V I V O STAND-LIVE1M Mobile All-In-One Livestream Multi-Mount Floor Stand Instruction Manual
- October 30, 2023
- V I V O
Table of Contents
V I V O STAND-LIVE1M Mobile All-In-One Livestream Multi-Mount Floor Stand
SKU: STAND-LIVE1M
Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product. Instruction Manual https://vivo- us.com/products/stand-live1m
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
- help@vivo-us.com
- www.vivo-us.com
- Chat live with an agent!
- 309-278-5303
WARNING!
If you do not understand these directions, or if you have any doubts about
the safety of the installation, please call a qualified technician. Check
carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual. Do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper
mounting, incorrect assembly or inappropriate use.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
DO NOT EXCEED WEIGHT CAPACITY. Failure to do so may result in serious injury.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
TOOLS NEEDED
ASSEMBLY STEPS
STEP 1
Connect Legs (E) to Base (G) using M6x25mm Screws (S-B) and 5mm Allen
Wrench (T-B). Attach Casters (O) and Locking Casters (P) to Legs (E).
Secure assembled base to Adjustable Pole (A) using M6x20mm Screws (S-A) and
4mm Allen Wrench (T-A). 
Turn assembly over and adjust Caster (P) height using Wrench (T-C). Use side
tab on Locking Casters (P) to lock wheels in place during assembly of stand.
STEP 2
Slide Cable Clip x2 (H), Locking Pole Ring x4 (Q), Lower Arm x2 (I), and Dual
Connector (K) onto Adjustable Pole (A) following the order shown below.
Tighten set screw of Locking Pole Ring (Q) using 4mm Allen Wrench (T-A).
Height Adjustment
Twise the Height Adjuster (A1) on Pole (A) to raise or lower the Pole. Lock
into place by tightening the set screw on Locking Pole Ring (Q) directly above
Height Adjuster (A1) using 4mm Allen Wrench (T-A). 
Stand can now be customized as desired with mounting arms and accessories. The following steps give an example of how stand arms and accessories can be mounted.
CAUTION : Properly balance the left and right weight distribution of the arms to prevent tipping.
STEP 3
Connect Upper Arm (J) to right side Lower Arm (I), then install VESA Plate
(F) to Upper Arm (J). Secure by tightening set screws using 4mm Allen Wrench
(T-A).
STEP 4
Attach Upper Arm (J) to left side Lower Arm (I), and secure by tightening
set screws using 4mm Allen Wrench (T-A). Insert Threaded Connector (S) into
Upper Arm (J).
STEP 5
Connect Upper Arm (J) to Dual Connector (K), then connect a second Upper
Arm (J), as shown below. Install Threaded Connector (S) to Upper Arm
(J).Secure by tightening set screws using 4mm Allen Wrench (T-A).
STEP 6
Screw Ball Head (T) onto Threaded Connector (S), then screw Ring Light (B)
onto Connector.
STEP 7
Connect Mic Boom (C) to remaining mounting hole in Dual Connector (K).
Twist Mic Mount (N) onto Mic Boom (C). Optional: Mic Boom (C) can be desk
mounted using Mic Boom Clamp (M).
Mounting Microphone Holder
STEP 8
For VESA Plate (F), choose between Monitor or Laptop Holder.
Monitor: Attach Screws (M-A or M-B) and M5 Washers (M-C) in the top VESA holes on monitor, using a Phillips screwdriver. Slide onto VESA Plate (F) and attach remaining two Screws (M-A or M-B) and M5 Washers (M-C).
Laptop: Attach M4x8mm Screws (S-C) and M5 Washer (S-D) into Laptop Tray,
partially protruding, using Phillips screwdriver. Slide onto VESA Plate (F)
and attach remaining M4x8mm Screws (S-C) and M5 Washers (S-D).
Optional
VESA Plate (F) can be adjusted using 4mm Allen Wrench (T-A) to allow
monitor to tilt, turn, and swivel.
STEP 9
Twist Ball Head (T) onto Threaded Connector (S), then connect Phone/Tablet Holder (L).
NOTE: Ball Head (T) can also be used to mount cameras and other multi-
media devices.
STEP 10
Remove the bottom covers from Lower Arms (I) and Upper Arms (J) by sliding
off. Organize cables and slide covers back on.
THIS PAGE INTENTIONALLY LEFT BLANK
- Love your new VIVO setup and want to share? Tag us in your photo! @vivo_us LAST UPDATED: 11/09/2022 REV2
Open Monday – Friday 7:00 am – 7:00 pm CST,
our dedicated support team can offer immediate assistance with rapid response
times. If any parts are received damaged or defective, please contact us. We
are happy to replace parts to ensure you have a fully functioning product.
- 309-278-5303 AVG. RESOLUTION TIME (within office hrs): 5M 4S
- www.vivo-us.com
- Chat live with an agent!
- AVG. RESOLUTION TIME (within office hrs): < 15 M
- help@vivo-us.com
AVG. RESPONSE TIME (within office hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Mobile All-In-One Livestream Multi-Mount Floor Stand – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>