REELCRAFT A5806 OLP Spring Driven Hose Reels Instruction Manual
- June 14, 2024
- REELCRAFT
Table of Contents
REELCRAFT A5806 OLP Spring Driven Hose Reels
Low and Medium Pressure Model Numbers: A5806 OLP A5835 OLP A5850 OLP A5835 OMP
Dimensions
SAFETY
- Do not use reel at higher pressures or temperatures than listed on the back of this bulletin.
- Remove all spring tension before beginning disassembly process.
INSTALLATION
A flexible hose connection must be used between the hose reel inlet and the
source of supply to prevent possible misalignment and binding.
MOUNTING
The hose reel is equipped with a universal mounting bracket so that it can be
mounted on the floor, wall or ceiling; whichever place is convenient. The hose
guide arm can be moved to the position desired by removing
the screws fastening the guide bracket to the reel base. Shift the guide arm
bracket so the hose comes off the reel at the desired position and replace the
screws. NOTE: For proper installation in wall mount applications, ensure reel
is mounted with inlet on the right as you are facing the reel. Failing to do
so could cause latching issues.
LUBRICATION
Hose reel spring and bearings are factory lubricated and require no further
lubrication.
REPLACING HOSE
- Wind spool flange clockwise-facing swivel-until spring is tight.
- Back off three turns and latch.
- Insert hose through roller guide.
- Connect hose fitting to swivel joint and secure hose with clamps.
ADJUSTMENTS
To adjust spring tension, add or remove wraps of hose from the spool, one
wrap at a time until desired tension is obtained.
REPAIRS
Extensive repairs should be performed only by an authorized serviceman or
factory to avoid damage which may void your warranty. Remove all spring
tension before beginning disassembly process.
Operating Instructions
Item #| Part #| # Req.| Description| Item #| **Part
| # Req.| Description| Item #| Part #| # Req.**|
Description
---|---|---|---|---|---|---|---|---|---|---|---
1| 300031| 2| 1” Snap Ring| 15| 300006| 1| 3/8-16 x 1/2” Set Screw| 21|
400018| 1| Latch Spring
2| 300034| 2| Spacing Washer| 16| 600094| 1| Spring Case & Hub Ass’y| 22|
400020| 1| O-Ring
5| 260149| 1| Reel Flange| 17| 600050| 1| Drive Spring Assembly| 23| S400109|
1| Latch Plate Assembly
7| 260151| 1| Sheave Disk| 18| 600029| 1| Base Assembly| 24| 3-117440| 1|
U-Bolt Hose Clamp
8| 500019| 1| Latch Cam| 19| 400021| 1| Latch Bumper| 26| 261650-1| 2| 1/4-20
Nyloc Nut
14| 261360| 1| Spring Case Stud| 20| 400012| 1| Latch Bushing| 31| S82-15| 9|
Nyloc Nut 10-32 x 3/8”
Item #| Description| # Req.| A5835 OLP| A5806 OLP| A5850 OLP| A5835 OMP
---|---|---|---|---|---|---
3| Hex Screw| 3| S295-102| S2-48| S2-48| S295-102
4| Lockwasher| 3| None| 902016| 902016| None
6| Spacer| 1| None| 260445| 260445| None
9| Spring Arbor| 1| 260648| 400017| 400017| 260648
10| Bumper Stop Assembly| 1| 2-HR1004-3| None| 2-HR1004-3| 2-HR1004-3
11| Hose Ass’y| 1| 601021-35| None| 601022-50| 37-260043
12| Guide Arm Assembly| 1| 500107| 600247| 600247| 500107
27| Main Shaft| 1| 500008| 261240| 261240| 500008
28| Swivel Assembly| 1| S600915-1| S600920-1| S600920-1| 602032
29| 90° Elbow| 1| 300010| 300010| 300010| S257-26
30| 90° Elbow| 1| 300010| 300010| 300010| S257-26
Hose I.D. and Length| 1/2” x 35’| None| 1/2” x 50’| 1/2” x 35’
Reel Inlet Connection| 3/8” F.P.T.| 3/8” F.P.T.| 3/8” F.P.T.| 3/8” F.P.T.
Max. Operating Pressure| 300 P.S.I.| 500 P.S.I.| 300 P.S.I.| 2000 P.S.I.
Max. Operating Temperature| 150 °F| 210 °F| 150 °F| 210 °F
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>