THE OUTDOOR GREATROOM COMPANY KN-1224 Kinney Fire Table Instruction Manual
- June 5, 2024
- THE OUTDOOR GREATROOM COMPANY
Table of Contents
Kinney Fire Table
Installation Instructions for Kinney Fire Pit Table
KN-1224
IMPORTANT
Please consult your Crystal Fire® Plus instruction manual for detailed instructions and important information related to the burner installation including lighting and operating instructions, safety information, and proper tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE® PLUS BURNER WITHOUT CONSULTING THE
CRYSTAL FIRE® PLUS
OWNER’S MANUAL.
ABOUT YOUR FIRE TABLE
A. REQUIRED TOOLS
-
Utility Knife
To cut and remove packaging -
2 Open-Ended Wrenches
To secure gas connections -
Phillips Screw Driver (Do not use a drill to assemble)
For assembly -
One AAA Battery (Not Included)-
Required for electric spark igniter installation
B. INCLUDED WITH YOUR FIRE PIT
IMPORTANT
The standard LP tank will not fit under the table. A special horizontal LP
tank can be purchased to fit.
A STANDARD TANK CAN BE USED AND MUST BE KEPT OUTSIDE OF THE TABLE.
DO NOT TIP STANDARD 20 LBS. TANK ON SIDE.
ASSEMBLY INSTRUCTIONS
IMPORTANT
Exposed edges may be sharp, use leather gloves
when removing packaging and handling the base.
A. UNPACKING
- Do not discard any packaging until assembly is complete and the unit is tested.
- Keep all included manuals in a safe place for future reference.
- Two people are recommended to remove the table from the packaging.
- Place the tablet in the desired location before installing the control valve and gas connection.
B. CF-SPARKER INSTALLATION
- Remove CF-SPARKER cap and hex nut. Insert AAA battery (not included) with + end out.
- Unscrew mounting screws from the control valve. Install CF-SPARKER on to control panel as shown below. Reconnect mounting screws and control valve to control panel.
- Press in CF-SPARKER button to test your spark.
SETTING UP YOUR BURNER
ATTENTION
Read and understand your Crystal Fire® Plus owner’s manual before
beginning burner hookups or using the device.
DO NOT USE TEFLON TAPE OR PIPE DOPE ON FLARE FITTINGS.
A. GAS CONNECTIONS
-
See Crystal Fire® Plus instructions for burner installation.
-
All gas connections were completed at the factory.
-
Check all connections for leaks. If needed, tighten the connection with 2 wrenches and re-check for leaks.
-
Attach included control valve knob to control valve stem.
-
For hard piped installations. Connect the gas supply line (not included) to the 3/8” male flare fitting on the valve. USE TWO WRENCHES TO ENSURE A GAS
TIGHT CONNECTION. -
Run gas pipe up through the opening between the 2 base plates as shown in the image below.
B. ELECTRODE INSTALLATION
- Connect igniter and ground wire to sparker box. Both wires can connect to either connection point. The unit will operate in either configuration.
- Test the system by pushing the button on the igniter. Consult the troubleshooting section of the Crystal Fire® Plus owner’s manual if the spark is weak, intermittent or not
present.
C. PROPANE TANK INSTALLATION
- Remove door on front side of table
- Pull out tank drawer.
- With the propane tank valve and fire pit valve off, attach the propane regulator to the propane tank.
- Place tank in tank tray.
- Slide tank drawer in. Ensure no hoses or wires are contacting the bottom of the burner.
- Replace the access door.
ATTENTION
HAND TIGHTEN, DO NOT USE A
WRENCH FOR THIS CONNECTION.
ATTENTION
Over time the bearings in the door glides may require re-greasing. Any spray
lubricant, such as WD-40, may be used to lubricate drawer glides.
Perform annually or on an as-needed basis to maintain smooth operation.
ATTENTION
STANDARD LP TANK WILL NOT FIT IN BASE. STANDARD LP TANK MUST SIT OUTSIDE OF
BASE.
DO NOT TIP THE STANDARD LP TANK ON ITS SIDE
Tanks under 14 inches can be used within the table but must be kept upright and not on their side.
MISCELLANEOUS
A. FIRE MEDIA INSTALLATION
- Scatter all included glass beads, lava rock, or other approved fire media evenly across the entire burner surface.
WARNING
DO NOT OPERATE CRYSTAL FIRE®
PLUS BURNER WITHOUT INCLUDED GLASS BEADS OR OTHER APPROVED FIRE MEDIA.
B. BURNER COVER INSTALLATION
- Fully shut off the gas supply to the table and turn the control valve knob to the OFF position. Wait for the burner to become cool before placing the cover.
- Carefully place the cover on top of the burner.
- Remove burner cover before attempting ignition.
WARNING
DO NOT OPERATE CRYSTAL FIRE®
PLUS BURNER WITH BURNER
COVER IN PLACE.
C. BURNER COVER STORAGE
When not in use, the Burner cover can be conveniently stored within the table.
- Remove the door on the back end of the table.
- Lay burner cover flat and slide in between the two guides. Push cover in enough so that door will not interfere with it once replaced.
- Replace door.
OPERATING INSTRUCTIONS
IMPORTANT
Before operating your KN-1224, ensure all gas connections are properly
tightened and thoroughly leak checked.
Refer to the Crystal Fire® Plus manual for information on proper leak checking
and other critical safety information.
WARNING
FIRE OR EXPLOSION HAZARD
If you do not follow these instructions exactly, a fire or explosion may
result causing property damage, personal injury, or loss of life.
Verify control valve is in the OFF position. If operating on a self-contained propane cylinder, ensure the cylinder valve is CLOSED. If operating on a hard- piped system, ensure the main gas supply shut-off valve and all other valves in the gas system are OPEN.
If operating on a self-contained propane cylinder, slowly open the cylinder
valve.
Press and hold the sparker button. Verify an audible and visible spark is
present within the ignition wind guard.
Gently press and turn the control knob to the LOW/IGNITION position. Fully depress the control knob and hold for 3-5 seconds. The burner should ignite and continue to operate when the control knob is released.
If the burner does not light or remain lit after 20 seconds of attempting ignition, turn the control valve to the OFF position and wait 5 minutes to allow gas to dissipate before attempting ignition again. DO NOT ATTEMPT TO LIGHT THE BURNER IF YOU SMELL GAS.
With burner lit and operating, the flame height can be adjusted between LOW and HIGH at any time.
WARNINGS
IMPORTANT
Please consult your Crystal Fire® Plus instruction manual for detailed
instructions and important information related to the burner installation
including lighting and operating instructions, safety information, and proper
tightening of connections with two wrenches.
DO NOT ATTEMPT TO INSTALL CRYSTAL FIRE® PLUS BURNER WITHOUT
FIRST CONSULT THE CRYSTAL FIRE® PLUS OWNER’S MANUAL.
WARNING
After consulting the manual and following instructions, remember: before
operating, all gas connections must be fully checked for leaks.
WARNING: This product can expose you to chemicals including Carbon Monoxide and Benzene which are known to the State of California to cause cancer or birth defects or reproductive harm. For more information, visit www.P65Warnings.ca.gov
Thank you for purchasing an Outdoor GreatRoom Company product! This fire pit was made with pride in the USA.
Warranty: Fire pit tables are covered under a 1-year manufacturer’s
warranty.
Please visit http://www.outdoorrooms.com/product-registration
to register your product.
References
- Fire Pits, Fire Pit Tables, Propane Fire Pits, Outdoor Fire Pits, Outdoor Kitchens & Patio Furniture - The Outdoor GreatRoom Company
- outdoorrooms.com/product-registration
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>