   Once this has been done, please test the unit. You may have to reset the gas valve once again as the safety mechanism may have been set off by the new components introduced:

Resetting Your Gas Valve
Completely detach the propane tank from the table. Do not forget to turn the propane tank valve down. Turn the heat knob to high and leave it on that setting for about two to three minutes.
Once you have done this, please turn the knob back to off. Hook up the quarter of a turn at a time.
propane tank and turn the propane tank’s valve a
NOTE: When reattaching the propane tank, please turn the valve to release the gas back in to the unit VERY SLOWLY. We want the unit to register gas coming through but not too much at once, this will flood the unit and you will have to start all over!
This is so that the gas valve can register the gas coming through a little at a time. Once you have turned the gas on all the way please go ahead and try to light the table again. This should reset your fire table’s safety mechanism

References

• Outdoor Furniture and Home Decor Expert | Outdoor Sectional – COSIEST

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>