CRYSTORAMA 1157-PB-CL-MWP 37 Inch Polished Brass Chandelier Ceiling Light Instruction Manual

CRYSTORAMA 1157-PB-CL-MWP 37 Inch Polished Brass Chandelier Ceiling Light

Product Information

The model number of the product is #1157-PB-CL-MWP. The product is manufactured by Crystorama.com. The fixture is Damp rated. The product requires 20 Candelabra Base Bulbs with a recommended wattage of 40 Watts and a maximum wattage of 40 Watts. LED bulbs are recommended for extended use. The product comes with various parts including a canopy, collar ring, collar loop, chain, center column kit, arms with holders, male plugs, PVC candle sleeves, metal washers, check rings, coupling, glass vase, thread, and a finial.
WARNING : This product can expose you to Lead, which is known to the State of California to cause cancer and/or birth defects or reproductive harm. For more information go to www.p65warnings.ca.gov.

Product Usage Instructions

1. Place the fixture parts on a soft cloth-covered platform before installation of the fixture.
2. To install the 6 arms, slightly loosen each screw on the metal plate. Pull a female plug through a hole in the upper metal plate. Connect the male plug at the end of the upper arm with the female plug that was just pulled. Push the end of the arm with the metal tab through the hole until stopped by the metal tab (this should also push the wires and plugs back inside the metal plate). Twist the metal tab counter-clockwise until both inserts lock onto the loose screws. Tighten the screw securing the arm in place. Repeat for all 6 arms.
3. Repeat Step 2 for the 10 and 15 arms. The 10 arms attach on the middle tier and the 15 arms attach on the bottom-most tier.
4. Thread the threaded pipe into the coupling at the bottom of Center Column Kit 2. Place the glass vase, check ring, metal washer, bobeche, and metal washer in that order. Secure with the finial.
5. Screw the Center column kit 1 onto the center column kit 2.
6. Set the mounting hardware onto the beam.
7. Decide the desired hanging height and adjust the chain to the correct length.
8. Raise the fixture up and do the wire connection. Attach the canopy over the mounting nipple and secure with a collar ring.
9. Dress the crystals as illustrated.

Note : All electrical components must be installed by a licensed electrician in accordance with the National Electric Code and the appropriate local electrical codes.

Crystorama.com

MODEL # 1157-PB-CL-MWP

ASSEMBLY INSTRUCTION

Crystal Sets

• A. 126 sets. (1)14mm * (1)ASg-2•
• B. 1 sets. (3)14mm (1)ASB-50mm aali
• C.ßSets_ (1)14mm (1)AS9-25
• D. 8 sets. (2) 14mm • ASg-2•
• E. 8 Piece. (8)14mm
• F. 16 Sets. (2)14mm + (1)Square + AS9-2.5″
• G. 8 Sets. (13)14mm
• H. 8 Sets. (8)14mmI. 8 Sets. (16)14mm
• J. 16 Sets. (21)14mm
• K. 8 Sets. (7)14mm + AS9-2.5″
• L. 8 Sets. (21)14mm
• M. 8 Sets. (9)14mm + (1)Square + (2)14mm + AS9-2.5″
• N. 8 Sets. (1)14mm + (1) 4pin 14mm + (5)14mm + AS9-2.5″
• O. 8 Sets. (20)14mm + (1)Square + （2）14mm + AS9-2.5″
• P. 16 Sets. (23)14mm
• Q. 8 Sets. (1)14mm + (1)Square + (4)14mm + AS9-

All electrical components must be installed by a licensed electrician in accordance with the National Electric Code and the appropriate local electrical codes.

You will need 20- Candelabra Base Bulb40 Watts recommended 40 Watts Max. USE LED BULBS FOR EXTENDED USE
The fixture is Damp rated

HOW TO INSTALL

Place the fixture parts on a soft cloth-covered platform before installation of the fixture.

1. To install the 6″arms, slightly loosen each screw on the metal plate. Pull a female plug through a hole in the upper metal plate. Connect the male plug at the end of the upper arm with the female plug that was just pulled. Push the end of the arm with the metal tab through the hole until stopped by the metal tab (this should also push the wires and plugs back inside the metal plate). Twist the metal tab counter-clockwise until both inserts lock onto the loose screws. Tighten the screw securing the arm in place. Repeat for all 6″arms
2. Repeat Step 1 for the 10″ and 15″ arms. The 10″ arms attaches on the middle tier and the 15″ arms attaches on the bottom-most tier.
3. Thread the threaded pipe into the coupling at the bottom of Center Column Kit 2 then place the glass vase, check ring, metal washer, bobeche, and metal washer in that order. Secure with the finial.
4. Screw the Center column kit 1 onto the center column kit 2.
5. Set the mounting hardware onto the beam.
6. Decide the desired hanging height and adjust the chain to the correct length.
7. Raise the fixture up and do the wire connection. Attach the canopy over the mounting nipple and secure with the collar ring
8. Dress the crystals as illustrated.

WARNING : This product can expose you to Lead, which is known to the State of California to cause cancer and/or birth defects or reproductive harm. For more information go to www.p65warnings.ca.gov

Part Numbers

• A.(1)-Mounting hardware
  Wire connector ×2.
  Lock washer ×4.
  Hex nut ×5.
  Nipple ×2.
  Screw ×4.
  Metal hickey x1.
  Cable wire+Fixed stud x1.

• B. (1)-Canopy (W5″xH1″)-XSN1155PBCAN5IN

• C. (1)-Collar Ring

• D. (1)-Collar Loop-XSN1155PBLOOP1

• E. (1)-Chain (5mmx72″)-XSN1156PBCHA5MM

• F. (1)-Center Column Kit Loop-XSN1155PBLOOP2

• G.(1)-Center Column Kit 1
  Top Bowl ; Ø6″,16pin,13mm center hole.
  Glass Vase; H8″
  Top Bobeche ; Ø4″, no pin,24mm center hole. -XSN1155BOB4IN
  Glass Vase; H6″
  Metal Cover ; H1.5″

• H (4)-6″ Arms with holder-XSN500GDARM6INKD

• I. (1)-Center Column Kit 2
  Glass Bowl ; Ø5″,0 pin,13mm center hole.
  Distributor Box-1;Ø4 5/8 ” ; 13mm center hole. with female plug.
  Glass Vase; H8″
  Glass Bowl ; Ø6″,8 pin,13mm center hole.
  Distributor Box-2;Ø5 1/2″ ;13mm center hole. with female plug.
  Glass Vase; H8″
  Glass Bowl ; Ø6″,8 pin,13mm center hole.
  Distributor Box-3;Ø5 1/2″, 13mm center hole. with female plug.

• J. (8)-10″ Arms with holder-XSN500GDARM10INKD

• K.(8)-15″ Arms with holder-XSN500GDARM15INKD

• L. (20)-Male Plug

• M.(21)-Bobeche; Ø4″,6 pin,24mm center hole.
  -XSN1157PBBOB6PN

• N. (20)-PVC Candle Sleeve

• O. (1)-Bottom Bowl ; Ø6″,8 pin,13mm center hole.

• P. (2)-Metal washer

• Q.(2)-Check Ring

• R. (1)-Coupling

• S. (1)-Glass Vase; H6″

• T. (1)-Thread

• U. (1)-Finial-XSN1155PBFIN

• V. (2)-Chain link

References

• Crystorama Lighting
• p65warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>