JOROTO X2PRO Bluetooth Stationary Exercise Bike User Manual

User Manual JOROTO-X2PRO

Read all instructions carefully before using this product. Retain this owner’s manual for future reference. If you have any inquiries or require further assistance, please contact JOROTO Customer Support.
Scan the Instagram QR Code to reach us online!
Email: [email protected]

JOROTO.SPORTS.FITNESS

EXPLODED-VIEW & PARTS LIST

Dear Customer,
Please read this instruction very carefully before using this item. You will find important information regarding safety of your exercise bike.

IMPORTANT SAFETY NOTICE

Note the following precaution before assembling or operating the machine.

1. Keep children and pets away from the bike at all times. DO NOT leave unattended children in the same room with the machine.

2. Handicapped or disabled persons should not use the bike.

3. lf the user experiences dizziness, nausea, chest pain, or any other abnormal symptoms, STOP the workout at once.CONSULT APHYSICIAN IMMEDIATELY.

4. Before beginning training. remove all within a radius of 2 meters from the machine. DO NOT place any sharp objects around the bike.

5. Position the bike on a clear, level surface away from water and moisture. Place mat under the unit to help keep the machine stable and to protect the floor.

6. Use the bike only for its intended use as described in this manual. DO NOT use any other accessories not recommended by the manufacturer.

7. Assemble the machine exactly as the descriptions in the instruction manual.

8. Check all bolts and other connections before using the machine for the first time and ensure that the trainer is in the safe condition.

9. Hold a routine inspection to the equipment. Tighten all bolts on a regular basis. Pay special attention to components which are the most susceptible to wear off, i.e. connecting points and wheels.
   The defective components should be replaced immediately. The safety level of this equipment can only be maintained by doing so. Please don’t use the bike until it is repaired well.

10. NEVER operate the bike if it is not functioning properly.

11. This machine can be used for only one person’s training at a time.

12. Do not use abrasive cleaning articles to clean the machine. Remove drops of sweat from the machine immediately after finishing training.

13. Always wear appropriate workout clothing when exercising. Running or aerobic shoes are also required.

14. Before exercising, always do stretching first.

15. The power of the machine increases with increasing the speed, and the reverse. The machine is equipped with adjustable knob, which can adjust the resistance.

WARNING: BEFORE BEGINNING THIS OR ANY EXERCISE PROGRAM, CONSULT YOUR PHYSICIAN FIRST. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS.READ ALL INSTRUCTIONS BEFORE USING THE BIKE.JOROTO ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.

PART LIST

INSTALLATION STEPS

Step 1: Assemble the Stabilizers

1. Set the Carriage Screws (86) through Rear Stabilizer (B), Main Frame (A) and Flat Washer (88), use the Cap Nuts (87) to fix them.
2. Fix Front Stabilizer (C) on the Main Frame (A) by using the same way.

Step 2: Assemble the Pedals

1. Rotate and insert the Left Pedal (J1) into the Left Crank (52) (PS:On your left when sitting on the bike), use Fixing Nut (99L) to fix the Left Pedal (J1).
2. Rotate and insert the Right Pedal (J2) into the Right Crank (53) (PS:On your right when sitting on the bike), use Fixing Nut (99R) to fix the Right Pedal (J2).
   

Step3: Assemble Vertical Seat Post and Handlebar Post

1. Insert Vertical Seat Post (D) into the position as the picture shows. Select an appropriate height and use Spring Knob (43) to fix it.
2. Insert Handlebar Post (E) into the position as the picture shows. Select an appropriate height and use L Knob (89) to fix it.
   

Step 4: Assemble the Monitor, Seat Post and Handlebar

1. Set Seat (H) on the fixing tube of Seat Post (G) and adjust it to the appropriate position, then tighten the bolts under Seat (H).
2. Set Seat Post (G) on Vertical Seat Post (D), then use Large Washer (91) and L Knob (90) to fix it.
3. Set Handlebar (F) on Handlebar Post (E), then use Large Washer (91) and L Knob (90) to fix it.
   

Step 5: Assemble the Seat and connect the Monitor

1. Assemble the batteries in Monitor first.
   Unscrew 4 Phillips Screws (96) at the back of Monitor (I), then attach Monitor (I) on Handlebar (F) and use Phillips Screws (96) to fix it.

2. Attach Sensor Cable (57) to Monitor Connecting Cable (97).

3. Assemble the Bottle Shelf Use the Umbrella Head Phillips Screw (11) to assemble the Bottle Shelf (M) on the Main Frame (A) as the picture shows.

Assembly Completed

MONITOR INSTRUCTION

DISPLAY FUNCTION

. Scan every function automatically every 6 seconds.
. Press MODE/ENTER, all functions will be shown in order : TIME— DIST—.CAL-.RPM/SPEED.
TIME| . Without preset target, TIME will accumulate.
. With preset target, TIME will count down from the target. When it arrives 0, it will beep to remind the trainer.
. When training, if there is any signal input for 4 second, TIME will stop.
. Range: 0:00 – 99:59
DISTANCE| . Without preset target, DISTANCE will accumulate.
. With preset target, DISTANCE will count down from the target. When it arrives
remind the trainer.
. Range: 0:00 – 99:99
CALORIES| . Without preset target, CALORIES will accumulate.
. With preset target, CALORIES will count down from the target. When it arrives remind the trainer.
. Range: 0-9999
WATT| . Display power consumed during training. . Range: 0-999
LOAD| . Display the adjusted resistance level. . Range: 1-100%
SPEED| . If no signal input for over 4 seconds when training, SPEED will show as “0.0”. . Range: 0.0 – 99.9
RPM| . If no signal input for over 4 seconds when training, RPM will show as “0.0”. . Range: 0 – 999

BUTTON FUNCTION

quickly. •
. TIME Setting Range: 00:00-99:00 (Add 1:00 each time)
. CAL Setting Range: 0-9990 (Add 10 each time)
. DIST Setting Range: 0.00-99.50 (Add 0.5 each time)
DOWN| . Press DOWN to decrease the digit. Press and hold, the digit could decrease quickly. . TIME Setting Range: 00:00-99:00 (Decrease 1:00 each time)
. CAL Setting Range: 0-9990 (Decrease 10 each time)
. DIST Setting Range: 0.00-99.50 (Decrease 0.5 each time)
MODE/ENTER| . Press MODE/ENTER to select each function.
Press and hold MODE/ENTER for 2 seconds, all digits will be cleared.
RESET| . Under Setting mode, press RESET once can clear all current digits. . Press and hold RESET for 2 seconds can also clear all digits.

OPERATIONAL PROCEDURE

Turn on
LCD Display, shown as Fig 1.
Turn off
If no signal input for over 4 minutes, the monitor will go to Sleep Mode.

Operation

1. Training Setting
   Press MODE/ENTER to select functions: TIME, DISTANCE, CALORIES. Press UP or Down to set the target digit, press UP to increase, press DOWN to decrease. Press MODE/ENTER to confirm after finish the setting.
   Set TIME as an example: when the digit of time bleeps, press UP/DOWN to set the digit, press MODE/ENTER to confirm and goes to the next setting. The setting of DISTANCE, CALORIES is the same as TIME.
   When start training and the signal is detected by monitor, the digit of SPEED/RPM, TIME, DISTANCE and CALORIES will add up.

TROUBLESHOOTING

When the display dims, please replace the batteries.
If there is no signal shown when training, please check if the sensor cable is well connected.

Note

1. If there is no signal input for over 4 minutes, the display will dim.
2. If there is an error on the display, please re-assemble the batteries and try again.

APP CONNECTION

1. Search “KINOMAP” in the mobile app store to download the app.
   

2. After the download is complete, open the APP and register your personal information, turn on the Bluetooth of your mobile phone, and make sure that the monitor is powered on and awake.

3. Add sports equipment, the specific operations are as follows:
   

4. After the equipment is connected, choose the scene you like and start your workout!

Note

1. This monitor can connect APP on the smart device by Bluetooth.
2. This monitor is connected by using Iconsole protocol.
3. When the monitor is connected with the smart device, there will be no digits on the display, the digits will be shown on the smart device.

FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the users authori­ty to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or televi­sion reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference, and
• this device must accept any interference received, including interference that maycause undesired operation. RF Exposure StatementTo maintain compliance with FCC’s RF Exposure guidelines, This equipment should beinstalled and operated with minimum distance of 5mm the radiator your body.

This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.

IC warning
This device contains licence-exempt transmitter(s)/receiver(s)/ that comply with Innovation Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

• this device may not cause interference and
• this device must accept any interference, including interference that may cause undesired operation of the device. Radiation Exposure: This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment; To maintain compliance with IC’s RF Exposure guidelines, This equipment should be. installed and operated with minimum distance of 5mm the radiator your body. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.

Li’ang Health Science and Technology (Beijing) Co.,Ltd
Tel: 1-888-828-2521 86-400-700-5199
Scan the Instagram QR Code to reach us online
Email：[email protected]

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>