WEEFiNE Solar Flare 13000 Pro Underwater Videolight User Manual

June 12, 2024
WEEFINE

WEEFiNE Solar Flare 13000 Pro Underwater Videolight

Standard Accessories

WEEFiNE-Solar-Flare-13000-Pro-Underwater-Videolight-FIG-1
\(1\)

Specification

WEEFiNE-Solar-Flare-13000-Pro-Underwater-Videolight-FIG-1
5

Description of components

WEEFiNE-Solar-Flare-13000-Pro-Underwater-Videolight-FIG-1
\(2\)

Installation of battery

  1. Unscrew the lamp base;
  2. Load the battery into the cartridge according to following figure (as shown below);
  3. Screw the shown in the following figure.

Operating instructions

Startup
In the off state, long press the key “1S” to turn on the power and make the display screen on, and then enter the astigmatism mode, with the brightness of 100%.
Shutdown
Long press the key for more than 25 to shut down in any mode and any brightness;
Brightness control

  • Increase brightness: turn the adjusting knob clockwise;
  • Reduce brightness: turn the adjusting knob anticlockwise;
  • White light: 12 gears from 0 to 100 in total, corresponding to the following brightness;WEEFiNE-Solar-Flare-13000-Pro-Underwater-Videolight-FIG-1 6

SOS mode
In the off state, long press the key for over 3s to enter the SOS mode, short press key SOS -> switch sharp-flash, and long press the key for over 2s to shut down;
Temperature protection function
When the lamp base reaches 55C, enter the temperature protection function to change the brightness to 20%. When the temperature is lower than 40 C, “HOT” will be displayed in the display screen to exit the temperature protection function and restore the brightness;
Flash trigger mode

  • Enter flash trigger mode: Long press the key for 1S to enter the flash trigger mode in the work mode of normal video light;
  • Operate in the flash trigger mode: At this time, the focal brightness is 5%. When the flashing signal is received, the light will be on and flash, and the light will automatically switch back to the focusing light after 0.15.
  • Flash brightness adjustment: in the flash trigger mode, rotate the knob to adjust the flash brightness, increase in clockwise, decrease in anticlockwise, with 10 gears in total;
  • Exit the flash trigger mode: Long press the key for 1S to exit and enter the video light operating mode, and switch to the original video light brightness;

Low-voltage protection
In case of low volage, it will reduce the brightness to 10% and display the countdown of 10 minutes. After 10 minutes, it will shut down automatically. In this mode, the flash trigger function cannot be used;
Remote control function
This machine supports the WFA03 remote control unit; a special optical fiber is used to connect the remote control unit and the remote optical fiber jack; remote operation: short press the left key for decrease (gear, brightness), short press the right key for increase (gear, brightness); long press the middle key to make the machine enter the low power mode, and long press it again to wake up the machine.

Battery charging

  1. Connect the AC terminal of the special charger to the power socket; At this time, the charger indicator light is green;
  2. Insert the DC terminal of the special charger into the charging hole; When the charging is started, the charger indicator light turns from green to red;
  3. When the battery is fully charged, the charger indicator light turns green.
  4. Any charger other than the special charger provided by the manufacturershould be used.WEEFiNE-Solar-Flare-13000-Pro-Underwater-Videolight-FIG-1 \(4\)

Battery
When the battery is low, the brightness of the photography light will be reduced automatically to save power. The photography light will be shut down when the battery runs out.

Display screen operation displayWEEFiNE-Solar-Flare-13000-Pro-Underwater-
Videolight-FIG-1 \(5\)

  1. Flash brightness gear
  2. Brightness level/ endurance
  3. Flash indication
  4. Light group operating status indication

Maintenance

  1. Soak the machine in fresh water for 30 minutes after diving;
  2. When the battery is not used for a long time, the best storage capacity is 70%;
  3. The battery shall be charged and discharged once every 6 months at most;
  4. There are two waterproof O-rings on the lamp holder. Silicone oil should be used to keep the O-ring well-lubricated. If the O-ring is cracked, hardened, damaged, deformed, etc., it should be replaced in time.

Note: Do not use sharp tools to remove the O-ring. Warning

  1. Do not open the tail cover when the photography lamp is in the water.
  2. Do not direct the light into your eyes or others’ eyes;
  3. Do not touch the battery and charger with wet hands.
  4. Only batteries and special chargers provided by the manufacturer can be used;
  5. If you do not use the photographic lamp for a long time, the battery should be taken out and stored properly;
  6. users do not disassemble or repair lamps, batteries, and special chargers; In case of failure, please contact local dealers; Please follow the instructions, otherwise, it may cause damage to the camera lamp, personal injury, and failure of warranty.

Warranty

Weefine provides a warranty against manufacturer defects for 1 year starting from the date of purchase. Manufacturer defects occurring within 15 days of the date of purchase will result in an exchange of products at the vendor. All other manufacturer defects occurring within 1 year of the purchase will be repaired at no cost. Proof of purchase is required for warranty support. The warranty does not cover failures or defects resulting from misuse (e.g.; modification; damage), natural disasters, or battery issues, including incorrect battery installation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals