HUSKY N2R361872W4B Heavy Duty Boltless Steel Garage Storage Shelving Unit Instruction Manual
- October 30, 2023
- Husky
Table of Contents
4-SHELF STEEL SHELVING UNIT
36 in. W X 18 in. D X 72 in. H
US Patents &
Patents pending
Safety Information
WARNING
- This unit must be placed on a level surface or leveled with included hardware (when applicable).
- Do not sit or stand on or allow children to climb, sit or stand on the assembled product.
- For safety reasons, it is imperative that this unit be mounted on the wall or floor.
- Unit can tip over causing severe injury or death.
- Do not exceed the recommended weight limits.
- Evenly distribute the weight on each level and always keep the heavier loads on the bottom.
- Before cutting, drilling or hammering into any wall or floor surface, verify the location of electrical, plumbing and gas lines. Cutting may cause serious injury.
- Contains small parts, keep children away during installation.
- Use two or more people to assemble and move the unit to avoid injury.
- Use care when working with metal parts, wear gloves for protection.
- Do not use this unit to store aquariums.
- Maximum weight capacity per shelf is 1,000 lbs. (453.5 kg) when weight is evenly distributed; or 4,000 lbs. (1814.3 kg) total unit capacity, evenly distributed.
- Do not use this unit for anything other than the manufacturer’s intended purpose.
- Periodically inspect the unit to ensure all braces and beams are properly secured into the slots of each post.
- Keep this manual for future reference.
Contents
PARTS LIST
| PART | PART NUMBER |
|---|---|
| A | N2R-PS36-BLK |
| B | N2R-BR18-BLK |
| C | N2R-BM36-BLK |
| D | 1836W-B-V2 |
| E | MRWHOOK |
| F | CPOUT-BLK |
| G | FP-HP |
| H | RL-PC-B1.4 |
| I | ATHKIT |
Preparation
Before beginning assembly, read though the instructions and make sure all parts are present. Assembly of this unit is done by fitting the tabs located on each end of the braces (B) and beams (C) into the slots of the post (A). The narrow end of the post slots must face down. Braces and beams must be installed with the recessed ledge facing up on the inside. (See FIG.1). Assemble the unit from bottom to top. It is recommended that the bottom shelf assembly be installed starting at the second slot at the bottom of the posts, the middle shelves be evenly spaced, and finally the top shelf be installed using the first and second slots from the top of the posts. A rubber mallet may be used to tap down on the top of the braces and beams to properly secure the tabs down into the narrow end of the post slots (see FIG. 2 and FIG. 3). A visual inspection should be made to ensure that all the tabs are properly engaged into the narrow end of the post slots.
Helpful tools/items for assembly (not included):
| Rubber mallet
---|---
| Gloves
Preparation Continued
ALTERNATE ASSEMBLY
This unit can also be assembled as two separate 36 in. high units, each with
two shelf levels (see FIG. 4). If choosing this option, follow assembly steps
2, 3, 4, 5 and 6 until all shelf levels are completed for both units. Note:
Post Coupler (F), Post Foot (G) and Post Cap (H) are not used for this setup.
Assembly
Assemble G (x4) to A (x4)
Assemble B (x2) to posts
Note: make sure each pair of braces (B) are installed at the same height on each set of posts (A). Do this by simply counting the number of slots that the first brace is installed at, then install the second brace at the same slot count on the opposite two posts. (This will continue for each round of shelf level installations).
Assemble C (x2) to posts
Note: make sure each pair of beams (C) are installed at the same height
as the previous installed set of braces on each set of posts. This will ensure
each shelf will be leveled.
(This will continue for each round of shelf level installations).
Assembly Continue
Assemble D (x1)
NOTE: Wire decks (D) should be installed with the long horizontal wires
facing the bottom.
Assemble E (x2)
Assemble next shelf level by repeating same steps as 2, 3, 4 and 5 at the desired location
Assemble F (x4) to the assembled four posts
Note: A rubber mallet may be used to help secure the post couplers halfway onto the posts by lightly tapping down on the post coupler once it is attached to the post.
Assemble A (x4) to the four assembled post couplers
Note: A rubber mallet may be used to help secure the top posts into the post couplers by lightly tapping down on the post once it is attached to the post coupler.
Assemble the final two shelf levels by repeating same steps as 2, 3, 4 and 5 at the desired location, using B (x2), C (x2), D (x1) and E (x2) per level
Assemble H (x4) to the top of the assembled four posts
Warranty
GUARANTEED FOREVER. If your Husky product ever fails bring it back and we will replace it for free. This full warranty gives you specific rights which vary from state to state. If this product is defective contact the manufacturer for repair or replacement parts.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>