ETHAN ALLEN 09-8042 Fyn Minimalist Picture Light Instruction Manual
- October 30, 2023
- ETHAN ALLEN
Table of Contents
ALLEN 09-8042 Fyn Minimalist Picture Light
Instruction Manual
Fyn Picture Light Assembly Instructions
09-8042 / 09-8043
09-8042 Fyn Minimalist Picture Light
IMPORTANT SAFETY INSTRUCTIONS. READ THESE INSTRUCTIONS COMPLETELY BEFORE
STARTING.
We strongly recommend that all direct-wired lighting products be installed by
a licensed electrician.
Two people may be required for installation. DO NOT EXCEED the rated bulb
wattage. Keep flammable materials away from bulb. This light fixture is
shipped with all internal wiring intact. Do not open the product or alter the
wiring in any manner.
Installation requires an electrical junction box in the wall sufficient to
support the weight of the light fixture.
This fixture weighs 2.9 lbs./ 1.3 kg for 09-8042 and 2.6 lbs. / 1.2 kg for
09-8043.
WARNING: Be certain that the power to the electrical junction box is
turned off at the circuit breaker before installation. Turning the power off
at a light switch is not sufficient to prevent electrical shock.
CAUTION: Prior to installation, locate ALL INCLUDED PARTS before
disposing of packaging materials.
TOOLS REQUIRED FOR INSTALLATION:
- Screwdrivers
- Electrical Tape
- Wire Cutters
- Pliers
- Wire Connectors
- Adjustable Wrench
Note: Lightbulb(s) are included. See light fixture for bulb specification.
| | Parts Included (refer to figure):
---|---|---
Part| Qty| Description| Part| Qty.| Description|
Part| Part| Description
A| 1| Mounting Plate| D| 2| Screw| G| G| Shade
B| 2| Mounting Screw| E| 1| Backplate| H| H| Socket
C| 3| Wire Nut| F| 1| Ground screw| I| I| G9 LED bulb
Assembly Procedure (refer to figure):
SHUT OFF THE MAIN ELECTRICAL SUPPLY AT FUSE BOX/CIRCUIT BREAKER.
- Remove all parts from carton. Do not throw away any parts.
- Remove Mounting Plate (A) from Backplate (E) by loosening Screws (D).
- Affix Mounting Plate (A) to Junction Box with Mounting Screws (B) provided.
- Make proper electrical connections described in steps 6-8.
- A LICENSED ELECTRICIAN IS RECOMMENDED.
- Attach the BARE WIRE from the fixture to the GROUND JUNCTION BOX WIRE from the OUTLET JUNCTION BOX. Fasten each together with a WIRE NUT (C) by twisting the connector in a clockwise direction and wrap the connection with electrical tape. Make sure that no wire strands are exposed. If your OUTLET JUNCTION BOX DOES NOT have a GROUND WIRE, be sure to insert the GROUND SCREW (I) into the Mounting Plate (A), marked as “GND,” facing front and wrap the fixture’s bare GROUND WIRE around the GROUND SCREW. Tighten the screw to clamp the GROUND WIRE between GROUND SCREW (F) head and Mounting Plate (A). IT IS IMPERATIVE THAT THE JUNCTION BOX IN YOUR HOME BE PROPERLY GROUNDED!
- Connect the NEUTRAL FIXTURE WIRE to the NEUTRAL JUNCTION BOX WIRE. Fasten each together with a WIRE NUT (C) by twisting the connector in a clockwise direction and wrap the connection with electrical tape. Make sure that no wire strands are exposed.
- Connect the HOT FIXTURE WIRE to the HOT JUNCTION BOX WIRE. Fasten each together with a WIRE NUT (C) by twisting the connector in a clockwise direction and wrap the connection with electrical tape. Make sure that no wire strands are exposed. DO NOT REVERSE THE HOT AND NEUTRAL CONNECTIONS OR SAFETY WILL BE COMPROMISED.
- Put the lamp onto the Mounting Plate (A) and secure with Screws (D).
- Install proper lightbulb into Socket(H)
Care and Cleaning:
- Wipe with a soft dry cloth.
- AVOID cleaners, scouring pads, etc.
After troubleshooting, if the lighting fixture still does not work,
contact your local Ethan Allen Design Center.
SAVE THESE INSTRUCTIONS
©2021 Ethan Allen Global, Inc.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>