THE OUTDOOR GREATROOM BRON5151-K Bronson Block Square Gas Fire Pit Table Instruction Manual

THE OUTDOOR GREATROOM  BRON5151-K Bronson Block Square Gas Fire Pit Table

Bronson Fire Pit

Installation Instructions for Bronson Pit Table

Model: BRON5151-K
Website: outdoorrooms.com

IMPORTANT: Installation includes lighting and operating instructions, safety information, and proper tightening of connections with two wrenches.

Contents

1. About Your Fire Table
   • Required Tools
   • Included With Your Fire Pit:
2. Setting Up Your Burner
   • Assembly Instructions
   • Finishing Fire Pit
3. Operating Instructions
4. Warnings
5. Warranties

Product manual revision: 42527 REV C 01-20-22

About Your Fire Table

Required Tools

• Tools to cut and remove packaging
• Tools to secure gas connections
• Tools for assembly
• Tools required for electric spark igniter installation

Included With Fire Pit Kit

• 42 pieces of 11.75 x 7.875 x 4.00 Brick (BRON5151-K) (42)
• 6 pieces of 7.875 x 4.00 x 4.00 Brick (BRON5151-K) (6)
• BI28 Burner and Accessories (1)
• Tumbled Lava Rock (LAV-TMB) (13)
• 42 Inch Square Burner Plate (BP42S) (1)
• Control Panel (10259) (1)
• Control Panel Block (10366) (1)
• Vent Block (10367) (2)
• 34 Whistle Free Stainless Steel Flex Line (10367) (1)

Setting Up Your Burner
ATTENTION: DO NOT USE TEFLON TAPE OR PIPE DOPE ON FLARE FITTINGS.

Gas Connections
Follow the instructions below carefully when connecting the gas:

1. Turn off the gas supply valve.
2. Remove the burner plate and burner from the fire pit.
3. Remove the 24-inch flex line between burner orifice and valve and connect the included 34-inch flex line using two wrenches to tighten and perform a leak test.
4. Set the burner into the burner plate.
5. Position the burner plate in the center of the fire pit and then pull it so that the end is slightly off the edge. Leave a gap between the control panel block and burner plate so that hands are able to fit and make connections outlined in future steps.

Assembly Instructions

WARNING: Exposed edges may be rough, use leather gloves when removing packaging and handling the bricks.

Unpacking
Do not discard any packaging until assembly is complete and unit is tested. Keep all included manuals in a safe place for future reference. Keep bricks stacked until ready to be placed.

1-3 Brick Rows Assembly
Follow the instructions below carefully to assemble the first three rows of bricks:

1. Once the desired location for the fire pit has been determined, start with placing the first layer of bricks. Follow the diagram shown below for layout pattern.
2. Continue on to the second row of bricks. This layer will contain the two vent blocks (included in kit). Follow the diagram shown below for layout pattern.
3. Continue on to the third row of bricks. This layer will contain the control panel block (included in kit). Follow the diagram shown below for layout pattern.

Layer 1

AA
A
AA
Key A - 11.25 x 7.875 block 
    B - 4.00 x 7.875 block
A
A
B
B
A
A
AA
A
AA
FRONT

Layer 2

A
A BA
A
A
A
VENT BLOCK
VENT BLOCK
A
A
Key A - 11.25 x 7.875 block 
    B - 4.00 x 7.875 block
A
A BA
A
FRONT

Layer 3

AA
A
AA
A
A
B
B
A
A
Key A - 11.25 x 7.875 block 
    B - 4.00 x 7.875 block
AA
AA
CONTROL PANEL BLOCK FRONT

CF-SPARKER Assembly
Follow the instructions below carefully to assemble the CF-SPARKER:

1. Insert the CF-SPARKER into the hole in the control panel block.
2. Secure the CF-SPARKER to the control panel block with the screws provided.

Control Panel Assembly
Follow the instructions below carefully to assemble the control panel:

1. Insert the control panel into the control panel block.
2. Secure the control panel to the control panel block with the screws provided.

Thermocouple Installation
Follow the instructions below carefully to install the thermocouple:

1. Insert the thermocouple into the hole in the control panel, and then into the hole in the burner plate.
2. Secure the thermocouple to the burner plate with the set screw provided.

Electrode Installation
Follow the instructions below carefully to install the electrode:

1. Insert the electrode into the hole in the burner plate.
2. Secure the electrode to the burner plate with the lock nut provided.

Finishing Fire Pit
Follow the instructions below carefully to finish assembling your fire pit:

1. Attach the control panel to the control panel block using screws provided.
2. Complete the final brick layer assembly.
3. Install fire media.

Control Panel Attachment
Attach the control panel to the control panel block using screws provided.

Final Brick Layer Assembly
Complete the final brick layer assembly.

Fire Media Installation
Install fire media according to manufacturer instructions.

Operating Instructions
Follow the instructions below carefully to operate your fire pit:

1. Turn on the gas supply valve.
2. Press and hold the control knob in the pilot position.
3. Press the igniter button repeatedly until the pilot lights.
4. Release the control knob and wait for 30 seconds.
5. Turn the control knob to the on position to light the burner.

Warnings
Read all warnings and safety information included with your fire pit before use.

Warranties
Contact the manufacturer or visit their website for warranty information.

IMPORTANT
Please consult your Crystal Fire® Plus instruction manual for detailed instructions and important information related to the burner installation including: lighting and operating instructions, safety information, and proper tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE® PLUS BURNER WITHOUT CONSULTING THE CRYSTAL FIRE® PLUS OWNER’S MANUAL.

ABOUT YOUR FIRE TABLE

A. REQUIRED TOOLS

• Utility Knife
  To cut and remove packaging

• 2 Open Ended Wrenches
  To secure gas connections

• Phillips Screw Driver (Do not use a drill to assemble)
  For assembly

• One AAA Battery (Not Included)
  Required for electric spark igniter installation

INCLUDED WITH FIRE PIT KIT

Refer to Crystal Fire® Plus manual for items included with Crystal Fire® Plus burners

SETTING UP YOUR BURNER

ATTENTION
Read and understand your Crystal Fire® Plus owner’s manual before beginning burner hookups or using the device.
DO NOT USE TEFLON TAPE OR PIPE DOPE ON FLARE FITTINGS.

IMPORTANT
Please consult your Crystal Fire® Plus instruction manual for detailed instructions and important information related to the burner installation including: lighting and operating instructions, safety information, and proper tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE® PLUS BURNER WITHOUT FIRST CONSULTING THE CRYSTAL FIRE® PLUS OWNER’S MANUAL.

GAS CONNECTIONS

• See Crystal Fire® Plus instructions for burner installation.
• All gas connections were completed at the factory.
• Check all connections for leaks. If needed, tighten connection with 2 wrenches and re-check for leaks.
• For hard piped installations. Connect the gas supply line (not included) to the 3/8” male flare fitting on the valve.
  USE TWO WRENCHES TO ENSURE A GAS TIGHT CONNECTION.

PRODUCT ASSEMBLY INSTRUCTIONS

WARNING
Exposed edges may be rough, use leather gloves when removing packaging and handling the bricks.

UNPACKING
Do not discard any packaging until assembly is complete and unit is tested. Keep all included manuals in a safe place for future reference. Keep bricks stacked until ready to be placed.

1-3 BRICK ROWS ASSEMBLY

1.  Once desired location for fire pit has been determined, start with placing first layer of bricks. Follow the diagram shown below for layout pattern.
2. Continue on to second row of bricks. This layer will contain the 2 vent blocks (included in kit) and the control panel block (included in kit). Follow diagram shown below for layout pattern.
3. Continue on to third row of bricks. This layer will contain the control panel block (included in kit). Follow diagram shown below for layout pattern.
4. Unpack burner. Before installing the burner into the burner plate, remove the 24 inch flex line between burner oriface and valve and connect included 34 inch flex line. Use 2 wrenches to tighten and perform leak test. Set burner into burner plate.
   Position burner plate in center of fire pit and then pull plate so that end is slightly off edge. Leave a gap between control panel block and burner plate so that hands are able to fit and make connections outlined in future steps.

CF-SPARKER ASSEMBLY

• Locate CF-SPARKER inside of Crystal Fire® Plus burner box.
• Remove CF-SPARKER cap and hex nut. Insert AAA battery (not included) with + end out.
• Install CF-SPARKER into control panel as shown below. CF-SPARKER must be installed BEFORE control valve.
• Press in CF-SPARKER button to test your sparker.

CONTROL PANEL ASSEMBLY

• Pull the VCSV valve through the back and then front opening of the control panel block.
• Connect a whistle free flexible gas supply line to the inlet of valve using a ½” flare nut.
• Attach burner valve to control panel with provided screws.
  Ensure CF-SPARKER is installed before this step.

THERMOCOUPLE INSTALLATION

• Refer to Crystal Fire® Plus instruction manual for detailed attachment of thermocouple.
• Attach thermocouple to burner valve as shown below.

ELECTRODE INSTALLATION

• Connect igniter and ground wire to sparker box. Both wires can connect to either connection point. The unit will operate in either configuration.
• Test system by pushing the button on the igniter. Consult the troubleshooting section of the Crystal Fire® Plus owner’s manual if the spark is weak, intermittent or not present.

FINISHING FIRE PIT

CONTROL PANEL ATTACHMENT
Push control panel back into control panel block, making sure all connections are tucked in and not kinked. Using the 4X provided metal screws, attach the control panel to the control panel block. Finalize by pressing the control panel knob onto the stem of the VCSV valve.

FINAL BRICK LAYER ASSEMBLY
Move burner and burner plate back towards center of fire pit. Place bricks as final layer. Follow diagram shown below for layout pattern.

WARNING
DO NOT OPERATE CRYSTAL FIRE® PLUS BURNER WITHOUT INCLUDED GLASS BEADS OR OTHER APPROVED FIRE MEDIA.

OPERATING INSTRUCTIONS

IMPORTANT
Before operating your BRON5151-K, ensure all gas connections are properly tightened and thoroughly leak checked. Refer to the Crystal Fire® Plus manual for information on proper leak checking and other critical safety
information.

WARNING
FIRE OR EXPLOSION HAZARD
If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury, or loss of life.

Verify control valve is in OFF position. If operating on a self-contained propane cylinder, ensure cylinder valve is CLOSED. If operating on a hard- piped system, ensure main gas supply shut-off valve and all other valves in gas system are OPEN.

If operating on a self-contained propane cylinder, slowly open cylinder valve.

Press and hold sparker button. Verify an audible and visible spark is present within the ignition wind guard.

Gently press and turn control knob to LOW/IGNITION position. Fully depress control knob and hold for 3-5 seconds. Burner should ignite and continue to operate when control knob is released.

If burner does not light or remain lit after 20 seconds of attempting ignition, turn control valve to OFF position and wait 5 minutes to allow gas to dissipate before attempting ignition again. DO NOT ATTEMPT TO LIGHT BURNER IF YOU SMELL GAS.

With burner lit and operating, the flame height can be adjusted between LOW and HIGH at any time.

WARNINGS
IMPORTANT
Please consult your Crystal Fire® Plus instruction manual for detailed instructions and important information related to the burner installation including: lighting and operating instructions, safety information, and proper tightening of connections with two wrenches.

DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE® PLUS BURNER WITHOUT FIRST CONSULTING THE CRYSTAL FIRE® PLUS OWNER’S MANUAL.

WARNING
After consulting the manual and following instructions, remember: before operating, all gas connections must be fully checked for leaks.

WARNING: This product can expose you to chemicals including Carbon Monoxide and Benzene which are known to the State of California to cause cancer or birth defects or reproductive harm. For more information, visit www.P65Warnings.ca.gov

WARRANTIES

PRODUCT CATEGORY|

WARRANTY INFORMATION

---|---
GAS FIRE PIT TABLES/CRYSTAL FIRE® PLUS BURNER| Limited lifetime warranty on all stainless steel burners installed in a residential setting, and 5 years on all stainless steel burners installed in a commercial setting.

One year warranty on ignition & electronics

One year finish warranty

Three year structural warranty on all fire pit bases and tops

Thank you for purchasing an Outdoor GreatRoom Company product! This fire pit was made with pride in the USA.

Warranty: Fire pit tables are covered under a 1 year manufacturer’s warranty.
Please visit http://www.outdoorrooms.com/product-registration to register your product.

9583 217th St. W. • Lakeville, MN 55044
Toll Free: 1-866-303-4028 • Sales@OutdoorRooms.com

References

• Fire Pits, Fire Pit Tables, Propane Fire Pits, Outdoor Fire Pits, Outdoor Kitchens & Patio Furniture - The Outdoor GreatRoom Company
• Product Registration Form - The Outdoor GreatRoom Company

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>