VIESSMANN 3570 Emergency light Assembly kit Instruction Manual

: June 12, 2024
: VIESSMANN

Table of Contents

VIESSMANN 3570 Emergency light Assembly kit
Product Information
Usage Instructions
Safety instructions
Mounting
Connection
Technical data
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

VIESSMANN 3570 Emergency light Assembly kit

Product Information

Product Name: H0 Rundumleuchte (Rotating flashing light)
Model Number: 3570 (yellow LED), 3571 (blue LED)
Manufacturer: Viessmann Modelltechnik GmbH
Made in: Europe
Operating Voltage: Up to 16V AC/DC
Suitable for: Installation in H0 model vehicles

Usage Instructions

Important Information

Before using the product or installing it, carefully read and understand the provided user manual.
Keep the user manual for future reference.

Safety Instructions

Caution : Risk of injury!

This product has detailed reproduction and may have peaks, edges, and breakable parts. Use appropriate installation tools.
Electrical hazard: Never insert the connecting wires into a power socket. Regularly inspect the transformer for any damage and do not use it if damaged.
Ensure the power supply is switched off when mounting the device and connecting the cables.
Only use VDE/EN tested special model train transformers for power supply to prevent the risk of burning cables.

Using the Product for its Correct Purpose:

This product is intended for installation in H0 model vehicles.
It operates with a power supply of up to 16V AC/DC.
Use the product only in dry rooms.
Using the product for any other purpose is not approved and may result in damage. The manufacturer is not responsible for any damage caused by improper use.

Installation

Installation directly on the roof:

Apply a small amount of super glue to the bottom of the Rundumleuchte (Rotating flashing light) (see Fig. 2).
Arrange the cables inside the vehicle and secure them at various points using adhesive if necessary.

Installation using a bracket:

Arrange the cables inside the vehicle and secure them at various points using adhesive if necessary.

Connection

Connect the Rundumleuchte (Rotating flashing light) to the control electronics (see Fig. 9).
To place the control electronics under the layout board, drill a hole with a diameter of 4.5 mm below the vehicle (see Fig. 12).

Technical Specifications

Operating Voltage:

Up to 16V AC/DC Note: This is a model building item and not a toy. It is not suitable for children under the age of 14.
Keep these instructions for future reference.

Please refer to the Viessmann website for the latest version of the manual using the provided item number.

Important information
Please read this manual completely and attentively before using the product for the first time. Keep this manual. It is part of the product.

Safety instructions

Caution: Risk of injury!

Due to the detailed reproduction of the original and the in-tended use, this product can have peaks, edges and break-able parts. For installation tools are required.
Electrical hazard:
- Never put the connecting wires into a power socket! Reg-ularly examine the transformer for damage. In case of any damage, do not use the transformer!
- Make sure that the power supply is switched off when you mount the device and connect the cables! Only use VDE/EN tested special model train transformers for the power supply! The power sources must be protected to prevent the risk of burning cables.

Using the product for its correct purpose

This product is intended:

For installation in H0 model vehicles.
For operation with a power supply up to 16 V AC~ / DC=.
For operation in dry rooms only.

Using the product for any other purpose is not approved and is considered inappropriate. The manufacturer is not responsible for any damage resulting from the improper use of this product

Checking the package contents

Check the contents of the package for completeness:

Rotating flashing light with LED and control electronics
2 brackets
Manual

Mounting

Test the function prior to mounting. Follow Chapter 3.

Mounting directly onto the roof:

Drill a hole at the mounting site with a diameter of 2.5 mm (fig. 1).
Apply a little glue to the underside of the rotating flashing light (fig. 2).
Insert the cable through the hole and then fit in the flashing light (fig. 3).
Arrange the cables inside the vehicle and fasten them in some spots with a little glue, if necessary.

Mounting with a bracket:

Insert the cables through the adapter ring (fig. 4).
Plug the bracket into the adapter ring up to the stop (fig. 5). If needed, the bracket may be shortened.
Place the wires into the groove of the bracket (fig. 6)
Drill a hole at the mounting site with a diameter of 1.5 mm (fig. 7.1/7.2).
Insert the cables and the bracket from above through the hole. Fasten the flashing light with some glue to the mounting site (fig. 8.1/8.2).
Arrange the cables inside the vehicle and fasten them in some spots with a little glue, if necessary.

Connection

Connect the rotating flashing light with the control electronics (fig. 9).
Connect the control electronics acc. to fig. 10 to a model train transformer (item 5200).
Should you prefer to invert the running direction of the LEDs, just exchange 2 random wires between the flashing light and control electronics (fig. 9)
If the rotating flashing light works as desired, put the shrink tubes over the joints and heat them up shortly with a hot air gun or a gas lighter (fig. 11).
In order to hide the control electronics underneath the layout, drill a hole of 4.5 mm diam. beneath the vehicle (fig. 12).

Technical data

Operating voltage: max. 16 V AC~ / DC= (also for digital current)

NOTE : Model building item, not a toy! Not suitable for children under the age of 14 years! Keep these instructions

Do not dispose of this product through (unsorted) domestic waste, supply it to recycling instead. You will find the latest version of the manual on the Viessmann website using the item number.

Made in Europe