LNC FRAIAQHD14329K7 Modern Brass Gold 2-Light Candlestick Vanity Light Instruction Manual
- June 12, 2024
- LNC
Table of Contents
FRAIAQHD14329K7 Modern Brass Gold 2-Light Candlestick Vanity Light
Product Information
- Item Number: FRAIAQHD14329K7
- Maximum wattage: 40W per bulb
- Voltage: 120V
- Parts included: Green ground screw (1), Mounting plate (1), Back plate (1), Ball knob (2), Glass (2), Socket (2), Screw (6), Tube (1)
- Accessories enclosed: Mounting screw (2), Plastic wire connector (3)
Product Usage Instructions
- Before starting, turn off the electricity by placing the main power switch in the OFF position at the main fuse or circuit breaker box, and place the wall switch in the OFF position.
- Make sure the mounting surface is clean, dry, flat, strong enough, and 1/4 larger than the canopy on all sides. Correct any gaps between the mounting surface and canopy exceeding 3/16 as required.
- Make sure the ceiling or wall can stand the weight of the lamp before installation.
- When replacing bulbs, turn off or unplug the lamp and wait until it is cool as bulbs get hot quickly.
- Assembly and installation instructions:
- Carefully remove the fixture from the carton and check that all parts and accessories are included.
- Turn off the power by placing the main power switch in the OFF position at the main fuse or circuit breaker box, and place the wall switch in the OFF position.
- To make assembly, unscrew ball knobs (F) from back plate (E) then gently remove mounting plate (D).
- Secure mounting plate (D) to the outlet box with mounting screws (A).
- Make wire connections according to the chart provided. Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
- Align the holes in back plate (E) with the preassembled mounting screws, then attach back plate (E) to mounting plate (D) with the previously removed ball knobs (F). Hand tighten until snug.
- If you are not experienced with electrical work, we suggest installation by a licensed electrician.
Item Number: FRAIAQHD14329K7
WARNING (To reduce the risk of fire, electric shock, or personal injury):
- We suggest installation by a licensed electrician.
- Please read the instruction carefully and save it as you may need it at a later time.
- Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
- A) Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
- B) Place the wall switch in the “OFF” position.
- Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
- Make sure that the ceiling or wall can stand the weight of the lamp before installation.
- Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.
- Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
- When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
- The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT
TOOLS REQUIRED (NOT INCLUDED)
Before starting assembly and installation please prepare the needed tools as below picture
PARTS INCLUDING
(C) Green ground screw (1)
(D) Mounting plate (1)
(E) Back plate (1)
(F) Ball knob (2)
(G) Glass (2)
(H) Socket (2)
(I) Screw (6)
(J) Tube (1)
ACCESSORIES ENCLOSED
A) Mounting screw (2)
B) Plastic wire connector (3)
ASSEMBLY & INSTALLATION INSTRUCTIONS:
-
Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
-
Turn off power
Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.- A) Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
- B) Place the wall switch in the “OFF” position.
-
Make assembly
Step A1: Unscrew ball knobs (F) from back plate (E) then gently remove
mounting plate (D).
Step A2: Secure mounting plate (D) to the outlet box with mounting screws
(A).
Step A3: Make wire connections
Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS
BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Twist wires together with plastic wire connectors until tightly joined, and
wrap each connector with approved electrical tape. Be sure that no wire
strands are exposed and then carefully tuck all wires into the outlet box.
Step A4: Align the holes in back plate (E) with the pre-assembled
mounting screws, then attach back plate (E) to mounting plate (D) with the
previously removed ball knobs (F). Hand tighten until snug.
NOTE: back plate (E) should be snug against the wall with ball knobs (F). If not, remove back plate (E), adjust the threaded length of pre-assembled mounting screws on mounting plate assembly (D) by unscrewing the pre-assembled hex nuts and then screwing the pre-assembled mounting screws in or out of mounting plate (D) until the secure length is achieved. Tighten the pre- assembled hex nuts and back to Step A4.
Step A5: Install bulbs (Not included. Please do not exceed the maximum wattage recommended on the socket.) Place glass (G) on sockets (H) and secure them with screws (I).
Check everything is installed properly, then you could turn on the light. Enjoy!
CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner
(such as mild and non abrasive soap). Do not use abrasive materials such as
scouring pads or powders, steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement
parts. All parts for this fixture can be ordered from the place of purchase.
Be sure to use exact wording from illustration when ordering parts.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>