ikan PT4700 17 Inch Teleprompter Pedestal and Dolly Turnkey User Guide

ikan PT4700 17 Inch Teleprompter Pedestal and Dolly Turnkey

Product Information

The PT4700-PEDESTAL is a turnkey broadcast solution offered by Ikan. This solution includes a 17-inch teleprompter, pedestal, and dolly. The system has been tested internally for payload compatibility. The 17 Professional High Bright Beam Splitter Teleprompter (PT4700) is equipped with a teleprompter glass frame, teleprompter hood, metal frame, washers, teleprompter boot, monitor mounts, and a teleprompter bracket. The teleprompter system is designed to accommodate camera setups up to 36.5 lbs after mounting the full 17 teleprompter without the counterweight. The pedestal can accommodate cameras up to 56.8 lbs. The package includes a hard case for the entire teleprompter system, a separate hard case for the pedestal, and a carrying bag for the dolly.

Product Usage Instructions

1. Place the teleprompter glass frame on a flat surface and remove the four screws.
2. Align and attach the teleprompter hood with the eight screw pegs from the teleprompter frame.
3. Ensure that the thicker side of the metal frame is on top and the slimmer side is on the bottom.
4. Put the washers on before tightening the screws. The washers and four additional screws are inside a bag on the bottom foam.
5. Extend the teleprompter hood open and attach the teleprompter boot using the clips. Align the seam with the bottom of the teleprompter hood.
6. Remove the monitor mounts from the teleprompter base using the included larger 4mm hex key to loosen from the 15mm rods.
7. Attach the monitor mounts on the back of the monitor’s VESA-compatible threads using the four included screws and provided a 2mm hex key.
8. Adjust the 15mm rods to accommodate the monitor, leaving about 1 inch of room for the teleprompter bracket. Make sure the 15mm rods go through both sets of monitor mounts. Ensure all screws are properly tightened after inserting the monitor.
9. While sliding the teleprompter bracket into the slot of the teleprompter base, pull on the red knob to allow the bracket to fully slide in.
10. Once the bracket is in place, tighten the side screw to lock it in place. Double-check and ensure all screws are tightened with the included hex keys.
11. (Optional) If the teleprompter is too front-heavy, attach the included counterweight to the back of the teleprompter base.

To make the teleprompter more portable, it is packed in a reusable, high- quality foam case designed to fit into Ikan’s PT-CASE-V2. Do not throw away the foam case. The monitor ports on the teleprompter include HDMI. For more information, visit www.ikancorp.com or contact Ikan at 1.713.272.8822 or sales@ikancorp.com.

OVERVIEW

• Ikan’s Turnkey Broadcast Solutions include everything you need for your professional camera setup. This solution includes a 17” teleprompter, pedestal, and dolly. All of our systems have been tested internally for payload compatibility.
• The remaining payload capacity, after mounting the full 17” teleprompter without the counterweight, can accommodate camera setups up to 36.5 lbs.
• The pedestal, without the teleprompter system, can accommodate cameras up to 56.8 lbs.
• This solution includes a hard case that features custom-cut foam for the entire teleprompter system. This bundle also includes a separate hard case for the pedestal, and a carrying bag for the dolly.

What’s Included

• 1 x Teleprompter Base
• 1 x Bracket with Glass
• 1 x Teleprompter Hood with Boot
• 1 x Monitor
• 1 x AC Adapters with Cord
• 1 x PrompterPro Software
• 1 x Counterweight Set (2 x 2.5 lbs)
• 2 x D-Ring ¼-20” Screws
• 2 x Hex Keys
• 3 x Height Risers

PT4700
17” Professional High Bright Beam Splitter Teleprompter

Teleprompter Assmebly Setup

• Step 1
  Place the teleprompter glass frame on a flat surface and remove the four screws as shown.

• Step 2
  Align and attach the teleprompter hood with the 8 screw pegs from the teleprompter frame.

• Step 3
  The metal frame is directional. Make sure the thicker side is on top and the slimmer side is on the bottom.

• Step 4
  Put the washers on before tightening the screws. The washers and 4 additional screws are inside a bag on the bottom foam.

• Step 5
  Extend the teleprompter hood open and attach teleprompter boot using the clips. It is suggested to align the seam with the bottom of the teleprompter hood.

• Step 6
  Remove the monitor mounts from the teleprompter base using the included larger 4mm hex key to loosen from the 15mm rods.

• Step 7
  Attach the monitor mounts on the back of the monitor’s VESA compatible threads using the 4 included screws and provided 2mm hex key.

• Step 8
  After the monitor mounts are attached, adjust the 15mm rods to accommodate the monitor. Leave about 1 inch of room for the teleprompter bracket. Make sure the 15mm rods go through both set of monitor mounts. Please ensure that all screws are properly tightened after inserting the monitor.

  • SAFETY NOTE Make sure to leave at least 2 inches of the rods inside the teleprompter base.

• Step 9
  While sliding the teleprompter bracket into the slot of the teleprompter base pull on the red knob to allow the bracket to fully slide in.

• Step 10
  Once the bracket is in place, tighten the side screw to lock in place. Double check and make sure all the screws are tightened with the included hex keys.

• Step 11 (optional)
  Should the teleprompter be too front heavy, you can attach the included counter weight on the back of the teleprompter base.

Foam Case
To make your teleprompter more portable, we packed it in a reusable, high- quality foam. The shape and size of the foam was designed to fit into Ikan’s PT-CASE-V2.

Monitor Ports

• BNC – AV Composite Input
• VGA – Video Graphics Array DE15 Connection
• HDMI – High-Definition Multimedia Interface Input Connection
• Power Port – 12-24v Input
• HDMI – Switch HDMI input
• VGA – Switch to VGA input
• AV – Switch to composite BNC input
• Flip – Toggle image fli p(Can be set to horizontal, vertical, or both via menu)
• Up Arrow – Toggle up to adjust setting
• Menu – Access to monitor settings
• Down Arrow – Toggle down to adjust setting

Monitor Menu Settings

• Video Config
  • Contrast (White Level)
  • Brightness (Black Level)
  • Tint (Chroma Hue)
  • Chroma (Chroma Saturation)
  • Sharpness (Detail)
  • RGB Setup – Manually configure RGB
  • Return
• System Config
  • Menu Duration – Set duration of how long menu stays on screen
  • Video Ratio – Set screen aspect ratio 16:9 or 4:3 (4:3 is
  • native resolution, 16:9 will create black bars)
  • Flip-H – Assign toggle button to flip image horizontally
  • Flip-V – Assign toggle button to flip image vertically
  • Reset – Factory reset
• Return
  • PC Setup (Only available for VGA)
  • H-Position – Adjust horizontal position
  • V-Position – Adjust vertical position
  • Auto – Monitor automatically adjust position
  • Return
• Exit

How to set-up FLIP button feature:

1. Press MENU button
2. Navigate to SYSTEM CONFIG.
3. Navigate to FLIP-V or FLIP-H
4. Change FLIP-V and/or FLIP-H to “ON”
5. Exit MENU
6. The FLIP button should now be activated and can be pressed to mirror the image Horizontally or Vertically
7. When FLIP-H is ON, the image will flip Horizontally
8. When FLIP-V is ON, the image will flip Vertically
9. If both are ON, the FLIP button will toggle both Horizontal and Vertical flip

Watch our VIDEO TUTORIAL on how to assemble Ikan Professional Teleprompters:https://youtu.be/5TjIxzBc_Vc.

Specifications

PT4700

Optional Accessories

• Replacement Glass for both PT4500 / PT4700
• PT15-HB-V2 15” High Bright Monitor (for PT4500)
• PT17-HB-V2 17” High Bright Monitor (for PT4700)
• PT-CASE-V2 Rolling Hard Case for PT4500/PT4700 Teleprompter

Learn More

• More dynamic information at the official website: www.ikancorp.com.

Support

• Contact email: support@ikancorp.com.

CONDITIONS OF WARRANTY SERVICE

• Free service for one year from the day of purchase if the problem is caused by manufacturing errors.
• The components and maintenance service fee will be charged if the warranty period has expired.

Free Service will not be Provided in the Following Situations: (*Even if the product is still within the warranty period.)

• Damage caused by abuse or misuse, dismantling, or changes to the product not made by the company.
• Damage caused by natural disasters, abnormal voltage, environmental factors, etc.

EP880SK

Component:

GH25 100mm Fluid Head

FEATURES

SPECIFICATIONS

EP880S

Component:

EI-7007 Super dolly

Designed for pedestal systems and another heavy-duty system. The 125mm/5inch wheels with cable guard can be individually braked, also the movement direction can be fixed. Folds for transporting.

FEATURES

GB3 Pan bar

Telescopic pan bar for GH08L, GH10L, GH15, GH25 heads

SPECIFICATIONS

• Length range 405-605mm / 15.9-23.8in
• Net weight 385g / 0.8lbs
• www.eimagevideo.com.
• www.ikancorp.com.
• 1.713.272.8822
• sales@ikancorp.com.

References

• Professional Video Production Equipment for Sale | Ikan

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>