JOROTO X2 Stationary Exercise Bike Instructions
- June 9, 2024
- JOROTO
Table of Contents
JOROTO X2 Stationary Exercise Bike
MONITOR INSTRUCTION
DISPLAY FUNCTION
**** SCAN| · Under SCAN mode, press MODE/ENTER to select functions.
. Scan every function automatically every 6 seconds.
. Press MODE/ENTER, all functions will be shown in order: TIME-> DIST—->C AL — >RPM/SPEED.
---|---
**** TIME| . Without preset target, TIME will accumulate.
. With preset target, TIME will count down from the target. When it arrives 0, it will beep to remind the trainer.
. When training, if there is any signal input for 4 second, TIME will stop.
. Range: 0:00 – 99:59
**** DISTANCE| . Without preset target, DISTANCE will accumulate.
. With preset target, DISTANCE will count down from the target. When it arrives 0, it will beep to remind the trainer.
. Range: 0:00 – 99:99
**** CALORIES| . Without preset target, CALORIES will accumulate.
. With preset target, CALORIES will count down from the target. When it arrives 0, it will beep to remind the trainer.
. Range: 0-9999
**** WATT| . Display power consumed during training.
. Range: 0-999
**** LOAD| . Display the adjusted resistance level.
. Range: 1-100%
**** SPEED| . If no signal input for over 4 seconds when training, SPEED will show as “0.0”.
. Range: 0.0 – 99.9
**** RPM| . If no signal input for over 4 seconds when training, RPM will show as “0.0”.
. Range: 0 – 999
BUTTON FUNCTION
ITEM/DESCRIPTION
**** UP| . Press UP to increase the digit. Press and hold, the digit could increase quickly.
. TIME Setting Range: 00:00- 99:00 (Add 1:00 each time)
. CAL Setting Range: 0-9990 (Add 10 each time)
. DIST Setting Range: 0.00- 99.50 (Add 0.5 each time)
---|---
**** DOWN| . Press DOWN to decrease the digit. Press and hold, the digit
could decrease quickly.
. TIME Setting Range: 00:00-99:00 (Decrease 1:00 each time)
. CAL Setting Range: 0-9990 (Decrease 10 each time)
. DIST Setting Range: 0.00- 99.50 (Decrease 0.5 each time)
**** MODE/ENTER| . Press MODE/ENTER to select each function.
. Press and hold MODE/ENTER for 2 seconds, all digits will be cleared.
**** RESET| . Under Setting mode, press RESET once can clear all current digits.
. Press and hold RESET for 2 seconds can also clear all digits.
OPERATIONAL PROCEDURE
Turn on
- LCD Display, shown as Fig 1.
Turn off
- If no signal input for over 4 minutes, the monitor will go to Sleep Mode.
Operation
- Training Setting
- Press MODE/ENTER to select functions: TIME, DISTANCE, CALORIES. Press UP or Down to set the target digit, press UP to increase, press DOWN to decrease.
- Press MODE/ENTER to confirm after finish the setting.
- Set TIME as an example: when the digit of time bleeps, press UP/DOWN to set the digit, press MODE/ENTER to confirm and goes to the next setting. The setting of DISTANCE,
- CALORIES is the same as TIME.
- When start training and the signal is detected by monitor, the digit of SPEED/RPM, TIME, DISTANCE and CALORIES will add up.
TROUBLESHOOTING
- When the display dims, please replace the batteries.
- If there is no signal shown when training, please check if the sensor cable is well connected.
Note
- If there is no signal input for over 4 minutes, the display will dim.
- If there is an error on the display, please reassemble the batteries and try again.
APP CONNECTION
- Search “KINOMAP” in the mobile app store to download the app.
- After the download is complete, open the APP and register your personal information, turn on the Bluetooth of your mobile phone, and make sure that the monitor is powered on and awake.
- Add sports equipment, the specific operations are as follows
- After the equipment is connected, choose the scene you like and start your workout!
Note
- This monitor can connect APP on the smart device by Bluetooth.
- This monitor is connected by using the!console protocol.
- When the monitor is connected to the smart device, there will be no digits on the display, the digits will be shown on the smart device.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>