WEEFiNE WFS05 Flash Light User Manual

June 8, 2024
WEEFINE

WFS05 FLASH LIGHT
MANUAL

Please read the manual carefully before using the video light

Component

① YS Adapter
② Screen display
③ Adjustment knob A
④ Gear knob B| ⑤ Button A
⑥ Button B
⑦ Wide light
⑧ Red light| ⑨ Tail cap
⑩ Remote port
⑪ Strobe Port
⑫ Indicator
---|---|---

Specifications

Full power guide number at 1m/lOS 100 24
Waterproof 100m
Max. power 80Ws
LED lighting 1 watt spot light and 1 watt red light
Brightness(Lumen) 200 Im ( Wide light )
Color Temperature 6000K ( Wide light )
Flash index level GN/1/1.4/2/2.8/4/5.6/8/11/16/22/24
Flashes per full charge Full power is greater than 1200 times
Recycle time 0.1s-1.5s (Depends on greater than flash intensity)
Battery 4*18650Li-ion batteries (3400 mAh)
Size 119 (L)x 119mm(W) x 135.5(H) mm
Weight 1050g on land (Include the battery ) 240g underwater (Include the

battery )

Unpacking

To install the battery

  1. Turn the tail cap counter-clockwise to open.
  2. Loading the Li-ion battery into the tail cap, make sure the polarity battery must match the polarity of the diving light contacts.
  3. Turn the tail cap clockwise to reattach the tail to the head of the flash light.

Operate the light
(OFF state), Press the buttons A and B at the same time adjust the screen orientation mode (flip screen up and flip screen down), Press and immediately release the Button A enter the screen mode, Press the buttons A and hold it down for more than 2 seconds

Turn ON
(OFF state) Press and immediately release the Button A
Turn OFF
(ON state) Press the buttons A and hold it down for more than 2 seconds

Trigger flash
Press and immediately release the Button A (it does not include synchronization mode).

Switch mode
(ON state) Press and immediately release the Button A

Press the buttons B and hold it down for more than 2 seconds

S1=Single trigger mode S2=Double trigger mode Sync=Synchronous mode

Brightness adjustment
(Adjustment knob A) Rotate clockwise + ;
Wide light: Totally 10 levels from 0 to 100, A level is 10% ;
(Adjustment knob A) Rotate counterclockwise- ;
Wide light: Totally 10 levels from 100 to 0.

Brightness adjustmentc Flash
On S1/S2 mode ( it does not Flash intensity display synchronization mode) When the gear knob B is rotated to different gears, the guide number will change according to the current gear value to adjust the intensity of the flash.

Strobe mode
On S1 mode, Flash light flashes when a single flashing signal is received.
On S2 mode, Flash light flashes when two flashing signals are received within 1 second.
On Sync mode, (it must be connected to fiber optic cable) received flash signal, according to the letter To flash.

Function of remote control
( the remote control button for the first time is invalid ) Press the middle button and hold it down for more than 2seconds

Press and immediately release the middle button (On Flash mode)

Press and immediately release the middle button (On LED mode)

Short press left button or right button, in L mode, you can adjust the intensity of current light (red light/astigmatism).

Memory function
On normal mode, the current state will be recorded when the machine is shut down, and the same state will be recorded when the machine is turned on again.

Low power protection
When the battery voltage is too low, all the Buttons are invalid and can only be turned off.

To Charge the battery

  1. Insert the DC charger plug into the battery.
  2. Plug the charger into the wall receptacle. When the battery beings to charge the indicator light on the charger will be red.
  3. When the battery is fully charged the indicator light on the charger will turn green.

General Maintenance
There two-rings in the tail cap. Use silicone to keep the O-rings well lubricated. It is important to lubricate the o-rings if the flashlight has not been used in a long time or if the o-ring is hard. If the O-ring is damaged, broken or deformed it should be replaced with the spare.
Note: Do not use a sharp tool to remove the O-rings.

Warning

  1. Do not open the tail cap when the video light is in the water.
  2. Do not shine the light directly into your eyes or another person’s eyes.
  3. Do not touch the battery and charger with wet hands.
  4. Use only the manufacturer’s battery and charger with this system.
  5. If the flash light will not be used for a long period of time the battery should be removed.

Failure to comply with these warning may result in damage to the video light and will nullify the warranty.

Warranty

We provides a warranty against manufacturer defects for 1 year starting from the date of purchase. Manufacturer defects occuring within 15 days of the date of purchase will result in an exchange of product at the vendor. All other manufacturer defects occuring within 1 year of the purchase will be repaired at no cost. Proof of purchase is required for warranty support. The warranty does not cover failures or defects resulting from misuse (e.g; modification; damage), natural disasters, or battery issues, including incorrect battery installation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals