SW-MOTECH YAMAHA YZF-R7 21 Crash Pad Kit Instructions
- June 12, 2024
- SW-MOTECH
Table of Contents
SW-MOTECH YAMAHA YZF-R7 21 Crash Pad Kit
Product Information
Product Name : ANBAUANLEITUNG
Model Numbers: STP.06.590.11300/B, STP.06.590.81300/B, STP.00.590.10001/B
Product Usage Instructions
To use the ANBAUANLEITUNG product, please follow the steps below:
- Ensure that you have all the necessary tools and equipment required for installation.
- Identify the model number of your ANBAUANLEITUNG product (STP.06.590.11300/B, STP.06.590.81300/B, or STP.00.590.10001/B).
- Refer to the specific installation manual provided with your model number for detailed step-by-step instructions.
- Carefully read and understand the instructions before proceeding with the installation.
- Make sure the installation area is clean and free from any obstructions.
- Follow the recommended safety precautions while handling the ANBAUANLEITUNG product.
- Depending on the model, use appropriate fasteners and tools to securely attach the product to the desired surface.
- Double-check all connections and ensure they are tightly secured.
- If any electrical connections are required, ensure they are done by a qualified professional following local electrical codes and regulations.
- Once the ANBAUANLEITUNG product is installed, test its functionality to ensure proper operation.
- If you encounter any issues during installation or usage, refer to the troubleshooting section in the manual or contact our customer support for assistance.
For any further information or queries, refer to the complete user manual provided with your ANBAUANLEITUNG product.
MOUNTING INSTRUCTIONS
Revision: 00 Datum / Date: 06 – 2021
Mounting kit for frame slider
Thank you for choosing this premium product from SW-MOTECH. Please visit
our webshop for additional information, such as application charts and PDF
mounting instructions. Any other documents that may be required (e.g. ABE
certifications). are also available for download at our webshop. Installation
and/or maintenance of this product require good technical understanding! For
your own safety SW-MOTECH recommends having installation and/or servicing
carried out by a specialist workshop! SW-MOTECH assumes no liability for
damage caused by improper installation and/or maintenance work! Carefully
follow all the directions given in the mounting instructions and pay attention
to all relevant information in the vehicle manual during assembly.
Nonconformance can lead to vehicle damage or even endanger the driver! These
mounting instructions are written based on our current state of knowledge.
Legal requirements for accuracy do not exist. This product was developed for
vehicles in their factory setting. Compatibility with original accessory parts
or other manufacturers’ accessory parts is not guaranteed. Furthermore, BEFORE
installing this product, make sure that all moving parts (e.g. the chain) are
in the original state Of maintenance. Installed accessories can change the
driving behaviour and/or stability of your vehicle.
GENERAL INFORMATION
Observe the countryrspecific regulations concerning vehicle registration/ operation as well as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority
PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you
MOUNTING : All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturers’ specifications or replaced by parts delivered by SW-MO TECH. Secure all threads. unless othervvise specified, with medium-strength liquid thread locker. Torque specifications undefined by SW-MOTECH must be obtained from the vehicle manufacturer or by a specialist workshop!
FUNCTION CHECK: After installation make Sure that all parts and connections previously removed are properly replaced. Also make sure that no moving parts are obstructed and no function of the vehicle is hindered in any way. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all screw connections and the proper fit Of the product.
PARTS LIST
Note.
- a All measurements in millimeters.
- b The second number indicates the total quantity Of the part in the delivery
No torque specifications: use the torque defined by vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.
MOUNTING
ATTENTION : Do not start mounting the right frame slider until you have
completed the installation of the left frame slider! Remove the original
engine bolt from the left mounting point Attach the mounting plate (1) to the
vehicle, as shown in the drawing
ATTENTION : Use liquid thread locker! Before tightening the screw (2),
adjust the mounting plate (I) according to the alignment of the vehicle
Tighten the screw (2) with the manufacturers’ specified torque Repeat the
installation on the right side of the vehicle
Attach the shown parts to the mounting plates Ill on both sides.
NOTE: Also refer the mountyng instructions of the frame slider set
ATTENTION : Use liquid thread locker! Tighten the screws (61 as
specified.
Revision: 00 Datum / Date: 10 – 2019
Crash pad set
Thank you for choosing this premium product from SW-MOTECH. Please visit
our webshop for additional information, such as application charts and PDF
mounting instructions. Any other documents that may be required (e.g. ABE
certifications), are also available for download at Our webshop. Installation
and/or maintenance of this product require good technical understanding! For
your own safety SW-MOTECH recommends having installation and/or servicing
carried out by a specialist workshop! SW-MOTECH assumes no liability for
damage caused by improper installation and/or maintenance work! Carefully
follow all the directions given in the mounting instructions and pay attention
to all relevant information in the vehicle manual during assembly.
Nonconformance can lead to vehicle damage or even endanger the driver! These
mounting instructions are written based on our current state Of knowledge.
Legal requirements for accuracy do not exist. This product was developed for
vehicles in their factory setting. Compatibility with original accessory parts
or other manufacturers’ accessory parts is not guaranteed. Furthermore, BEFORE
installing this product, make sure that all moving parts (e.g. the chain) are
in the original state of maintenance. Installed accessories can change the
driving behaviour and/or stability Of your vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration/
operation as well as TUV regulations if applicable. If required, register
installed parts in the vehicle documents through an appropriate inspection
authority
PREPARATION : Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you
MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturers’ specifications or replaced by parts delivered by SW-MO TECH. Secure all threads, unless otherwise specified, with medium-strength liquid thread locker. Torque specifications undefined by SW-MOTECH must be obtained from the vehicle manufacturer or by a specialist workshop!
FUNCTION CHECK: After installation make sure that all parts and connections previously removed are properly replaced. Also make sure that no moving parts are obstructed and no function of the vehicle is hindered in any way. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all screw connections and the proper fit of the product.
PARTS LIST
- All measurements in millimeters.
** The second number indicates the total quantity of the part in the delivery.
*** No torque specifications: Use the torque defined by vehicle manufacturer! The standard torque in this table can be used as long as it is within the vehicle manufacturer’s specifications.
- Step 1 Attach the crash pads (1) on both sides to the adapter plates of your SW-MO TECH slider set for frame, as described in the mounting instructions of the slider set for frame.
- Step [2]: Place the logo inserts (2) on both sides into the crash pads
- Step [3]: . . and attach them with the screws (3).
Tighten the screws (3) CAREFULLY by hand (max. 1,2 Nn)!
Copyright by SW-MOTECH GmbH & co. KG
Errors and omissions excepted. Technical and design modifications are subject
to change
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>