CP electronics EBDHS-B-MB-CB-DD High Bay Presence Detectors Installation Guide

WDA033 Issue 3 Installation Guide
EBDHS-B-MB-CB-DD

EBDHS-B-MB-CB-DD High Bay Presence Detectors

Casambi DALI digital dimming, luminaire batten mounted, high bay/high level

Warning
This device should be installed by a qualified electrician in accordance withthe latest edition of the IEE wiring regulations.
Downloads and Videos

http://cpelectronics.co.uk/cp/A033qr

Dimensions (mm)

Wiring

Dimming ouputs
DALI is not an SELV output and should be treated as if it is at mains potential. Use mains rated wiring.
Key

1. Neutral
2. Live
3. 10A circuit protection
4. Load
5. DALI+ (white), DALI- (red)
6. Live Out

Unswitched DALI load Wiring

Switched load Wiring

Detection pattern

Walk across

Walk towards

Walk towards & walk across explained

http://cpelectronics.co.uk/cp/wtaqr

Alignment marks

The sensor head has 4 alignment marks. These correspond to the 4 outer passive infrared sensors under the lens. Use these marks to align with aisles and corridors to ensure the best detection characteristics.

Masking shields

The EBDHS can be used with two clip-on masking shields, (supplied separately) enabling precise masking of the detection shape for aisles and corners as well as narrowing the detection diameter.

1. Lateral trim pattern for slot style detection.
2. Radial trim pattern for narrowing the detection diameter.

**** Ensure all infra-red (IR) programming is completed before affixing the masking shields to the detector.

Masking shield application

Aisles
Trim the masks laterally to reduce the detection width for aisles.

wt 3.6m x 8m
2| wa 12.8m x 40m
wt 9.6m x 30m| wa 8.3m x 26m
wt 6.4m x 20m| wa 5.1m x 16m
wt 3.8m x 12m| wa 2.8m x 9m
wt 2.5m x 8m
3| wa 8.8m x 40m
wt 6.6m x 30m| wa 5.7m x 26m
wt 4.4m x 20m| wa 3.5m x 16m
wt 2.6m x 12m| wa 1.9m x 9m
wt 1.7m x 8m
4| wa 4.4m x 40m
wt 3.3m x 30m| wa 2.8m x 26m
wt 2.2m x 20m| wa 1.7m x 16m
wt 1.3m x 12m| wa 0.9m x 9m
wt 0.8m x 8m

Key
a. Trim line
b. 15m Mounting height
c. 10m Mounting height
d. 6m Mounting height
e. 3m Mounting height
wa = walk across
wt = walk towards

Install shields to detector

Align trimmed shields with sensor head alignment marks and aisle.

Narrow detection

Trim the masks along radial lines to narrow the detection diameter.

wt 7.1m
2| wa 25.2m
wt 18.9m| wa 16.3m
wt 126m| wa 10m
wt 7.5m| wa 5.6m
wt 5m
3| wa 18m
wt 13.5m| wa11.7m
wt 9m| wa 7.2m
wt 5Am| wa 4m
wt 3.6m
4| wa 12.8m
wt 9.6m| wa 8.3m
wt 6.4m| wa 5.1m
wt 3.8m| wa 2.8m
wt 2.5m
5| wa 8.8m
wt 6.6m| wa 5.7m
wt 4.4m| wa 3.5m
wt 2.6m| wa 1.9m
wt 1.7m

Key
a. Trim line
b. 15m Mounting height
c. 10m Mounting height
d. 6m Mounting height
e. 3m Mounting height
wa = walk across
wt = walk towards

Install shields to detector

Align trimmed shields with sensor head alignment marks and aisle.

**** Sensor Configurations

Configure the sensor controls via the Casambi App from Apple App Store or Google Play Store.
For light regulation control, ensure that the setting below is made and allow for a few minutes to take effect:
[Use the full dim range] = enable
See CP Electronics Casambi Application Guide.
The communication range between two Casambi units is highly dependant on the surrounding and obstacles, such as walls and building materials. In indoor environments the range can be up to 30 m and in outdoor conditions up to 50 m. In the majority of applications Casambi units are only ever 5 to 6 meters away from each other to provide excellent reliability in the communication network.

Installation

This unit is designed for install as an integration to the stomer’s product.

• Do not site the unit where direct sunlight might enter the sensor.
• Do not site the sensor within 1m of any lighting, forced air heating or ventilation.
• Do not fix the sensor to an unstable or vibrating surface.
• Occupancy is best detected when the ambient temperature is different to that of the human body, thus, use within -20 to 35ºC ambient temperature.

Standard luminaire fitting

Wire in plugs & connect to detector

Key

1. M20 nut
2. IP spacer

IP luminaire fitting

Wire in plugs & connect to detector

Key

1. M20 nut
2. 5° washer (optional)
3. Silicone washer
4. IP spacer

• Note: Use the 5° spacers where the luminaire has a draft angle.
• Ensure that the silicone washer and/or IP spacer are used to maintain IP rating.

Technical Data

contactor
Max DALI dim load| Up to 10
Cable specification| 5 x 1mm2 solid core PVC
sheath 90ºC
Light detection range| 1-999 lux
Transceiver frequency| 2.4GHz ISM band
Transceiver power| Up to 4 dBm output power
and -93 dBm RX sensitivity
Rated impulse voltage| 2500V
Purpose| Sensing control
Operational temperature| 0 to 50°C
Humidity| 5 to 95% non-condensing
Material (casing)| Flame retardant ABS
Insulation class| Class 2
IP rating| 40
Compliance|
| CP Electronics
A Business unit of Legrand Electric Limited,
Brent Crescent, London NW10 7XR, UK
t. +44 (0)333 900 0671
enquiry@cpelectronics.co.uk|
---|---|---
www.cpelectronics.co.uk| Connect with us

Due to our policy of continual product improvement CP Electronics reserves the right to alter the specification of this product without prior notice.

WDA033 Issue 3 Installation Guide, EBDHS-B-CB-MB-DD
A brand of 21307

Documents / Resources

| CP electronics EBDHS-B-MB-CB-DD High Bay Presence Detectors [pdf] Installation Guide
EBDHS-B-MB-CB-DD, High Bay Presence Detectors, EBDHS-B-MB-CB-DD High Bay Presence Detectors, Presence Detectors, Detectors
---|---

References

• Home | Legrand
• CP Electronics | Brands | Legrand United Kingdom

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>