StarTech USB3SDOCKHD Laptop Docking Station User Manual

StarTech USB3SDOCKHD Laptop Docking Station

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Use of Trademarks, Registered Trademarks, and Other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. Regardless of any direct acknowledgment elsewhere in the body of this document, StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.

Introduction

Packaging Contents

• 1 x Docking Station
• 1 x 0.9m USB 3.0 Cable
• 1 x Universal Power Adapter (NA/UK/EU)
• 1 x Installation CD
• 1 x Instruction Manual

System Requirements

• USB 3.0 enabled computer system with available USB 3.0 port
• Available AC electrical outlet
• HDMI® (and either DVI-D or VGA if the dual display is desired) enabled display device(s) e. g. monitor, projector, HTDV, etc. with cables

Rear View

Side Views

1. DVI-D Port
2. HDMI Port
3. VGA Port
4. 10/100/1000Mbps LAN (RJ-45) Port
5. Headphone Port
6. Microphone Port
7. USB 3.0 Downstream Port
8. Security Lock Hole
9. USB 3.0 Upstream Port
10. DC IN Port

Installation

1. Connect the included power adapter from an AC electrical outlet to the USB Docking Station.

2. Insert the provided Driver CD into the computer’s CD/ DVD drive.

3. Autorun should give you the option to run the Setup.exe application.
   If Autorun does not start, Go into “My Computer” double-click the CD/DVD drive that the CD is in and run the Setup.exe application.

4. Run the “setup.exe” file on the CD to launch the driver installation program. Follow the on-screen instructions to complete the driver installation.

5. Please wait while the installation program copies the necessary files.

6. Connect the Docking Station to the computer using the included USB 3.0 cable. Windows will automatically detect and install the drivers.

7. Connect the monitor(s) to the USB Docking Station using HDMI, DVI-D, or VGA cables and power on the monitors. Please choose the dual output connection combination as either:

   • HDMI + DVI
   • VGA + HDMI
     NOTE: Please do not connect monitors to the VGA, DVI-D, and HDMI ports simultaneously. It can cause unexpected errors in your monitor configuration.

8. Windows will start to automatically load the drivers and software for the USB display adapter. Once complete, you should see this icon in your System Tray:

Verifying Installation

1. Open the Device Manager by right-clicking on Computer, and then select Manage.
   In the new Computer Management window, select Device Manager from the left window panel (For Windows 8, open the Control Panel and select
   Device Manager).
   Expand the “Network adapters”, “Sound, video and game controllers” and “Universal Serial Bus controllers” sections. On a successful install, you should see the following devices installed with no exclamation points or question marks.

Installing the Drivers

1. Please insert the Driver CD into your computer’s CD-ROM or DVD drive.
2. Click Setup.exe.
3. Select your language and click “I Accept”.
4. Wait until the drivers are installed successfully on your computer.
   NOTE: Please ensure that you install the drivers before connecting the docking station to your computer.

How to Use

Configuring the image being displayed by the monitor that is connected to the USB 3.0 Docking Station, can be done in one of two ways:

1. Accessing the Windows Display Settings

   • Windows XP/Server 2003: right-click on a blank area of the desktop, select Properties, then click on the Settings tab:

   • Windows Vista: right-click on a blank area of the desktop, select Personalize, then select the Display Settings option.
     

   • Windows 8/7/Server 2008 R2: right-click on a blank area of the desktop, select Screen Resolution.
     

2. Right-clicking the DisplayLink tray icon in the system notification area.
   

Display Modes

• “Extend” Display Mode (DEFAULT)
  The default display mode; this mode allows the output on the USB 3.0 Docking Station to work as an “Extended” display to the on-board display (i.e. internal graphics card). This extended working space improves work efficiency.
  You may change the relative position of this extended display through the Windows Display Settings or the “Extend To” option in the DisplayLink icon menu.

• “Extend To” Options
  When using the “Extend” display mode, 4 options are available for placement of the extended display, relative to the primary display: Left, Right, Above, Below. More fine adjustments to the placement of the extended display can be made through the Windows Display Settings.

• “Mirror” Display Mode
  This mode allows the same content from the on-board display to be duplicated (mirroring) to the output on the USB 3.0 Docking Station. The screen resolution setting on the USB 3.0 Docking Station video output will match the onboard display’s resolution. For example, if the onboard display’s resolution is 1024 x 768*32-bit, then the USB 3.0 Docking Station will use the same resolution.

• “Set as Main Monitor” Display Mode
  A unique feature to allow the USB 3.0 Docking Station to act as the main working display. The USB 3.0 Docking Station will work as the main graphics adapter on the system, while the onboard display will work as the extended display.
  Please be advised that some display utilities and drivers that shipped with certain AGP and built-in display adapters may prevent this option from working on some systems. You may be able to disable the other utility program (usually found in the same toolbar located in the bottom right-hand corner) to make this function work properly.

• “Off” Display Mode
  This option disables the video output from the USB 3.0 Docking Station.

• Screen Resolution
  Select the desired video display resolution for the connected monitor in Extend Mode. The default resolution setting is: 1024 x 768 * 32-bit.

• Screen Rotation
  4 options are available: 0°(Normal), 90° (Left), 180° (Upside-Down), 270° (Right) when used with the Extended or Primary display modes. It is a useful function for some rotatable display devices.
  

• Notebook Monitor Off
  Turns the monitor on the USB Docking Station to the main display and turns off the screen of the laptop. NOTE: This function works only when one add-on monitor is connected. This option will also only appear on laptop.

• Optimize For Video (Windows Vista / and later)
  Optimize video playback when using Windows Vista/ and later. Regular text may appear blurry while this is enabled.

Fit TV

When using Extended Mode, if the Windows Desktop screen is not completely visible on the TV/Monitor, this option can be used to adjust the size of the Windows Desktop.
NOTE: This mode will only work while using Extended mode. If using Mirror mode, this will automatically change the adapter to Extended mode. This mode cannot be used at the same time as the Screen Rotation feature.
A red border will appear on the Extended screen that will show the size of the new Windows Desktop. Use the horizontal and vertical + and – buttons to manually adjust the size to properly fit the screen.
NOTE: Holding the CTRL key while making adjustments allow for finer control.

Supported Video Resolutions

Resolution|

| Refresh Rate
---|---|---
640 x 480| | 60/ 72/ 75/ 85 Hz
800 x 600| | 56/ 60/ 72/ 75/ 85 Hz
1024 x 768| | 60/ 70/ 75/ 85 Hz
1280 x 720| | 60 Hz
1280 x 768| | 60/ 75/ 85 Hz
1280 x 800| | 60 Hz
1280 x 1024| | 60/ 75 Hz
1366 x 768| | 60 Hz
1400 x 1050| | 60/ 75/ 85 Hz
1600 x 1200| | 60 Hz
1680 x 1050| | 60 Hz
1920 x 1080| | 60 Hz
1920 x 1200| | 60 Hz
2048 x 1152| | 60 Hz

Inferred Modes

Some modes in the DisplayLink GUI are shown with [ ] around them. This occurs when connecting a monitor with a preferred mode (native resolution) higher than the maximum supported resolution of the DisplayLink device. In cases where the preferred resolution of the monitor cannot be supported, lower resolutions of the same aspect ratio are suggested in brackets. As these are inferred modes from the preferred mode of the monitor, they are not guaranteed to work with the display.

Troubleshooting

Minor display issues can generally be resolved by:

• Unplugging and re-plugging the DisplayLink device,
• Changing the display mode via the DisplayLink GUI or via Windows Display Properties

Error Messages

Message Description

Insufficient system resources exist to complete the requested service

| This can occur when entering extend mode with low system resources. The PC does not have enough memory (RAM) to start an extend display.

Close down any unused applications. The situation may also be improved by rebooting the PC.

The requested allocation size was too large| This can occur if trying to mirror a primary display with a resolution above 2300×1700 (4:3) or 2600×1500 (16:9).

Incompatible Display Driver

| This message will appear if the primary graphics card drivers installed are not WDDM compatible. Windows 7 is not designed to operate without WDDM drivers.

Download and install the latest Windows 7 (WDDM) drivers for your primary graphics card.

The system cannot write to the specified device

| This warning may be displayed in Windows XP after changing the display mode several times (e.g. Extend/ Dock mode) from the DisplayLink GUI. If this happens, detach and reattach the device to restore normal operation.

Specifications

Chipset

| DisplayLink – DL-3900 Genesys – GL3520 Realtek – RTL8211E

Connectors

| 2 x 3.5 mm Mini-Jack (3 Position) Female

1 x DVI-D (25 pin) Female

1 x HDMI (19 pin) Female 1 x RJ-45 Female

1 x VGA (15 pin; High Density D-Sub) 3 x USB 3.0 type A Female

1 x USB 3.0 type B Female

Maximum Data Transfer Rate| USB 3.0: 5 Gbps

LAN: 2 Gbps (Full-Duplex)

Supported Standards| IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, USB 3.0
Supported Network Link Speeds| 10/ 100/ 1000 Mbps
Ethernet Full Duplex Support| Yes
Auto MDIX| Yes

Maximum Video Resolution

| 2048 x 1152 (VGA)

1920×1200 (DVI-D)

1920×1080 (HDMI)

Audio Support| Yes (2-Channel Stereo, Mic)
Power Adapter| 5V DC, 4000mA, Center Positive
Enclosure Material| Plastic
Operating Temperature| 0°C to 40°C (32°F to 104°F)
Storage Temperature| -10°C to 60°C (14°F to 140°F)
Dimensions| 263 x 87 x 34 mm
Weight| 289g

Compatible Operating Systems

| Windows® 8 / 8.1 (32/64bit), 7 (32/64), Vista (32/64), XP SP3 (32), Mac OS® 10.6 and up

(Tested up to 10.9)

Technical Support

StarTech.com lifetime technical support is an integral part of our commitment to providing industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads

Warranty Information

This product is backed by a two-year warranty. In addition, StarTech.com warrants its products against defects in materials and workmanship for the periods noted, following the initial date of purchase. During this period, the products may be returned for repair, or replacement with equivalent products at our discretion. The warranty covers parts and labor costs only. StarTech.com does not warrant its products from defects or damages arising from misuse, abuse, alteration, or normal wear and tear.

Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to the products you need in no time.

Visit www.startech.com for complete information on all StarTech.com products and to access exclusive resources and time-saving tools. StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology parts. StarTech.com was founded in 1985 and has operations in the United States, Canada, the United Kingdom, and Taiwan servicing a worldwide market.

FAQ’s

What is the StarTech USB3SDOCKHD Laptop Docking Station?

The StarTech USB3SDOCKHD Laptop Docking Station is a device that allows you to connect your laptop to multiple peripherals and expand its capabilities. It provides various ports and features to enhance your productivity and convenience.

What are the key features of the StarTech USB3SDOCKHD Laptop Docking Station?

The key features of the StarTech USB3SDOCKHD Laptop Docking Station include support for USB 3.0 connectivity, dual video outputs (HDMI and DVI), audio input and output ports, Ethernet port, USB charging port, and a variety of USB ports for connecting peripherals.

What types of laptops are compatible with the StarTech USB3SDOCKHD Laptop Docking Station?

The StarTech USB3SDOCKHD Laptop Docking Station is compatible with most Windows and Mac laptops that have a USB 3.0 port. However, it is always recommended to check the product specifications and compatibility list provided by the manufacturer.

How does the dual video output feature work on the StarTech USB3SDOCKHD Laptop Docking Station?

The dual video output feature allows you to connect two external displays to your laptop simultaneously. You can connect one display using the HDMI port and the other using the DVI port, enabling you to extend your desktop or mirror your laptop's screen.

Can I charge my laptop using the StarTech USB3SDOCKHD Laptop Docking Station?

No, the StarTech USB3SDOCKHD Laptop Docking Station does not have the capability to charge laptops. It does, however, have a USB charging port that can be used to charge other USB-powered devices, such as smartphones or tablets.

What are the audio input and output ports used for on the StarTech USB3SDOCKHD Laptop Docking Station?

The audio input and output ports allow you to connect external speakers, headphones, or a microphone to your docking station. This enables you to have enhanced audio capabilities while using your laptop with the docking station.

How fast are the USB 3.0 ports on the StarTech USB3SDOCKHD Laptop Docking Station?

The USB 3.0 ports on the StarTech USB3SDOCKHD Laptop Docking Station provide data transfer speeds of up to 5 Gbps. This allows for fast and efficient file transfers between your laptop and connected USB devices.

Does the StarTech USB3SDOCKHD Laptop Docking Station support Gigabit Ethernet?

Yes, the StarTech USB3SDOCKHD Laptop Docking Station has a Gigabit Ethernet port, which supports high-speed wired network connections. This allows for reliable and fast internet connectivity when connected to a compatible network.

Is the StarTech USB3SDOCKHD Laptop Docking Station hot-swappable?

Yes, the StarTech USB3SDOCKHD Laptop Docking Station is hot-swappable, meaning you can connect or disconnect it from your laptop while it is powered on. This provides flexibility and convenience when you need to quickly switch between working with or without the docking station.

Can I use the StarTech USB3SDOCKHD Laptop Docking Station with multiple laptops?

The StarTech USB3SDOCKHD Laptop Docking Station is primarily designed to be used with a single laptop at a time. While you can physically connect it to multiple laptops, it is not designed for seamless switching between different laptops without disconnecting and reconnecting the docking station.

Does the StarTech USB3SDOCKHD Laptop Docking Station require any additional drivers or software to work?

The StarTech USB3SDOCKHD Laptop Docking Station is plug-and-play, meaning it should work without the need for any additional drivers or software installation. However, it is recommended to check the product documentation or the manufacturer's website for any specific driver or software requirements or updates.

What is included in the package when purchasing the StarTech USB3SDOCKHD Laptop Docking Station?

The contents of the package typically include the StarTech USB3SDOCKHD Laptop Docking Station, a USB 3.0 cable for connecting the docking station to your laptop, a power adapter, and an instruction manual. Be sure to check the product listing or package contents to confirm what is included.

Download This PDF Link:StarTech USB3SDOCKHD Laptop Docking Station User Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>