V I V O STAND-V002K Pneumatic Arm Dual Monitor Desk Mount Instruction Manual
- October 30, 2023
- V I V O
Table of Contents
Pneumatic Arm Dual Monitor Desk Mount
Instruction Manual
STAND-V002K Pneumatic Arm Dual Monitor Desk Mount
SKU: STAND-V002K,W
Scan the QR code with your mobile device or follow the link for helpful videos
and specifications related to this product.
https://vivo-us.com/products/stand-v002k
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
| help@vivo-us.com
---|---
| www.vivo-us.com
Chat live with an agent!
| 309-278-5303
WARNING!
If you do not understand these directions, or if you have any doubts about the
safety of the installation, please call a qualified technician. Check
carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual. Do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper
mounting, incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT
TIPOVER:
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
- USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
TOOLS NEEDED
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
DO NOT EXCEED WEIGHT
CAPACITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1
Loosen the screws and disassemble the Clamp (D) using the 4mm Allen Wrench
(T-A).
STEP 2
OPTION A: Clamp Installation
Attach Clamp Brace (D1) to Pole (C) using the M6x16mm Screws (S-B) and 4mm
Allen Wrench (T-A). Peel the protective film off of Soft Pad (G) and place it
onto Clamp Brace (D1).
OPTION B: Grommet Base
Installation For grommet hole attachment only, cut Soft Pad (G) along the
indentations. Peel the protective film off of Soft Pad (G) and place the
pieces onto the Grommet Base (F) as shown below.
OPTION A: Clamp Installation
For thinner desktops, re-attachClamp (D2) to Clamp Brace (D1) and tighten the
screws using 4mm Allen Wrench (T-A). For thicker desktops, disassemble the
Clamp (D2) using a Phillips screwdriver as shown in 3.1. Flip the L-bracket
over and reassemble. Then re-attach Clamp (D2) to Clamp Brace (D1) and tighten
the screws using 4mm Allen Wrench (T-A).
OPTION B: Grommet Installation
If not using an existing through-hole, using a 10mm (⅜”) drill bit, drill
through the desktop at least 2” away from the edge. Disassemble the Clamp (D2)
using a Philips screwdriver. Set aside all parts except for Clamp Bolt (D3).
Attach Pole (C) and Grommet Base (F) to the desktop using the Support Plate
(H) and Clamp Bolt (D3) as shown below.
While holding Arm (A) closed, cut the shipping tie and gently release (A).
STEP 3
Slide Arm (A) onto Pole (C) and tighten using 6mm Allen Wrench (T-B). Attach
Cable Clip (E) to Pole (C).
STEP 4
Attach VESA Plate (B) to the back of the monitor using Screws (M-A through
M-D) and Washers (M-E). If needed, use Spacers (M-F).
STEP 5
Slide VESA Plate (B) with monitor over bracket on Arm (A). Secure using the
Thumbscrew (S-A).
STEP 6
Adjust gas spring support in Arm (A) using 6mm Allen Wrench (T-B). Turning
counter-clockwise increases support, and clockwise decreases.
STEP 7
Remove bottom cover from Arm (A) by sliding it off. Organize cables and re-
attach cover.
STEP 8
Adjust tilt support using 6mm Allen Wrench (T-B). Store Allen Wrenches (T-A,
T-B) in Cable Clip (E).
Adjust as desired.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
LAST UPDATED: 12/22/2022
REV2.1
Open Monday – Friday 7:00am – 7:00pm CST,
our dedicated support team can offer immediate assistance with rapid response
times. If any parts are received damaged or defective, please contact us. We
are happy to replace parts to ensure you have a fully functioning product.
309-278-5303
AVG. RESOLUTION TIME (within office hrs): 5M 4S
www.vivo-us.com
AVG. RESOLUTION TIME (within office hrs): < 15 M
Chat live with an agent!
help@vivo-us.com
AVG. RESPONSE TIME (within office hrs): 1HR 8M
– 23% within < 15m
– 38% within < 30m
– 61% within < 1hr
– 83% within < 2hr
– 92% within < 3hr
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Pneumatic Arm Dual Monitor Desk Mount – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>