Barkan FS420 Fixed Floor Stand TV Mount Instruction Manual

Barkan FS420 Fixed Floor Stand TV Mount

Dimension

Consult a professional installer regarding the appropriate hardware needed according to your specific floor type.
Installation is the sole responsibility of the installer.

CAUTION! You are obligated to read the safety and assembly instructions! Disregarding them may lead to injury and to the falling of the electrical appliance.

WARNING! Barkan does not take responsibility for the installation.

Disregarding the safety and assembly instructions may result in the falling of, and/ or damage to your electrical appliance. Opening the package represents your undertaking to closely read and follow the instructions. When the product is installed in public places, the people in charge in those places should make sure it is used according to the instructions.

For Safety Instructions, warranty and further information, go to:www.barkanmounts.com > Support > Safety Instructions & Warranty
This mount is intended for use only with the maximum weight as indicated on the box. Using heavier products might cause injury.

ATTENTION! Please read the following

WARNING!
Consult a professional installer regarding the appropriate hardware needed according to your specific floor type. Installation is the sole responsibility of the installer.
For Safety Instructions, warranty and further information, go to:www.barkanmounts.com › Support › Safety Instructions & Warranty

Main Parts

Included Hardware not to scale

?

| 4
Z2| 6| 16| ?

?

| 4
Z3| 6| 25| 1| 4
Z4| 8| 25| 1| 4
Z5| 8| 45| 1 ?

?

| 4

Connect the TV plate to the back of the TV

1. Continue according to your TV mounting hole pattern
   

2. a. 75×75 mm up to 200X200 mm (inclusive) hole pattern
   

3. b. Hole pattern above 200×200 mm up to 600×400 mm:

4. Disassemble the screws
   

5. Connect the 4 adaptors to the TV plate, and reassemble the screws
   
   Position the adaptors according to your TV’s hole pattern
   Connect the TV Plate with the Adaptors to the TV in all 4 connection holes
   

6. Connect the lower pipe to the floor plate
   

7. Consult a professional installer regarding the appropriate hardware needed according to your specific floor type.
   Installation is the sole responsibility of the installer.
   
   We recommend using the 5 marked connection points
   

For illustration purpose only

4. Slide P10 to the bottom of the lower pipe.

5. Place P11 on the top of the lower pipe.

6. Slide the upper pipe into the lower pipe.
   

7. Pass the cables through the pipes.
   

8. Adjust the stand to the desired height and connect the screws
   

9. Place two nuts (Z8) in each of the two nut-housings (P2).

10. Attach the nut-housings (P2) on to part S. Make sure that the tab is inserted into the slot.
    

11. Push parts P3 down on the nut-housings (P2). The upside down “T” must pass the protruding tooth (shown below).
    

12. Floor connection test
    Apply force on the upper part of the product and make sure it is assembled properly.
    Carefully shake the product and make sure it is well connected to the floor.
    

13. Connect the TV Plate with the TV to the upper pole
    

14. In order to secure the TV, insert and tighten 2 screws on each side of the stand.
    Tighten the screws in order to create the necessary friction for the tool-free tilt mechanism.
    

15. Level the TV
    

BACKSCREEN CONNECTION POSITIONING OPTIONS

www.barkanmounts.com/faq

Customer Service

For more information: barkanmounts.com

If you are satisfied with the product, please give us a 5 stars rating on the website you bought it from. If you are not satisfied please contact us at https://www.barkanmounts.com/support and we will solve the problem for you.

CAUTION
This Mount is intended for use only with the maximum weight indicated.
Using heavier products might cause injury.

References

• Barkan Mounts
• Barkan Mounts
• Support | Barkan Mounts

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>