Holybro Kopis X8 Cinelifter 5 Ducted

Assembly Guide

Part List

• 510204 Upper Plate

• 510205 Lower Plate With 9 Pressure riveting nut

• 510213 Arm 4pcs

• 510210 Bottom Support Plate

• 510207 Bottom Plate

• 510214 Reinforcement Arm 4pcs

• 510206 Top Reinforcement Plate 4pcs

• 510215 Motor Holder 8pcs

• 510208 Bottom Reinforcement Plate 4pcs

• 510155 Camera Mounting Plate

• 510212 Side Support Plate R

• 510211 Side Support Plate L

• 510209 Top Plate

• 31117 TPU 3D print set 17pcs

• FPV Camera Mount
• GPS Holder
• Antenna Holder
• SMA Antenna Mount L
• SMA Antenna Mount R
• Positioning Sleeve 8pcs
• Landing Gear 4pcs
• Gummie M8 9pcs
• Gummie M3 8pcs
• Nylon Standoff M3*5 4pcs
• Screw M3*10 10pcs
• Screw M3*8 50pcs
• Screw M3*16 4pcs
• Hand Screw M3*8 2pcs
• Locknut M2 4pcs
• Screw M3*35 4pcs
• Locknut M3 17pcs
• Flat Head Screw M3*8 4pcs
• Socket Cap Screw M3*5 34pcs
• Screw M2*14 4pcs
• Metal Stud M3*16 22pcs
• Screw M3*12 26pcs
• Aluminum Standoffs M3*37.5 34pcs
• Aluminum Standoffs M3*100 4pcs
• Aluminum Standoffs M3*60 4pcs

Product Usage Instructions

1. Before assembly, please make sure to check the orientation of the parts.
2. Attach the Reinforcement Arm (2) to the Upper Plate (3), making sure the side with grooves is facing downwards.
3. Attach the Arm (4) to the Reinforcement Arm (2).
4. Attach the Bottom Plate (5) with the pressure riveting nut to the Arm (4).
5. Attach the Bottom Reinforcement Plate (8) to the Bottom Plate (5).
6. Attach the Motor Holder (15) to the Bottom Reinforcement Plate (8).
7. Attach the Aluminum Standoffs (7) to the Motor Holder (15) using blue Threadlocker on the metal studs (10).
8. Attach the Gummie M3 (8) and Locknut M3 (9) to the Aluminum Standoffs (7).
9. Attach the Metal Stud (10) to the Locknut M3 (9).
10. Attach the Nylon Standoff M3*5 (11) to the Metal Stud (10).
11. Attach the Side Support Plate R (12) and Side Support Plate L (13) to the Upper Plate (3).
12. Attach the Top Reinforcement Plate (6) to the Upper Plate (3).
13. Attach the Camera Mounting Plate (1) to the Top Reinforcement Plate (6).
14. Attach the SMA Antenna Mount L (19), SMA Antenna Mount R (20), and GPS Holder (41) to the Top Plate (18).
15. Attach the Positioning Sleeve (27) to the Top Plate (18).
16. Attach the Injection Molded Duct (29) to the Bottom Reinforcement Plate (8).
17. Attach the Landing Gear (38) to the Bottom Reinforcement Plate (8).
18. Attach the Battery Pad (35) and Bottom Reinforcement Plate (36) to the Bottom Plate (33).
19. Attach the Carbon Fiber Tube (37) to the Bottom Reinforcement Plate (36).
20. Attach the Antenna Holder (39) to the Top Reinforcement Plate (6).
21. Install propellers with proper direction.
22. Use zipties as a backup to secure heavy loads.

PART LIST

#31117 TPU 3D print set 17pcs

Usages Instructions

www.holybro.com

References

• Holybro - Build your drone from here – Holybro Store

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>