V I V O MOUNT-VWKB1 Single Monitor Wall Mount Keyboard Tray Wall Mount Instruction Manual

October 30, 2023
V I V O

V I V O MOUNT-VWKB1 Single Monitor Wall Mount Keyboard Tray Wall Mount

WARNING
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.

TIPOVER WARNING

SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

  • NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF TV OR TV CART.
  • USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL

USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

PACKAGE CONTENTS

V I V O-MOUNT-VWKB1-Single-Monitor-Wall-Mount-Keyboard-Tray-Wall-Mount-
fig-2

NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED

DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.

WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

TOOLS NEEDED

ASSEMBLY STEPS

STEP 1: Loosen the screw on Wall Mount (A) and slide off VESA Plate (A1).V I V O-MOUNT-VWKB1-Single-Monitor-Wall-Mount-Keyboard-Tray-Wall-Mount-
fig-4

STEP 2: Place Wall Mount (A) against the wall at the desired location and mark drilling locations with a pencil. Use of a level is recommended. If mounting to wood, drill 1.75” (45mm) deep holes using a 3/32”
(2.5mm) drill bit. For drywall, drill holes using a 5/16” – 25/64” (8 – 10mm) drill bit, then thread Drywall Anchors (W-E) into the holes using a Phillips screwdriver. Mount the wall bracket using the ST4x30mm Screws (W-D), making sure the opening in the adjustable support is facing up.

STEP 3: Assemble VESA Plate (A1) to the back of the monitor using Screws (M-A or M-B) and M5 Washers (M-C).

STEP 4: Slide VESA Plate (A1) back into Wall Mount (A) and secure by retightening the screw. Raise the monitor by lifting up. To lower the monitor, raise it up to the highest setting, then slowly lower it.V I V O-MOUNT-VWKB1
-Single-Monitor-Wall-Mount-Keyboard-Tray-Wall-Mount-
fig-7

STEP 5

  • Wood Stud Installation
    Use Arm (B) to mark mounting locations. Use of a level and stud finder is recommended. Using a 3/16” (4.5mm) bit, drill holes 2.2” (55mm) deep. Secure Arm (B) to the wall using ST6.3x55mm Screws (W-A) and M6 Washers (W-C).

  • Brick/Concrete Installation
    Use Arm (B) to mark mounting locations. Using a 3/8” (10mm) bit, drill holes 2.4” (60mm) deep. Insert Concrete Anchors (W-B) into holes. Secure Arm (B) to the wall using ST6.3x55mm Screws (W-A) and M6 Washers (W-C).V I V O-MOUNT-
VWKB1-Single-Monitor-Wall-Mount-Keyboard-Tray-Wall-Mount-
fig-8

STEP 6: Insert Covers (G) into the mounting holes in Arm (B).


STEP 7: Assemble Keyboard Tray (C) using Keyboard Tray Bracket (D) with M4x8mm Screws (S-A) and a Phillips screwdriver.

STEP 8: Mount the keyboard tray assembly to Arm (B) using M4x12mm Flat Head Screws (S-B) and M4 Nuts (S-C). Tighten using Wrench (T-B) and a Phillips screwdriver.

STEP 9: Remove the adhesive backing from Wrist Pad (F) and place it on Keyboard Tray (C) along with Mouse Pad (E).

STEP 10: Route cables through the cable management channels in Arm (B). Adjust the tilt of Arm (B) using 6mm Allen Wrench (T-A). Adjust gas spring support in Arm (B) using 6mm Allen wrench (T-A), turning counter-clockwise increases support, and clockwise decreases.

Love your new VIVO setup and want to share? Tag us in your photo! @vivo_us
Open Monday – Friday 7:00am – 7:00pm CST,our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.

  • 309-278-5303
  • AVG. RESOLUTION TIME (within office hrs): 5M 4S
  • www.vivo-us.com
  • Chat live with an agent!
  • AVG. RESOLUTION TIME (within office hrs): < 15 M
  • help@vivo-us.com
  • AVG. RESPONSE TIME (within office hrs): 1HR 8M
    • 23% within < 15m
    • 38% within < 30m
    • 61% within < 1hr
    • 83% within < 2hr
    • 92% within < 3hr

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com

References

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

V I V O User Manuals

Related Manuals