V I V O STAND-TV75BH Black Corner TV Stand with Dark Walnut Shelves Instruction Manual

: October 30, 2023
: V I V O

Table of Contents

V I V O STAND-TV75BH Black Corner TV Stand with Dark Walnut Shelves
Product Information
WARNING
PACKAGE CONTENTS
TOOLS NEEDED
ASSEMBLY STEPS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

V I V O STAND-TV75BH Black Corner TV Stand with Dark Walnut Shelves

V-I-V-O-STAND-TV75BH-Black-Corner-TV-Stand-with-Dark-Walnut-Shelves-
PRODUCT

Product Information

The Black Corner TV Stand with Dark Walnut Shelves is a sturdy and stylish TV stand that can hold up to 88 lbs (40 kg) of weight for the TV and 22 lbs (10 kg) of weight for the shelf. The package includes all the necessary hardware and tools for assembly, including a bubble level, Allen wrenches, and a wrench. It also comes with a VESA plate and brackets for easy attachment of the TV.

WARNING

If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use. CHOKING HAZARD SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

PACKAGE CONTENTS

V-I-V-O-STAND-TV75BH-Black-Corner-TV-Stand-with-Dark-Walnut-Shelves-
FIG-1

DO NOT EXCEED WEIGHT CAPACITY. Failure to do so may result in serious injury.

NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED

TOOLS NEEDED

Phillips Screwdriver

TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF TV OR STAND.
USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL

USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

ASSEMBLY STEPS

Connect Front Leg (D) to Right Back Leg (A) and Left Back Leg (B) using M6x12mm Screws (S-C) with 4mm Allen Wrench (T-B).
NOTE: Do not fully install screws; they will be fully tightened in a later step.
Slide Upper Support (C) on to leg assembly, making sure to match up the holes with Right Back Leg (A) and Left Back Leg (B). Secure using M6x12mm Screws (S-C) and 4mm Allen Wrench (T-B).
NOTE: Do not fully install screws; they will be fully tightened in a later step.
Install Shelf Clips (M) to underside of Large Shelf (E) at a 45° angle facing inward, using M6x12mm Screws (S-C) and 4mm Allen Wrench (T-B). Insert Shelf Spacers (N) into the ends of Large Shelf (E).
- Snap shelf assembly to the raised curves of assembled base as shown below.
- Secure Large Shelf (E) to frame assembly using M6x60mm Screws (S-A) and 4mm Allen Wrench (T-B). Use 4mm Allen Wrench (T-B) to fully secure and tighten previously installed screws.
Assemble Left Shelf Bracket (K) and Right Shelf Bracket (L) to Small Shelf (F) using M6x12mm Screws (S-C) and 4mm Allen Wrench (T-B).
NOTE: Do not overtighten screws.
- Insert two M6x12mm Screws (S-C) into the bottom inner holes on the frame assembly as show below, using 4mm Allen Wrench (T-B), making sure to leave 5mm of threads exposed. Place shelf assembly over installed screws.
- Secure shelf assembly to the frame using M6x12mm Screws (S-C) in the remaining inner holes with 4mm Allen Wrench (T-B). Tighten all previously installed M6x12mm Screws (S-C) on the small shelf assembly using 4mm Allen Wrench (T-B).
Assemble Left VESA Bracket (H) and Right VESA Bracket (I) to back of TV using appropriate Screws (M-A thru M-D), M8 Washers (M-E), Spacers (M-F, M-G) and a Phllips screwdriver.
Place Bubble Level (T-A) on VESA Plate (G). Assemble VESA Plate (G) to Upper Support (C) in one of two postions as shown below using M8x55mm Screws (S-B), M8 Washers (S-D), M8 Nuts (S-E) and M8 Screw Caps (S-F). Secure using 5mm Allen Wrench (T-C) and Wrench (T-D).
Loosen the safety screws on Left VESA Bracket (H) and Right VESA Bracket (I) with a Phillips screwdriver, then place onto VESA Plate (G), as shown below. Retighten safety screws with a Phillips screwdriver once in place.
Secure Cable Clips (J) to the frame assembly and manage cables. Adjust the tilt as desired.

Love your new VIVO setup and want to share? Tag us in your photo!

Open Monday – Friday 7:00am – 7:00pm CST

Our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.

Tel: 309-278-5303, AVG. RESOLUTION TIME (within office hrs): 5M 4S

Web: www.vivo-us.com ,AVG. RESOLUTION TIME (within office hrs): < 15 M

E-mail: help@vivo-us.com AVG. RESPONSE TIME (within office hrs): 1HR 8M