HUSKY N2R482478W5B 5 Shelf Steel Shelving Unit User Guide
- October 30, 2023
- Husky
Table of Contents
5-SHELF STEEL SHELVING UNIT
48 in. W X 24 in. D X 78 in. H
1.21 m AN X 60.9 cm PR X 1.98 m AL
US Patents & Patents pending
| ITEMS | MODELS |
|---|---|
| 1007587697 | N2R482478W5B |
| 1007587685 | N2R482478W5R |
USE AND CARE GUIDE
Questions, problems, missing parts? Contact us directly for assistance: 7 a.m.
– 5 p.m., CST, Monday-Friday
Chat: www.edsal.com
Email: [email protected]
Phone: 1-773-475-3131
To obtain replacement parts please provide: Model Number, Part Number &
Description, Store Location and Date Purchased.
Safety Information
WARNING
- This unit must be placed on a level surface or leveled with included hardware (when applicable).
- Do not sit or stand on or allow children to climb, sit or stand on the assembled product.
- For safety reasons, it is imperative that this unit be mounted on the wall or floor.
- Unit can tip over causing severe injury or death.
- Do not exceed the recommended weight limits.
- Evenly distribute the weight on each level and always keep the heavier loads on the bottom.
- Before cutting, drilling or hammering into any wall or floor surface, verify the location of electrical, plumbing and gas lines. Cutting may cause serious injury.
- Contains small parts, keep children away during installation.
- Use two or more people to assemble and move the unit to avoid injury.
- Use care when working with metal parts, wear gloves for protection.
- Do not use this unit to store aquariums.
- Maximum weight capacity per shelf is 1,000 lbs. (453.5 kg) when weight is evenly distributed; or 5,000 lbs. (2267.9 kg) total unit capacity, evenly distributed.
- Do not use this unit for anything other than the manufacturer’s intended purpose.
- Periodically inspect the unit to ensure all braces and beams are properly secured into the slots of each post.
- Keep this manual for future reference.
Contents
| | | |
---|---|---|---|---
PARTS LIST
| ITEMS: 1007587697
MODELS/MODELOS:
N2R482478W5B| ITEMS: 1007587685
MODELS/MODELOS:
N2R482478W5R
---|---|---
PART| PART NUMBER| PART NUMBER
A| N2R-PS39-BLK| N2R-PS39-RED
B| N2R-BR24-BLK| N2R-BR24-RED
C| N2R-BM48-BLK| N2R-BM48-RED
D| 2448W-BLK| 2448W-BLK
E| MRWHOOK| MRWHOOK
F| CPOUT-BLK| CPOUT-RED
G| FP-HP| FP-HP
H| RL-PC-B1.4| RL-PC-B1.4
I| ATHKIT| ATHKIT
Preparation
Before beginning assembly, read though the instructions and make sure all parts are present. Assembly of this unit is done by fitting the tabs located on each end of the braces (B) and beams (C) into the slots of the post (A). The narrow end of the post slots must face down. Braces and beams must be installed with the recessed ledge facing up on the inside. (See FIG.1). Assemble the unit from bottom to top. It is recommended that the bottom shelf assembly be installed starting at the second slot at the bottom of the posts, the middle shelves be evenly spaced, and finally the top shelf be installed using the first and second slots from the top of the posts. A rubber mallet may be used to tap down on the top of the braces and beams to properly secure the tabs down into the narrow end of the post slots (see FIG. 2 and FIG. 3). A visual inspection should be made to ensure that all the tabs are properly engaged into the narrow end of the post slots.
| 
| 
---|---|---
Helpful tools/items for assembly (not included):
ALTERNATE ASSEMBLY
This unit can also be assembled as two separate 39 in. high units (see FIG.
4). One unit will have three shelves and the other will have two shelves. If
choosing this option, follow assembly steps 2, 3, 4, 5 and 6 until all shelf
levels are completed for both units. Note: Post Coupler (F), Post Foot (G) and
Post Cap (H) are not used for this setup.
Assembly
-
Assemble G (x4) to A (x4)
-
Assemble B (x2) to posts
Note: make sure each pair of beams (C)
are installed at the same height as the previous installed set of braces on
each set of posts. This will ensure each shelf will be leveled. (This will
continue for each round of shelf level installations). -
Assemble C (x2) to posts
Note: make sure each pair of beams (C)
are installed at the same height as the previous installed set of braces on
each set of posts. This will ensure each shelf will be leveled.
(This will continue for each round of shelf level installations). -
Assemble D (x1
-
Assemble E (x2)
-
Assemble next shelf level by repeating same steps as 2, 3, 4 and 5 at the desired location
-
Assemble F (x4) to the assembled four posts
Note: A rubber mallet may be used to
help secure the post couplers halfway onto the posts by lightly tapping down
on the post coupler once it is attached to the post. -
Assemble A (x4) to the four assembled post couplers
Note: A rubber mallet may be used to
help secure the top posts into the post couplers by lightly tapping down on
the post once it is attached to the post coupler. -
Assemble the final three shelf levels by repeating same steps as 2, 3, 4 and 5 at the desired location, using B (x2), C (x2), D (x1) and E (x2) per level
-
Assemble H (x4) to the top of the assembled four posts
Warranty
GUARANTEED FOREVER. If your Husky product ever fails bring it back and we will replace it for free. This full warranty gives you specific rights which vary from state to state. If this product is defective contact the manufacturer for repair or replacement parts.