THE OUTDOOR GREATROOM COMPANY BRON5151-K Bronson Fire Pit Instruction Manual

Bronson Fire Pit
Installation Instructions for Bronson Pit Table
BRON5151-K

IMPORTANT
Please consult your Crystal Fire® Plus instruction manual for detailed instructions and important information related to the burner installation including lighting and operating instructions, safety information, and proper tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL THE CRYSTAL FIRE® PLUS BURNER WITHOUT CONSULTING THE CRYSTAL FIRE® PLUS OWNER’S MANUAL.

ABOUT YOUR FIRE TABLE

A. REQUIRED TOOLS

• Utility Knife
  To cut and remove packaging

• 2 Open Ended Wrenches
  To secure gas connections

• Phillips Screw Driver (Do not use a drill to assemble)
  For assembly

• One AAA Battery (Not Included)
  Required for electric spark igniter installation

B. INCLUDED WITH FIRE PIT KIT

Refer to the Crystal Fire® Plus manual for items included with Crystal Fire® Plus burners

SETTING UP YOUR BURNER

ATTENTION
Read and understand your Crystal Fire® Plus owner’s manual before beginning burner hookups or using the device.
DO NOT USE TEFLON TAPE OR PIPE DOPE ON FLARE FITTINGS.
IMPORTANT
Please consult your Crystal Fire® Plus instruction manual for detailed instructions and important information related to the burner installation including lighting and operating instructions, safety information, and proper tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL THE CRYSTAL FIRE® PLUS BURNER WITHOUT FIRST CONSULTING THE CRYSTAL FIRE® PLUS OWNER’S MANUAL.
A. GAS CONNECTIONS

• See Crystal Fire® Plus instructions for burner installation.
• All gas connections were completed at the factory.
• Check all connections for leaks. If needed, tighten the connection with 2 wrenches and re-check for leaks.
• For hard-piped installations. Connect the gas supply line (not included) to the 3/8” male flare fitting on the valve. USE TWO WRENCHES TO ENSURE A GAS-TIGHT CONNECTION.

ASSEMBLY INSTRUCTIONS

WARNING
Exposed edges may be rough, use leather gloves when removing packaging and handling the bricks.
A. UNPACKING
Do not discard any packaging until assembly is complete and the unit is tested. Keep all included manuals in a safe place for future reference. Keep bricks stacked until ready to be placed.
B. 1-3 BRICK ROWS ASSEMBLY

1. Once the desired location for the fire pit has been determined, start with placing the first layer of bricks. Follow the diagram shown below for the layout pattern.
   

2. Continue on to the second row of bricks. This layer will contain the 2 vent blocks (included in the kit). Follow the diagram shown below for the layout pattern.
   

3. Continue on to the third row of bricks. This layer will contain the control panel block (included in the kit). Follow the diagram shown below for the layout pattern.
   

4. Unpack the burner. Before installing the burner into the burner plate, remove the 24-inch flex line between the burner orifice and valve and connect included 34-inch flex line. Use 2 wrenches to tighten and perform a leak test. Set burner into burner plate.
   Position the burner plate in the center of the fire pit and then pull the plate so that end is slightly off edge. Leave a gap between the control panel block and burner plate so that hands are able to fit and make connections outlined in future steps.
   

C. CF-SPARKER ASSEMBLY

• Locate CF-SPARKER inside of Crystal Fire® Plus burner box.
• Remove the CF-SPARKER cap and hex nut. Insert AAA battery (not included) with + end out.
• Install CF-SPARKER into the control panel as shown below. CF-SPARKER must be installed BEFORE the control valve.
• Press in CF-SPARKER button to test your sparker.
  

D. CONTROL PANEL ASSEMBLY

• Pull the VCSV valve through the back and then front opening of the control panel block.
• Connect a whistle-free flexible gas supply line to the inlet of the valve using a ½” flare nut.
• Attach burner valve to control panel with provided screws. Ensure CF-SPARKER is installed before this step.
  

E. THERMOCOUPLE INSTALLATION

• Refer to the Crystal Fire® Plus instruction manual for a detailed attachment of the thermocouple.
• Attach thermocouple to burner valve as shown below.
  

F. ELECTRODE INSTALLATION

• Connect igniter and ground wire to sparker box. Both wires can connect to either connection point. The unit will operate in either configuration.
• Test system by pushing the button on the igniter. Consult the troubleshooting section of the Crystal Fire® Plus owner’s manual if the spark is weak, intermittent, or not present.

FINISHING FIRE PIT

A. CONTROL PANEL ATTACHMENT
Push the control panel back into the control panel block, making sure all connections are tucked in and not kinked. Using the 4X provided metal screws, attach the control panel to the control panel block. Finalize by pressing the control panel knob onto the stem of the VCSV valve.
B. FINAL BRICK ROW ASSEMBLY
Move the burner and burner plate back towards the center of the fire pit. Place the final layer of bricks. Follow the diagram shown below for the layout pattern.

C. FIRE MEDIA INSTALLATION

• Scatter all included glass beads, lava rock, or other approved fire media evenly across the entire burner surface.

WARNING
DO NOT OPERATE THE CRYSTAL FIRE® PLUS BURNER WITHOUT INCLUDED GLASS BEADS OR OTHER APPROVED FIRE MEDIA.

OPERATING INSTRUCTIONS

IMPORTANT
Before operating your BRON5151, ensure all gas connections are properly tightened and thoroughly leak-checked. Refer to the Crystal Fire® Plus manual for information on proper leak checking and other critical safety information.
WARNING
FIRE OR EXPLOSION HAZARD
If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury, or loss of life.
Verify control valve is in the OFF position. If operating on a self-contained propane cylinder, ensure the cylinder valve is CLOSED. If operating on a hard- piped system, ensure the main gas supply shut-off valve and all other valves in the gas system areOPEN.
If operating on a self-contained propane cylinder, slowly open the cylinder valve.
Press and hold the sparker button. Verify an audible and visible spark is present within the ignition wind guard.
Gently press and turn the control knob to the LOW/IGNITION position. Fully depress the control knob and hold for 3-5 seconds. The burner should ignite and continue to operate when the control knob is released.
If the burner does not light or remain lit after 20 seconds of attempting ignition, turn the control valve to the OFF position and wait 5 minutes to allow gas to dissipate before attempting ignition again. DO NOT ATTEMPT TO LIGHT THE BURNER IF YOU SMELL GAS.
With the burner lit and operating, the flame height can be adjusted between LOW and HIGH at any time.

WARNINGS

IMPORTANT
Please consult your Crystal Fire® Plus instruction manual for detailed instructions and important information related to the burner installation including lighting and operating instructions, safety information, and proper tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL THE CRYSTAL FIRE® PLUS BURNER WITHOUT FIRST CONSULTING THE CRYSTAL FIRE® PLUS OWNER’S MANUAL.
WARNING
After consulting the manual and following instructions, remember: that before operating, all gas connections must be fully checked for leaks.
WARNING: This product can expose you to chemicals including Carbon Monoxide and Benzene which are known to the State of California to cause cancer or birth defects or reproductive harm. For more information, visit www.P65Warnings.cargo

WARRANTIES

all stainless steel burners installed in a residential setting, and 5 years on all stainless steel burners installed in a commercial setting.
One-year warranty on ignition & electronics One-year finish warranty Three year structural warranty on all fire pit bases and tops

Thank you for purchasing an Outdoor GreatRoom Company product! This fire pit was made with pride in the USA.

Warranty: Fire pit tables are covered under a 1-year manufacturer’s warranty.
Please visit http://www.outdoorrooms.com/product-registration
to register your product.

9583 217th
St. W. • Lakeville, MN 55044
Toll-Free: 1-866-303-4028
• Sales@OutdoorRooms.com

References

• Fire Pits, Fire Pit Tables, Propane Fire Pits, Outdoor Fire Pits, Outdoor Kitchens & Patio Furniture - The Outdoor GreatRoom Company
• outdoorrooms.com/product-registration

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>