TAKSTAR WPM-400S Wireless In-Ear Monitoring Earphones User Manual

WPM-400S Wireless In-Ear Monitoring Earphones

VI I. Clear Pa iring:
Open the charging case lid when both earpieces are inside, press and hold the
case button for Ss u nti I the LED dots on both earphones light up for ls to clear the
pairing history.
VI II. Charge the Charging Case:

1. Wireless Charging:

WPM-400S/S R Wireless In-Ear Monitoring Earphones
Touch Control Descriotions
Call Notification Same as your phone’s ringtone.
Answer/End Call Tap the touch area on either earphone.
Reject Call Touch and hold the touch area on either earphone for l.Ss.
Music Play/Pause Tap the touch area on either earphone.
Previous Tack Double-tap the touch area on the left earphone.
NextTrack
Double-tap the touch area on the right earphone.
When using only one earphone, double-tap it switches to Next Song only.
Stereo/Single Take either or both earphones out, and they will auto
Mode Switch reconnect to form mono/stereo audio.
Auto Reconnect Activated when re-entering connection range within 3min.
Auto Play Auto resume playback interrupted by incoming call after call ends.
Voice Assistant Touch and hold the touch area on eitherearphonefor2s until
vou hear” Du” to activate assistant.
Low Power Prompt “Du” tone alert once every 5% battery level is lost when below 20%
until auto shutdown. (no prompt in Monitoring mode)
Battery Level Indicated by the meter aside the Bluetooth icon on the status
barofvourconnected smartphone (Android 8.1 or above)
VI. Pairing Method for One-To-Many Monitoring:
Multiple master devices Master and slave devices
(A& Bare both master device WPM-400S) (A is master device WPM-400S;
C is slave device WPM-400S R)
Set A to Monitoring mode, set B to TWS Set A to Monitoring mode, (C is already
mode, then place B’s earphones into A’s TWS mode), then place C’s earphones
charging case, and long press [Ml button into A’s chatngcase, and long press
for8s until the LED on earphones flashes [Ml button or8s until the LED on
ls to clear pairing history. Next, click [Ml ea rp hon es flashes ls to clear pairing
three times to pair. Follow the same steps history. Next, click [Ml three ti mes to
to pair each newsetofearphonesto pair. Follow the same steps to pair each
enable monitoring same content across newsetofearphones,indicatinJ
multiple devices. successful contact and charging starte .
If the earphones fai I to monitor, retry the If the earphones fail to monitor, retry the
afore steps. afore steps.
To reconnectthe earphones to B, place the To reconnect the earphones to C, place
earphones the earphones back in C charging case
back in B charging case and follow the afore and follow the afore similar steps.
similar steps.
Note: Slave device WPM-400S R is different from masterWPM-400S in that its charging
case can not serve as a transmitter.
fl
WPM-400S/S R Wireless In-Ear Monitoring Earphones
VI I. Clear Pa iring:
Open the charging case lid when both earpieces are inside, press and hold the
case button for Ss u nti I the LED dots on both earphones light up for ls to clear the
pairing history.
VI II. Charge the Charging Case:

1. Wireless Charging:
   i
   Wireless ChargingArea Please place the charging case in the
   center of the wire less charging area
   Note: To ensure normal functionality, please use a wireless charging device that
   meets Qi standard for charging.
2. Wired Charging:
   (1 I)
   Note: To ensure normal functionality, please use the supplied charging cable to
   connect the case with powersupplyforcharging.
   ~
   WPM-400S/S R Wireless In-Ear Monitoring Earphones
   II. Live Stream Monitoring:

• Illustrated model isTakstarMXl Pro Mixer
  o~··~o
  ~)9
  Headphone
  Interface
  ilU
  … .,
  Type-Cto3.5mm Cable
  Transmitter/ChargingCase

1. Use the audio adapter cable included, connectthe device with audio interface as
   shown in the above figure.
2. The first time you open the case lid, the device shows power level then enters
   Monitoring mode by default. Open the charging case, the right LED on the case turns
   blue permanently, take out the earphones to start monitoring.
3. The previously selected mode is retained in memory and called on next power-up.
   Ill. Switch TWS/Monitoring Mode:
4. Under Monitoring mode, place the earphones (either or both) into the charging
   case, then double-click the [Ml button to enterTWS mode, indicated by the right
   LED flashing blue.
5. UnderTWS mode, place the earphones (either or both) into the charging case,
   then double-click the [Ml button to enter Monitoring mode, indicated by the right
   LED staying blue. fl
   WPM-400S/S R Wireless In-Ear Monitoring Earphones
   IV. TWS Connection
   “‘ ” i
   ( (LqT) ) >)) ((< (c) 8 + ill
   <;) ~ 0 ~
   Charging Case Button
   Smartphone
6. The earphones start in Monitoring mode by factory defau It. To switch to TWS
   mode, place the earphones back in the charging case and double-click the [Ml
   button, the right LED on the case will flash to indicate TWS mode.
7. Turn on your phone, go to settings, enable wireless connection and search for
   a device named “TAKSTARWPM-400S/TAKSTAR WPM-400S R”, tap itto connect.
   V. SmartTouch Control:
   Touch Area ~II //~ Touch Area
   L R
   fl

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>