TURBO ENERGY 48V 2.4 kWh Hybrid Inverter Installation Guide
- October 30, 2023
- TURBO ENERGY
Table of Contents
TURBO ENERGY 48V 2.4 kWh Hybrid Inverter
Product Information
The product is a hybrid inverter from Turbo Energy that comes with a lithium battery series of 48V and 2.4 kWh capacity. The inverter is designed to optimize the use of renewable energy sources and provide uninterrupted power supply. The inverter can be connected to a wireless network for remote monitoring and control.
The product manufacturer’s website is https://www.turbo-e.com/.
TURBO ENERGY HYBRID INVERTER configuration
-
Step 1: Connect to Wi-Fi network
- Select the network named “AP_Serial number of the HI”.
- Enter the password displayed on the logger.
- Select the option to connect.
- If the network is not available, wait for a few minutes or reconnect the logger.
Notice: The settings listed below are for Windows and are for reference only. If other operating systems are used, please follow the corresponding procedures.
With an electronic device that has Wi-Fi (PC, Tablet, Smartphone…) the connection with the Wi-Fi of the hybrid inverter (HI) is established. To do this, open the wireless network connection, click on see the available wireless networks and select the one corresponding to the device with which you want to connect.
The name of the network to select is AP_ Serial
number of the HI. Enter the password that appears in the logger and select the
option to connect. The default password for hybrid inverters appears on their
label located on the bottom of the device (example photo).
Warning: If the
network to be selected is not available in the list of wireless networks,
there may be problems in the connection or in the configuration of the
recorder. Wait a few minutes to update the list or connect the logger again.
-
Step 2: Establish connection to the logger
- Access the internet from your browser (recommended browsers are Internet Explorer 8+, Google Chrome 15+ and Firefox 10+).
- Enter the following: 10.10.100.254.
- Enter the default username and password, which is “admin”.
- Once inside the Status page, click on Wizard to follow the quick setup wizard.
- Select the wireless network you need to connect to and click Next.
- If the signal strength (RSSI) of the selected network is low, consider moving the logger closer to the router or using a Wi-Fi extender.
Once connected to Wi-Fi, access the internet from your browser (recommended browsers: Internet Explorer 8+, Google Chrome 15+ and Firefox 10+) and enter the following: 10.10.100.254. Then, write the username and password, both are “admin” by default. Once inside the “Status” page, you can see the general information of the logger.
To continue, follow the quick setup wizard by
clicking on “Wizard”. Select the wireless network you need to connect to and
click “Next”.
Notice: If the signal strength (RSSI) of
the selected network is <15% with an unstable connection, adjust the router’s
antenna or use a repeater to improve the signal. The network SSID of the
selected router must be less than 30 characters with no blank spaces.
Enter the password of the selected network, select “Enable” to get an IP
address automatically, and click “Next”.
Warning: The router password cannot be recognized if it contains any characters such as &, #, % and blanks. If you have entered an invalid password or encryption method, an error message will appear. Improve the Wi-Fi security settings by selecting the options listed and clicking “Next”.
If the setting is successful, you will advance to the next page where you must
click “OK” to restart.
If the restart is successful, a message will appear indicating that it was
successful, if not, you must refresh the page.
Log back in to the “Status” page after restarting the web page and check the status of the recorder’s network connection.
Notice : After completing the network setup, the Wireless AP Mode should be enabled and the information regarding your router will be displayed on the interface automatically. Also, Remote Server A should be connected.
- Step 3: Inverter configuration
Once the connection is established, it is necessary to configure the working mode to be used and the type of batteries connected. To do this, from the inverter display itself, select the configuration option and click on System Work Mode. Within this tab, the parameters must be adjusted depending on the installation:
LITHIUM SERIES 48V 2.4 kWh BATTERIES configuration
The configuration of the DIPs must be the following:
WIRING configuration
The cable necessary to make the connection is the RJ45. It is a special cable
that is made up of 8 smaller cables each with a different color
configuration.
Following these steps will enable you to remotely monitor and control your hybrid inverter using a wireless network.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>