ETHAN ALLEN 093051 Tiberius Two Tier Chandelier Instruction Manual

ETHAN ALLEN 093051 Tiberius Two Tier Chandelier

Product Information

• The Tiberius Chandelier 2 Tier is a lighting fixture designed to be installed in a ceiling. It is recommended to have a licensed electrician install the chandelier. The fixture weighs 24 lbs./10.9 kg and requires an electrical junction box in the ceiling to support its weight. The chandelier is shipped with all internal wiring intact and should not be opened or altered.
• It is important to follow the safety instructions provided in the user manual, including not exceeding the rated bulb wattage, keeping flammable materials away from the bulb, and ensuring that the power to the electrical junction box is turned off at the circuit breaker before installation
• The chandelier comes with all the necessary parts for installation, including wire nuts, mounting bar, mounting bar screws, threaded tube with loop, canopy, collar, quick link, chain, cord, loop, pipe, center box, glass shades, sockets, and a ground screw.
• Lightbulbs are not included, except where required by the State of California Title 20. Please refer to the light fixture for bulb specifications. Additional wiring supplies may be required.

Product Usage Instructions

1. Shut off the main electrical supply at the fuse box/circuit breaker.
2. Remove all parts from the carton. Be careful with the glass shades.
3. Detach the mounting bar with the threaded tube from the canopy by loosening the collar.
4. Affix the mounting bar to the ceiling outlet box using the provided mounting bar screws.
5. Guide the wiring from the chain and collar through the canopy and threaded tube.
6. Make proper electrical connections as described in steps 7 to 9. It is recommended to have a licensed electrician perform these connections.
7. Connect the neutral fixture wire to the neutral junction box wire using a wire nut. Twist the connector in a clockwise direction and wrap the connection with electrical tape. Ensure that no wire strands are exposed.
8. Connect the hot fixture wire to the hot junction box wire using a wire nut. Twist the connector in a clockwise direction and wrap the connection with electrical tape. Ensure that no wire strands are exposed. Do not reverse the hot and neutral connections.
9. Carefully push the wire connections back into the ceiling outlet box.
10. Lift the canopy to the ceiling outlet box and secure it with the collar.
11. Screw the glass shades onto the sockets delicately and carefully, without applying too much pressure on the glass.
12. Insert the proper bulbs into the sockets.

Care and Cleaning

For care and cleaning instructions, please refer to the user manual or contact the manufacturer for specific recommendations.

IMPORTANT SAFETY INSTRUCTIONS. READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING.

We strongly recommend that all direct-wired lighting products be installed by a licensed electrician.
Two people may be required for installation. DO NOT EXCEED the rated bulb wattage. Keep flammable materials away from bulb. This light fixture is shipped with all internal wiring intact. Do not open the product or alter the wiring in any manner.
Installation requires an electrical junction box in the ceiling sufficient to support the weight of the light fixture.
This fixture weighs 24 lbs./10.9 kg.

WARNING:
Be certain that the power to the electrical junction box is turned off at the circuit breaker before installation. Turning the power off at a light switch is not sufficient to prevent electrical shock.

CAUTION: Prior to installation, locate ALL INCLUDED PARTS before disposing of packaging materials.

TOOLS REQUIRED FOR INSTALLATION:

1. Screwdrivers
2. Electrical Tape
3. Wire Cutters
4. Pliers
5. Wire Connectors
6. Adjustable Wrench

Note : Lightbulb(s) are not included, except where required by State of California Title 20. See light fixture for bulb specification. Additional wiring supplies may be required.

Description

Assembly Procedure

1. OFF THE MAIN ELECTRICAL SUPPLY AT FUSE BOX/CIRCUIT BREAKER.
2. Remove all parts from carton. Do not throw away any parts. NOTE: Be VERY delicate with the glass shades.
3. Remove Mounting Bar (B), with Threaded Tube (D) attached, from Canopy (E) by loosening Collar (F).
4. Affix Mounting Bar (B) to ceiling outlet box with Mounting Bar Screws (C) provided.
5. Guide wiring from Chain (H) and Collar (F) through Canopy (E) and Threaded Tube (D)
6. Make proper electrical connections described in steps 7—9. A LICENSED ELECTRICIAN IS RECOMMENDED.
7. Attach the BARE WIRE from the fixture to the GROUND JUNCTION BOX WIRE from the OUTLET JUNCTION BOX. Fasten each together with a WIRE NUT (A) by twisting the connector in a clockwise direction and wrap the connection with electrical tape. Make sure that no wire strands are exposed. If your OUTLET JUNCTION BOX DOES NOT have a GROUND WIRE, be sure to insert the GROUND SCREW (P) into the MOUNTING BAR (B), marked as “GND,” facing front, and wrap the fixture’s bare GROUND WIRE around the GROUND SCREW. Tighten the screw to clamp the GROUND WIRE between GROUND SCREW (P) head and MOUNTING BAR (B). IT IS IMPERATIVE THAT THE JUNCTION BOX IN YOUR HOME BE PROPERLY GROUNDED!
8. Connect the NEUTRAL FIXTURE WIRE to the NEUTRAL JUNCTION BOX WIRE. Fasten each together with a WIRE NUT (A) by twisting the connector in a clockwise direction and wrap the connection with electrical tape. Make sure that no wire strands are exposed.
9. Connect the HOT FIXTURE WIRE to the HOT JUNCTION BOX WIRE. Fasten each together with a WIRE NUT (A) by twisting the connector in a clockwise direction and wrap the connection with electrical tape. Make sure that no wire strands are exposed. DO NOT REVERSE THE HOT AND NEUTRAL CONNECTIONS OR SAFETY WILL BE COMPROMISED.
10. Carefully push wire connections back into the ceiling outlet box.
11. Lift Canopy (E) to the ceiling outlet box and secure with Collar (F).
12. VERY delicately and carefully screw the glass shades (M) onto the sockets (N) WITHOUT holding too much pressure on the glass.
13. CARFULLY insert the proper bulb into sockets (N).

Care and Cleaning

1. Wipe with a soft dry cloth.
2. AVOID cleaners, scouring pads, etc.

After troubleshooting, if the lighting fixture still does not work, contact your local Ethan Allen Design Center.
SAVE THESE INSTRUCTIONS
©2017 Ethan Allen Global, Inc

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>