MarineLand ML90609-00 Portrait Aquarium Kit User Guide

: August 16, 2024
: MARINELAND

Table of Contents

MarineLand ML90609-00 Portrait Aquarium Kit
IMPORTANT SAFEGUARDS WARNING
Unpack the Aquarium
Parts Check
Filter Setup
Tank Setup
Maintenance
Replacement Parts List
How To use
Troubleshooting Guidelines
How To Diagrams
LIMITED WARRANTY
FREQUENTLY ASKED QUESTIONS
VIDEO – PRODUCT OVERVIEW
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MarineLand ML90609-00 Portrait Aquarium Kit

IMPORTANT SAFEGUARDS WARNING

To guard against injury, basic safety precautions should be observed, including the following:

READ AND FOLLOW ALL

SAFETY INSTRUCTIONS DANGER: To avoid possible electric shock, special care should be taken in the use of aquarium equipment. For each of the following situations, do not attempt repairs yourself. Return the appliance to an authorized service facility for service or discard the appliance.

If the appliance falls into the water, DON’T reach for it. First, unplug it and then retrieve it. If the electrical components of the appliance get wet, unplug it immediately.
If the appliance shows any sign of abnormal water leakage, immediately unplug it from the power source.
Carefully examine the appliance after installation. It should not be plugged in if there is water on parts not intended to be wet.
Do not operate any appliance if it has a damaged cord or plug, if it is malfunctioning, or if it is dropped or damaged in any manner.
To avoid the possibility of the appliance plug or receptacle getting wet, position the aquarium stand and tank to one side of a wall-mounted receptacle to prevent water from dripping onto the receptacle or plug. A “drip loop”, shown in the figure at right, should be arranged by the user for each cord connecting an aquarium appliance to a receptacle. The“drip loop” is that partof the cord below the level of the receptacle or the connector, if an extension cord is used, to prevent water from traveling along the cord and coming in contact with the receptacle. If the plug or receptacle does get wet, DON’T unplug the cord. Disconnect the fuse or circuit breaker that supplies power to the appliance. Then unplug and examine for the presence of water in the receptacle.
Close supervision is necessary when any appliance is used by or near children.
To avoid injury, do not contact moving parts or hot parts such as heaters, reflectors, lamp bulbs, etc.
Always unplug an appliance from an outlet when not in use, before putting on or taking off parts, and before cleaning. Never yank the cord to pull the plug from the outlet. Grasp the plug and pull to disconnect.
Do not use an appliance for other than intended use. The use of attachments not recommended or sold by the appliance manufacturer may cause an unsafe condition.
Do not install or store the appliance where it will be exposed to the weather or to temperatures below freezing.
Make sure an appliance mounted on a tank is securely installed before operating it.
Read and observe all the important notices on the appliance.
If an extension cord is necessary, a cord with a proper rating should be used. A cord rated for less amperes or watts than the appliance rating may overheat. Care should be taken to arrange the cord so that it will not be tripped over or pulled.
This appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Never use an extension cord unless the plug can be fully inserted. Do not attempt to defeat this safety feature.

SAVE THESE INSTRUCTIONS

Unpack the Aquarium

Remove the Glass Canopy from the top of the Styrofoam, then lift the Styrofoam out of the box.
Lift the glass Tank out of the box.
Remove the LED Light and cardboard tray from the bottom of the Tank.
Remove the Pump Power Cord from the Filter Box in the back of the Tank, but do not plug the Filter in until step 4G.
Remove the Filter Cartridge from the plastic bag and set the Cartridge aside.
Lift the Styrofoam from the bottom of the box to access the Tank Base.

Parts Check

Filter Setup

Set the Flow Adjustment Knob on the Filter Pump to the max setting. Once your Tank is running, refer to the “How To” section on the reverse side to adjust the flow if needed.
Make sure the Pump Tube is connected to the Filter Pump, Elbows, and Flow Nozzle.
Rinse the Filter Cartridge thoroughly and install it as shown (blue side toward the front of the aquarium).
Route the power cord over the back of the Tank, but do not plug the Filter Pump in until step 4F.

Tank Setup

First, clean the Tank by using clean water and paper towels. Do not use chemicals not intended for aquarium use.
Place the Base on a flat surface in your desired location away from direct sunlight and air vents, then place the Tank on top.
After rinsing your gravel and décor thoroughly, decorate your aquarium before adding water to avoid over-filling.
Locate the Min and Max Fill Lines on the Back Panel of the Tank. Fill the Tank with room temperature tap water treated with Marineland®Aquarium Conditioner to remove chlorine.
Add the LED Light to the back of the Tank as shown.
Place the Glass Canopy on the aquarium. When installed properly, the Glass Canopy slides back under the Filter Cover to provide easy access to the front of the Tank for feeding and maintenance.
Plug the Filter Pump and LED Light into the outlet.
If adding a heater (not included), do not place it in the filter box since the water level can drop causing the device to overheat. Place the heater inside the main tank as shown, and always follow the manufacturer’s directions for use.
Make drip loops for safety.

Maintenance

Replace the Filter Cartridge every two to four weeks.
Top off water to maintain water level between Min and Max Lines as needed (always treat water with Marineland® Aquarium Conditioner to remove chlorine).
Perform water changes monthly or as often as needed.
Use Marineland® pH Regulator weekly to maintain optimal aquarium chemistry.

Replacement Parts Diagram & Identification

Replacement Parts List

KEY	ITEM DESCRIPTION	MODEL
1	5g Pump, Tube	ML90625
2	Bio-Foam® Insert	ML90626
3	Nozzle & Elbows	ML90627
4	LED Light	ML90628
5	Sliding Glass Canopy	ML90632

How To use

Adjust the flow of the pump

To access the Filter Pump, first unplug it from the wall outlet. Remove the Filter Cover, grasp the Elbow that connects to the Flow Nozzle, and pull the Elbow off of the Flow Nozzle. This will allow you to pull the Pump out of the Filter Box.
Turn the Flow Adjustment Knob counterclockwise to decrease flow or clockwise to increase flow.

Access the impeller

To disassemble the Filter Pump, remove the Pump Cover, and then the Impeller Cover by gripping and pulling off. Remove the Impeller Assembly by pulling it out of the Main Pump Body (note: magnets hold the Impeller in place).
To assemble the pump, install the Impeller Assembly by inserting it into the Main Pump Body. Install Impeller Cover with tab pointed at 3:00 (see diagram). Install the Pump Cover by snapping it into the Main Pump Body.

Perform a water change

Once a month (or as often as needed depending on the bio-load), remove 50% of the water using a gravel cleaner. It’s usually easiest to remove décor before you begin. Add room temperature water treated with Marineland® Aquarium Conditioner to remove chlorine.

Feed your fish

Feed your fish two to three times daily, being careful not to overfeed. Only put as much food into the tank as your fish can consume in several minutes. To reduce the amount of food that is caught in the filter, you may want to unplug the filter before you begin feeding.

Change your cartridge

Every two to four weeks, remove the old Cartridge from the Cartridge Carrier. After removing the new Cartridge from the packaging, rinse it with clean water before sliding it into the Cartridge Carrier with the blue floss facing forward.
Note: some models of the Rite-Size Z Cartridge have a plastic tab on the side that should be snapped off to enable it to fit in the carrier.

Troubleshooting Guidelines

SYMPTOM	COMMENTS/SOLUTIONS
If your filter fails to pump water or flow has slowed…	• Lift the Cartridge

out of the Cartridge Carrier to see if water flow is restored. If so, your Cartridge is clogged and must be replaced. • Make sure the water level is between the Min/Max Fill Lines. • Make certain the Power Cord is functioning properly. Unplug the electrical cord momentarily, then reconnect it to the power source to restart the Impeller. • Make sure the adjustable Filter Pump is set to the desired flow. • Check the Impeller Assembly to ensure it is working properly.
If your filter makes excessive mechanical noise…| • The Filter Pump may be running dry. Make sure the water level is between the Min/Max Fill Lines engraved on the back wall of the tank. • Lift the Cartridge out of the Cartridge Carrier to see if water flow is restored. If so, your Cartridge is clogged and must be replaced. • Check the Impeller Assembly for debris.
If the water level in the filter box is low…| • Lift the Cartridge out of the Cartridge Carrier to see if water level is restored. If so, your Cartridge is clogged and must be replaced.
If there are excessive bubbles or scum on the surface of the water…| • Make sure the water level is between the Min/Max Fill Lines. This will ensure the surface of the water is skimmed.
If the water flow is too strong…| • Adjust the flow of the Filter Pump (see the “How To” section for instructions).
If water is flowing over the Back Panel…| • Change the Cartridge and ensure the water level is between the Min/Max Fill Lines labeled on the Back Panel.
If the LED Light seems dim…| • Wipe the cover of the LED Light and the Glass Canopy with a clean wet cloth, and make sure the DC Jack is properly attached to the Light Transformer.
If the canopy becomes difficult to slide…| • Wipe the Canopy Rails and Tank edges with a clean wet cloth.
If the BioFoam® Insert becomes discolored or dirty…| • This is not a problem. It indicates the growth of beneficial biological bacteria which remove toxic ammonia and nitrite from aquarium water. As long as the BioFoam is not damaged, it does not need to be replaced.

How To Diagrams

LIMITED WARRANTY

Within two years from the date of original purchase, United Pet Group, Inc. will repair or replace, at its option, any Portrait Kit that is deemed defective in workmanship or materials. Please return the unit, together with proof of date of purchase.
Call 800-322-1266 for return authorization and shipping address.
Damage or injuries resulting from negligence or misuse are not covered by this warranty.
Incidental or consequential damages are specifically excluded.* This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
Because some states do not allow the exclusion of incidental or consequential damages, this exclusion may not apply to you.

United Pet Group, Inc. Cincinnati, OH 45230

1.800.322.1266
www.marineland.com

Questions or Missing Parts: Call Customer Service at 800-322-1266

FREQUENTLY ASKED QUESTIONS

What are the dimensions of the MarineLand ML90609-00 Portrait Glass LED Aquarium Kit?

The MarineLand ML90609-00 Portrait Glass LED Aquarium Kit measures 9.5 inches in length, 9.5 inches in width, and 14 inches in height.

What is the weight of the MarineLand ML90609-00 Portrait Glass LED Aquarium Kit?

The MarineLand ML90609-00 Portrait Glass LED Aquarium Kit weighs 16 pounds.

What is the price of the MarineLand ML90609-00 Portrait Glass LED Aquarium Kit?

The MarineLand ML90609-00 Portrait Glass LED Aquarium Kit is priced at $77.99.

What brand manufactures the MarineLand ML90609-00 Portrait Glass LED Aquarium Kit?

The MarineLand ML90609-00 Portrait Glass LED Aquarium Kit is manufactured by Marineland.

What type of lighting does the MarineLand ML90609-00 Portrait Glass LED Aquarium Kit feature?

The MarineLand ML90609-00 Portrait Glass LED Aquarium Kit features LED lighting.

What should you consider when setting up the MarineLand ML90609-00 Portrait Glass LED Aquarium Kit?

Ensure the aquarium is placed on a stable surface and follow the setup instructions provided for installing the LED lighting and any additional equipment.

How should the MarineLand ML90609-00 Portrait Glass LED Aquarium Kit be maintained?

Regular maintenance includes cleaning the tank, changing the water as needed, and ensuring the LED lighting is functioning properly.

What are the benefits of the LED lighting in the MarineLand ML90609-00 Portrait Glass LED Aquarium Kit?

LED lighting enhances the visibility of fish and decorations, provides energy efficiency, and has a longer lifespan compared to traditional lighting.

How does the design of the MarineLand ML90609-00 Portrait Glass LED Aquarium Kit benefit fish viewing?

The portrait design allows for a vertical display, which can create a unique viewing experience and fit into smaller spaces.

How can you ensure the best performance of the MarineLand ML90609-00 Portrait Glass LED Aquarium Kit?

To ensure the best performance, follow the setup and maintenance instructions provided, use appropriate water treatments, and regularly check the functionality of the LED lighting and filtration system.

Why is the water in my MarineLand ML90609-00 Portrait Aquarium Kit cloudy?

Cloudy water can be caused by overfeeding, improper cycling, or inadequate filtration. Ensure you are not overfeeding, allow the tank to cycle properly, and clean or replace the filter media as needed.

What should I do if the LED lights on my MarineLand ML90609-00 Portrait Aquarium Kit are not working?

First, check the power connection and ensure the switch is turned on. If the problem persists, inspect the LED unit for any visible damage or loose connections. Consider replacing the LED light if it’s faulty.

Why is there algae growth in my MarineLand ML90609-00 Portrait Aquarium Kit?

Algae growth can result from excess lighting, overfeeding, or poor water quality. Reduce the lighting duration, feed the fish less, and perform regular water changes. Adding algae-eating fish or using an algae control product can also help.

How can I fix the filter in my MarineLand ML90609-00 Portrait Aquarium Kit if it's making loud noises?

Loud filter noises may be due to trapped air, debris in the impeller, or low water levels. Ensure the filter is fully submerged, clean the impeller and other filter parts, and check the water level in the tank.

Why are the fish in my MarineLand ML90609-00 Portrait Aquarium Kit swimming erratically?

Erratic swimming can indicate poor water quality, incorrect water temperature, or stress. Test the water for ammonia, nitrites, and pH levels, adjust the heater if needed, and make sure the tank environment is stable and free of stressors.