THE OUTDOOR GREATROOM COMPANY BRK-1224-19 Brooks and Kenwood Fire Pit Table Instruction Manual
- June 9, 2024
- THE OUTDOOR GREATROOM COMPANY
Table of Contents
THE OUTDOOR GREATROOM COMPANY BRK-1224-19 Brooks and Kenwood Fire Pit
Table
IMPORTANT
Please consult your Crystal Fire instruction manual for detailed instructions
and important information related to the burner installation including:
lighting and operating instructions, safety information, and proper tightening
of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE BURNER WITHOUT FIRST CONSULTING THE
CRYSTAL FIRE OWNER’S MANUAL.
Required Tools
Utility Knife
To cut and remove packaging
2 Open Ended Wrenches
To secure gas connections
Leather Gloves
To protect hands from glass and sharp edges during install
One AAA Battery (not included)
Required for electric spark igniter installation
Phillips Screwdriver
To attach mounting screws to control panel
Two people are required for this installation
Included with your Fire Pit
Assembly Instructions
INSTALL NOTE: Final tightening of bolts should be completed following installation of all panels.
-
Unpack all the contents from the box and remove the individual packaging from each component.
-
Carefully lay the Top, with underside facing upwards, on a soft and flat surface.
-
Attach Panel A using Bolt A (X2) as shown below.
-
Attach Panel B on the opposite side of Panel A using Bolt A (X2) as shown below.
-
Attach Panel C using Bolt A (X4) as shown below.
NOTE: Drainage holes on Panel C must be facing down towards the surface on which you will be placing your fire pit. -
Attach Center Support piece, as shown below, to the bottom of the fire pit using Bolt A (X4).
NOTE: Drainage holes on Center Support piece must be facing down towards the surface on which you will be placing your fire pit. -
Do a final tightening of the bolts you have installed in your fire pit. Then, with the help of another person, turn the table right side up.
CF-SPARKER Installation
- Locate CF-SPARKER inside of Crystal Fire® Plus burner box.
- Remove CF-SPARKER cap and hex nut. Insert AAA battery (not included) with + end out.
- Install CF-SPARKER into control panel as shown below.
- Depress CF-SPARKER button to test your sparker.
Gas Connections
Read and understand your Crystal Fire® Plus owner’s manual before beginning burner hookups or using the device. Do not use Teflon tape or pipe dope on flare fittings.
- See Crystal Fire® Plus instructions for burner installation.
- All gas connections were completed at the factory.
- Check all connections for leaks. If needed, tighten connection with 2 wrenches and re-check for leaks.
- Attach burner valve to control panel with provided screws as shown below. Ensure sparker box is installed before this step.
Installation
Thermocouple Installation
- Refer to Crystal Fire® Plus instruction manual for detailed attachment of thermocouple.
- Attach thermocouple to burner valve as shown below.
Electrode Installation
- Connect igniter and ground wire to sparker box. Both wires can connect to either connection point. The unit will operate in either configuration.
- Test system by pushing the button on the igniter. Consult the troubleshooting section of the Crystal Fire® Plus Burner Owner’s Manual, if the spark is weak, intermittent, or not present.
Fire Media Installation
- Scatter all included glass beads, lava rock, or other approved fire media evenly across entire burner surface.
- DO NOT OPERATE CRYSTAL FIRE® PLUS BURNER WITHOUT INCLUDED GLASS BEADS OR OTHER APPROVED FIRE MEDIA
- DO NOT OPERATE CRYSTAL FIRE® BURNER WITH BURNER COVER IN PLACE
After installing CF-SPARKER and making gas connections, verify that all connections are tight and that no leaks are present using a solution of soapy water or a commercially available leak-check solution.
Position Your Tank (if applicable)
- Connect the propane hose/regulator to the propane tank and hand tighten (DO NOT USE A WRENCH) and slide the propane tank past the dotted line to ensure the Access Door closes properly. Attach the Access Door.
- With the tank inside, ensure that no hoses, wires, or any other components are kinked or touching the burner pan.
Riser Kit Installation
HAND-TIGHTEN ONLY. DO NOT USE TOOLS TO TIGHTEN THE RISER KIT HARDWARE.
- Assemble base according to Manual included with table
- Screw (4) spacers into threads on the underside of the table surface
- Place base, upside-down, onto spacers
- Secure base to spacers using 4 screws (included with table packaging). Do not overtighten.
IMPORTANT
Please consult your Crystal Fire® Plus instruction manual for detailed
instructions and important information related to the burner installation
including: lighting and operating instructions, safety information, and proper
tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE® PLUS BURNER WITHOUT FIRST CONSULTING
THE CRYSTAL FIRE® PLUS
Please consult your Crystal Fire® Plus instruction manual for detailed
instructions and important information related to the burner installation
including: lighting and operating instructions, safety information, and proper
tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE® PLUS BURNER WITHOUT FIRST CONSULTING
THE CRYSTAL FIRE® PLUS OWNER’S MANUAL.
WARNING
After consulting the manual and following instructions, remember; before
operating, all gas connections must be fully checked for leaks
Warranty
Warranty: Fire pit tables are covered under a 1- year manufacturer’s warranty. Please visit https://www.outdoorrooms.com/product-registration to register your product.
Care and maintenance note:
Light scratches may be removed from the poly-wood surfaces of this fire pit by
gently sanding with 220-grit sandpaper in the same direction as the grain.
Sanding too deeply or not following the grain of the material could result in
permanent damage.
9583 217th St. W. • Lakeville, MN 55044
Toll Free: 1-866-303-4028
Sales@OutdoorRooms.com
WARNING: This product can expose you to chemicals including Carbon Monoxide and Benzene which are known to the State of California to cause cancer or birth defects or reproductive harm. For more information, visit www.P65Warnings.ca.gov
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>