MAXVIEW ANTMINI Mini 5G or 4G 2×2 MIMO Antenna Instruction Manual

June 12, 2024
MAXVIEW

MAXVIEW ANTMINI Mini 5G or 4G 2×2 MIMO Antenna

MAXVIEW ANTMINI Mini 5G or 4G 2x2 MIMO Antenna-product

Product Information Product Name: ANTMINI Mini 5G/4G 2X2 MIMO Antenna

Manufacturer: Maxview Ltd

Contact Information:

Specifications:

  • Antenna Type: Omni-directional
  • Frequency/Gain: 698-6000 MHz/5.9dBi-8.8dBi
  • Connector Type: 2 x SMA
  • Impedance: 50 Ohm
  • Power: Passive
  • Cable Lengths: 0.8m as standard
  • Housing: Aluminium Base, UV Stable ASA Cover
  • Dimensions: H: 67mm x W: 180mm x D: 60mm
  • Weight: 385g

Product Contents:

  • A. Omni-directional Roof Mount Antenna and 0.8m cables with SMA connectors
  • B. Roof Clamp
  • C. No. 6 Screws (spares included)
  • D. Fixing Template
  • E. SMA to TS9 Adaptor X 2

Accessories (Sold Separately):

  • Bracket Fixing Kit – For roof mounting (MXL060/KIT or MXL060/GKIT)
  • Weatherproof Socket with SMA Connectors (B2016)
  • Roam Extension Cables (MXL050/EXT1, MXL050/EXT2, MXL050/EXT3, or MXL050/EXT5)
  • Thread Extender (MXL050/TE)

Product Usage Instructions Positioning your Antenna:

For best performance, it is recommended to mount the router in close proximity to the roof-mounted antenna. Avoid using extension cables longer than necessary.

Mount the antenna on a horizontal flat roof, leaving a 30cm gap from obstacles around it to avoid interference issues.

Important Antenna Installation Information:

Follow the provided installation instructions for positioning and fitting the antenna.

Fitting the Antenna:

Use the provided roof clamp and screws to securely attach the antenna to your roof.

Ensure that the antenna is mounted in a suitable location, following the guidelines mentioned in the positioning instructions.

Introduction

Thank you for purchasing this product, should you have any difficulty using your Antenna please contact our friendly Customer Helpline on +44 (0)1553 811000 or email support@maxview.co.uk.

Product Contents

  • A. Omni-directional Roof Mount Antenna and 0.8m cables with SMA connectors
  • B. Roof Clamp
  • C. No. 6 Screws (spares included)
  • D. Fixing Template
  • E. SMA to TS9 Adaptor X 2

Tools required

  • – Power Drill
    – 2.5mm Drill Bit

  • – 25mm Hole Saw
    – Cross Head Screwdriver

  • – Hack Saw
    – File/Emery Paper

  • – Surface Cleaner

Specifications

Antenna

  • Type: Omni-directional 2×2 MIMO (multiple in multiple out)
  • Frequency/Gain: 698-6000 MHz/5.9dBi-8.8dBi. Includes all 3G, 4G and 5G frequencies
  • Connector Type: 2 x SMA
  • Impedance: 50 Ohm
  • Power: Passive
  • Cable Lengths: 0.8m as standard
  • Housing: Aluminium Base. UV Stable ASA Cover
  • Dimensions: H: 67mm x W: 180mm x D: 60mm
  • Weight: 385g

Accessories

Sold separately

Bracket Fixing Kit – For roof mounting
The raiser bracket allows you the flexibility to mount your antenna anywhere on your roof and enter the cable at your preferred point using the supplied cable entry cover. Alternatively you may have an existing cable entry point you may like to utilise instead. Designed and manufactured specifically for the Antenna, the aluminium bracket is lightweight, strong and finished with a durable white or black powder coating. Suitable for any flat roof the kit also includes 3m extension cables for flexible mounting position.

MXL060/KIT White
MXL060/GKIT Black

Roam Extension Cables
Extension cables can be purchased separately to allow a flexible mounting position to the router.

  • 1 metre MXL050/EXT1
  • 2 metres MXL050/EXT2
  • 3 metres MXL050/EXT3
  • 5 metres MXL050/EXT5

Weatherproof Socket with SMA Connectors

The Weatherproof Socket provides an external entry point into the side of any vehicle. Available with 2 SMA connections, making it ideal when using the Roam Antenna with the Roam Bracket Fixing Kit (See left) to allow for a temporary connection or
where entry into the roof is not possible. It can also be used for other applications where an external SMA connection is required.

B2016

Thread Extender
Can be used to fit all Roam Antennas to thicker vehicle roofs. For example American RV’s, Winterised Motorhomes, and Over Landing vehicles. Thread Extender is ideal for roofs 50 – 90mm thick.

MXL050/TE.

Positioning your Antenna

Distance between Router and Antenna
For best performance, we recommend mounting the router in close proximity to the roof-mounted antenna. For best performance, do not use extension cables that are no longer than necessary.

Roof Antenna Position
We recommend leaving 30cm gap from obstacles around the antenna to avoid interference issues and mounting on a horizontal flat roof.

Important Antenna Installation Information

  1. The 3M seal provides a permanent installation. The adhesive is extremely strong and the antenna is not designed to be removed. Please ensure you are completely happy with your antenna’s position and orientation before installation.

  2. The Mini Antenna is designed to be mounted directly to a horizontal, flat and smooth surface such as GRP (Glass Reinforced Plastic) with the coaxial cables passing directly through the roof underneath the centre of the antenna. The standard installation is designed for roof thicknesses from 10mm up to 50mm.

Fitting the Antenna

  1. Once you have a suitable position for the antenna, cut out the supplied template. Use to mark the 25mm centre hole position and mark the outside of the antenna.

  2. At the marked centre position, drill a 2.5mm pilot hole through the roof. Use a 25mm hole saw to drill out the centre hole through the roof.
    Tidy up the hole to remove swarf and sharp edges.
    MAXVIEW ANTMINI Mini 5G or 4G 2x2 MIMO Antenna-fig9

  3. Use the Antenna clamp to gauge the depth of the roof. The best way to do this is to sit the Antenna clamp upside down through the hole. Then, from the inside, mark on the clamp where the clamp passes through the ceiling and into the vehicle.
    3A. Please Note. Alternative Nut and Washer option for thin metal roof applications is supplied. If this is better suited for your application ignore step 3 & 4.

  4. Remove the clamp and cut the clamp shaft to the correct length. The correct length for your installation will be the roof depth minus 3mm. This will ensure the clamp does not bottom out on the antenna when tightened.
    E.g. If roof depth is 30mm. The clamp shaft should be cut 27mm along the shaft.
    MAXVIEW ANTMINI Mini 5G or 4G 2x2 MIMO Antenna-fig10

  5. Clean the surface where the antenna will be installed, ensuring it is free from debris and grease.

  6. Pass the cables through the hole and remove the self-adhesive backing from the 3M seal. Pass the cables through the roof and position the antenna making sure it’s facing the front of the vehicle -Please reference Picture 7 below.MAXVIEW ANTMINI Mini 5G or 4G 2x2 MIMO Antenna-fig12
    IMPORTANT – Ensure the position of the antenna is central to your markings, as once stuck down, the antenna is not designed to be removed.

  7. Press firmly around the edges of the antenna to ensure a watertight seal has been achieved.

  8. From the inside of the vehicle, attach the clamp and turn clockwise onto the thread protruding from the bottom of the antenna. Continue to turn until the clamp is compressing the seal underneath the antenna. Once in position, use 1 x No.6 Screw to secure the clamp in position.MAXVIEW ANTMINI Mini 5G or 4G 2x2 MIMO Antenna-fig13
    8A. If using the Nut and Washer Option (ref page 5) please tighten and secure using a 27mm Spanner.

  9. The Antenna is now installed and ready to be connected to a suitable 4G/5G Router.

General Safety Warnings

Read these instructions carefully and become familiar with your Maxview product. Understand the application, limitations and any hazards involved with the installation and operation. Failure to follow all instructions may result in damage to your vehicle and/or serious injury. Maxview declines all responsibility in the event of incident or accident if they are due to a non observation of the installation instructions or the way the product is used.
No modifications to the product are permissible.

Installation

  • Always consider the additional height the product you install adds to the vehicle
  • Always follow manufacturer’s operating instructions before using tools and equipment.
  • Take care when working at heights. Keep work area clean and tidy to avoid trip hazards
  • Use creeper boards where necessary to ensure roof construction can support your weight
  • All electrical work should be carried out by a competent person

Operation

The maximum speed of vehicle with product mounted on roof is 81mph (130km/h)

Servicing & Support

  • Any inspection or repair must be carried out by Maxview or an appointed representative of the manufacturer
  • No regular maintenance required on the product
  • Do not dismantle product
  • Do not use solvent or abrasive cleaning agents on the product
  • Only use a suitable mild detergent to clean the product
  • Do not pressure wash the product
  • We recommend you check the mechanical integrity of a roof mounted product at least once a year
  • If in the event that you do experience a problem with the product, call Maxview Customer Service + 44 (0)1553 811000

Maintenance

The antenna has been designed to be maintenance and trouble free. For optimum signal strength, keep the cover clean from dirt, bugs, and other debris. Periodic washing of the top cover with mild soap and water is recommended.

  1. Do not remove the cover of the antenna as it will void the limited guarantee.
  2. Never power wash the antenna. Keep the enclosure clean from dirt, bugs, and other debris by hand washing with mild soap and water.
    DO NOT USE SOLVENTS TO CLEAN THE ROAM. DO NOT DROP OR EXPOSE TO JARRING MOVEMENTS.

Terms and conditions

In no event shall Maxview be liable for any indirect, incidental or consequential damages from the sale or use of the product. This disclaimer applies both during and after terms of the guarantee. This does not affect your statutory rights. The antenna is designed for permanent installation and is not designed to be removed or serviced. Whether the antenna is in warranty or not and whether the cause for removal is our fault or not, we are not responsible for the safe removal of the antenna. We will not be held responsible or liable for any damage done to the antenna or other property whilst removing the antenna, regardless of the reason for removal.

2 year guarantee

Every Maxview Antenna is covered by the following 2 year parts limited guarantee from the date of original purchase.

How do I claim on my guarantee?
In the unlikely event that you have an issue with your product please contact our Customer Services Team on +44 (0) 1553 811000 or email support@maxview.co.uk. You will need to retain your proof of purchase.
In no event shall Maxview be liable for any indirect, incidental or consequential damages from the sale or use of the product. This disclaimer applies both during and after terms of the guarantee. This does not affect your statutory rights.
Due to expanding and changing telecommunications market, Maxview cannot be held responsible for changes made to communication services. Software updates to address such issues are not covered under guarantee.

Terms and Conditions of the Guarantee

  • a) Your guarantee starts from the date you purchased your item. Your guarantee will be valid from date of manufacture if you are unable to provide a proof of purchase.

  • b) A guarantee authorisation must be obtained from Maxview prior to work commencing.

  • c) Maxview is responsible for the cost of a replacement part if the original part is determined to be defective under the terms of the guarantee.

  • d) Any replacement parts required will be supplied, by return, on receipt of the faulty part.

  • e) Any work requiring replacement parts will only be sanctioned on receipt of proof of the broken part.
    The customer is responsible for the cost of replacement parts after the guarantee period has expired.

  • f) Our guarantee is “Back To Base.” No travelling costs will be paid.

  • g) Parts that suffer breakdown and/or failure due to flooding/water ingress or abrasive cleaning caused by solutions and/or Pressure Washers are not covered under our guarantee.

  • h) Our guarantee does not cover installation or external wiring.

This guarantee also does not apply where:

  • The product has been abused, misused, improperly installed or improperly maintained.
  • The product has been installed without the use of a Maxview mounting bracket designed for the product.
  • Repairs have been made or attempted by others that are not certified by Maxview to do such repairs.
  • Repairs are required because of normal wear and tear.
  • Alterations have been made to the product.
  • The antenna unit has been opened without authorisation.
  • Damage has been caused by power washing.
  • Circumstances beyond the control of Maxview cause the product to no longer operate correctly.
  • Customer is not the original owner.

Certification and Environment

  • The Antenna has been designed, constructed and marketed in compliance with the safety and product requirements of the relevant EEC Directives.
  • Products marked with the crossed out wheely bin must not be disposed of with normal household waste but made available for separate household collection. Separate collection of used products and their packaging allows materials to be recycled and used again. Re use of recycled materials helps prevent environmental pollution and reduces the demand for raw materials.
  • UK Conformity Assessed (UKCA) marking is a certification mark that indicates conformity with the applicable requirements for products sold within Great Britain.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

MAXVIEW User Manuals

Related Manuals