THE OUTDOOR GREATROOM COMPANY CV-30E Cove Edge Round Gas Fire Pit Instruction Manual
- June 4, 2024
- THE OUTDOOR GREATROOM COMPANY
Table of Contents
THE OUTDOOR GREATROOM COMPANY CV-30E Cove Edge Round Gas Fire Pit
IMPORTANT
Please consult your Crystal Fire instruction manual for detailed instructions
and important information related to the burner installation including:
lighting and operating instructions, safety information, and proper tightening
of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE BURNER WITHOUT FIRST CONSULTING THE CRYSTAL FIRE OWNER’S MANUAL.
Required Tools
- Two people are required for this installation.
- 2 Open Ended Wrenches
- To secure gas connections.
- Leather Gloves
- To protect hands from rough edges found on fire pit during installation.
- One AAA Battery (not included)
- Required for electric spark igniter installation.
- Utility Knife
- To cut and remove packaging.
- Power Drill
- To remove support board from crate.
Included with your Fire Pit
Assembly Instructions
- First, unscrew the shipping block with a power drill. Discard board. It will not be needed for further assembly of this product
- Remove fire pit base from the crate you received it in. Place the base in your desired location. Two people are recommended for this step of the installation.
CF-SPARKER Installation
- Locate CF-SPARKER inside of crystal fire burner box.
- Remove CF-SPARKER cap and hex nut. Insert AAA battery (not included) with + end out.
- Install CF-SPARKER into control panel as shown below.
- Depress CF-SPARKER button to test your sparker.
Gas Connections
Read and understand your Crystal Fire® Plus Burner Owner’s manual before beginning burner hookups or using the device. Do not use Teflon tape or pipe dope on flare fittings.
See Crystal Fire® Plus instructions for burner installation.
- All gas connections were completed at the factory.
- Check all connections for leaks. If needed, tighten connection with 2 wrenches and re-check for leaks.
- Attach burner valve to control panel with provided screws as shown below. Ensure sparker box is installed before this step.
Installation
Thermocouple Installation
- Refer to Crystal Fire® Plus instruction manual for detailed attachment of thermocouple.
- Attach thermocouple to burner valve as shown below.
Electrode Installation
- Connect igniter and ground wire to sparker box. Both wires can connect to either connection point. The unit will operate in either configuration.
- Test system by pushing the button on the igniter. Consult the troubleshooting section of the Crystal Fire® Plus Burner Owner’s Manual, if the spark is weak, intermittent, or not present.
Glass Installation
- Scatter all the included glass beads evenly onto burner surface.
- DO NOT OPERATE CRYSTAL FIRE® PLUS BURNER WITHOUT INCLUDED GLASS BEADS OR OTHER APPROVED FIRE MEDIA
- DO NOT OPERATE CRYSTAL FIRE® PLUS BURNER WITH BURNER COVER IN PLACE
CV-30-E Installation
- Place burner plate into Cove base.
- Remove the 4 ¼-20 stainless steel screws installed in revenues.
- Make gas connections.
- Ignition wind guard should be oriented towards cutout in burner plate. As shown in detailed view.
- Replace the 4 ¼-20 stainless steel screws back through the burner and tighten into rivnuts.
IMPORTANT
Please consult your Crystal Fire® Plus instruction manual for detailed
instructions and important information related to the burner installation
including: lighting and operating instructions, safety information, and proper
tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE® PLUS BURNER WITHOUT FIRST CONSULTING THE CRYSTAL FIRE® PLUS BURNER OWNER’S MANUAL.
WARNING
- After consulting the manual and following instructions, remember; before operating, all gas connections must be fully checked for leaks
- This product can expose you to chemicals including Carbon Monoxide and Benzene which are known to the State of California to cause cancer or birth defects or reproductive harm.
- For more information, visit www.P65Warnings.ca.gov
Warranty
Warranty
- Fire pit tables are covered under a 1- year manufacturer’s warranty. Please visit https://www.outdoorrooms.com/product-registration to register your product.
- Thank you for purchasing an Outdoor GreatRoom Company product! This fire pit was made with pride in the USA.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>