V I V O STAND-V003Y Triple Monitor Desk Mount Instruction Manual
- October 30, 2023
- V I V O
Table of Contents
V I V O STAND-V003Y Triple Monitor Desk Mount
SKU: STAND-V003Y/W
Scan the QR code with your mobile device or follow the link for helpful videos
and specifications related to this product.Instruction Manual
https://vivo-us.com/products/stand-v003y
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
WARNING!
If you do not understand these directions, or if you have any doubts about the
safety of the installation, please call a qualified technician. Check
carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual. Do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper
mounting, incorrect assembly or inappropriate
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT
TIPOVER:
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
- USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
TOOLS NEEDED
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury
ASSEMBLY STEPS
STEP 1
Attach Pole Cap (G) to top of Pole (D).
STEP 2 (Option A)
Clamp Installation
Mount Pole (D) to Clamp (C) with M6x16mm Screws (S-A) using 4mm Allen Wrench
(T-A). Apply
Rubber Pads (I) to bottom of Clamp (C), and secure it to the desktop.
STEP 2 (Option B)
Grommet Base Installation
Remove screw from Clamp Bolt (C1), and remove Clamp Bolt (C1) from Clamp (C).
Apply Rubber Pads (I) to bottom of Grommet Base (F). Align pin on top of
Grommet Base (F) with the small hole on the bottom of Pole (D), position over
hole in desktop, and install to desktop using Clamp Bolt (C1) and Support
Plate (H).
STEP 3
Install Arm (B) and Cable Clip (E) to Pole (D). Secure Arm (B) using 5mm
Allen Wrench (T-B)
STEP 4
For Flat Back Monitors, install VESA Plate (A) to monitor using Screws (M-A or
M-C) and M5 Washers (M-E).
For Curved Back Monitors, install VESA Plate (A) to monitor using Screws (M-B
or M-D), M5 Washers (M-E), and Spacers (M-F).
STEP 5
Slide the monitors with VESA Plates (A) onto the heads of Arm (B). Install
Thumbscrews (S-B). Make sure the screws are installed before you rotate the
monitors. If needed, adjust the tilt angle using 6mm Allen Wrench (T-C).
STEP 6
Manage the cables using the installed cable clips.
STEP 7
Adjust monitor alignment using 5mm Allen Wrench (T-B)
STEP 8
Be careful not to extend the arms too far forward or backward.
STEP 9
Store the Allen Wrenches in Cable Clip (E) for future use.
Love your new VIVO setup and want to share? Tag us in your photo! @vivo_us
Open Monday – Friday 7:00am – 7:00pm CST,
our dedicated support team can offer immediate assistance with rapid response
times. If any parts are received damaged or defective, please contact us. We
are happy to replace parts to ensure you have a fully functioning product.
www.vivo-us.com
Chat live with an agent! AVG.
RESOLUTION TIME (within office hrs): < 15 M
309-278-5303
AVG. RESOLUTION TIME (within office hrs): 5M 4S
help@vivo-us.com AVG. RESPONSE TIME (within office hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT:www.vivo- us.com
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Triple Monitor Desk Mount – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>