V I V O STAND-V032T Dual Monitor Extra Tall Desk Mount Instruction Manual
- October 30, 2023
- V I V O
Table of Contents
V I V O STAND-V032T Dual Monitor Extra Tall Desk Mount
Dual Monitor Extra Tall Desk Mount
The Dual Monitor Extra Tall Desk Mount is a sturdy and durable mount that allows you to mount two monitors on your desk. It has a weight capacity of 22 lbs per arm and can be installed using either the desk clamp or grommet option. The package contents include:
- A Lower Pole (x1)
- A Middle Pole (x1)
- An Upper Pole (x1)
- A Clamp (x1)
- Mount Arms (x1)
- VESA Plate (x2)
- Pole Cap (x1)
- Pole Cable Clip (x3)
- Cable Clip (x4)
- Soft Pad (x1)
- Support Plate Grommet Plate (x1)
- Grommet Plate (x1)
- Screw (M6x16mm) (x3)
- Security Nut (M6) (x2)
- Thumb Screw (M4x12mm) (x8)
- Screw (M4x30mm) (x8)
- Spacer (M6) (x8)
- Allen Wrench (3mm) (x1)
- Allen Wrench (5mm) (x1)
- Allen Wrench (6mm) (x1)
Usage Instructions
Step 1: Loosen the knob on Clamp (D).
Step 2:
- Option A – Desk Clamp: Connect Clamp (D) to Lower Pole (A) using M6x16mm Screws (S-A) and 3mm Allen Wrench (T-A). Place assembly on desktop and secure by tightening knob on Clamp (D).
- Option B – Grommet: Using a Phillips screwdriver, remove the screw from Clamp (D) and disassemble. Set Knob (D1) aside. Connect Grommet Plate (J) to Lower Pole (A) using M6x16mm Screws (S-A) and 3mm Allen Wrench (T-A). Remove adhesive backing from Soft Pad (K) and adhere to Grommet Plate (J). Place the pole assembly over the grommet hole in the desk, and connect using Support Plate (L) and previously removed Knob (D1) from underneath desk. Secure by tightening Hand Bolt (D1). For desktops without an existing grommet hole, use a 3/8 (10mm) drill bit to drill through the desktop, then secure assembly as previously described.
Step 3: Tighten and secure Middle Pole (B) to Lower Pole (A), then connect Upper Pole (C) to Middle Pole (B).
Step 4: Slide Pole Cable Clips (H) over pole assembly, then attach Mount Arms (E) and secure using 6mm Allen Wrench (T-C). Press Pole Cap (G) into pole assembly. Attach Cable Clips (I) to Monitor Arms (E) by snapping into place.
Step 5:
- Secure VESA Plates (F) to monitors using M4x12mm Thumbscrews (M-A) or M4x30mm Screws (M-B). M6 Spacers (M-C) may be required.
- Slide monitors with VESA Plates (F) onto Mount Arms (E). Secure VESA Plates (F) in place using M6 Security Nuts (S-B).
WARNING: This product has a weight capacity of 22 lbs per arm. Do not exceed this weight capacity as it may result in serious injury. Also, this product is not suitable for children under 3 years of age due to small parts. Adult supervision is required. If you have any questions or concerns, please contact us at help@vivo-us.com or call us at 309-278-5303 from Monday-Friday from 7:00am-7:00 pm CST. You can also chat live with an agent on our website www.vivo-us.com
SKU: STAND-V032T
Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product.
GET IN TOUCH | Monday-Friday from 7:00 am-7:00 pm CST
- help@vivo-us.com
- www.vivo-us.com Chat live with an agent!
- 309-278-5303
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
- USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
TOOLS NEEDED
DO NOT EXCEED WEIGHT CAPACITY. Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1
Loosen knob on Clamp (D), as shown below.
STEP 2: Option A – Desk Clamp Connect Clamp (D) to Lower Pole (A) using M6x16mm Screws (S-A) and 3mm Allen Wrench (T-A). Place assembly on desktop and secure by tightening knob on Clamp (D).
STEP 2: Option B – Grommet
Using a phillips screwdriver, remove the screw from Clamp (D) and disassemble.
Set Knob (D1) aside. Connect Grommet Plate (J) to Lower Pole (A) using M6x16mm
Screws (S-A) and 3mm Allen Wrench (T-A). Remove adhesive backing from Soft Pad
(K) and adhere to Grommet Plate (J).
Lower Pole (A) & Upper Pole (C) may look similar. To differentiate, match the hole pattern to images below. The holes on Lower Pole (A) are spaced closer together than Upper Pole (C).
Place the pole assembly over grommet hole in desk, and connect using Support Plate (L) and previously removed Knob (D1) from underneath desk, as shown. Secure by tightening Hand Bolt (D1). For desktops without an existing gromment hole, use a 3/8” (10mm) drill bit to drill through desktop, then secure assembly as previously described.
STEP 3
Tighten and secure Middle Pole (B) to Lower Pole (A), then connect Upper
Pole (C) to Middle Pole (B).
STEP 4
Slide Pole Cable Clips (H) over pole assembly, then attach Mount Arms (E)
and secure using 6mm Allen Wrench (T-C). Press Pole Cap (G) into pole
assembly.
Attach Cable Clips (I) to Monitor Arms (E) by snapping into place. 
STEP 5
Secure VESA Plates (F) to monitors using M4x12mm Thumbscrews (M-A) or
M4x30mm Screws (M-B). M6 Spacers (M-C) may be required.
Slide monitors with VESA Plates (F) onto Mount Arms (E). Secure VESA Plates
(F) in place using M6 Security Nuts (S-B).
STEP 6
Route cables through Cable Clips (I) and Pole Cable Clips (H).
STEP 7
Adjust the monitor tilt using 5mm Allen Wrench (T-B). To level monitors,
remove M6 Security Nuts (S-B) and tighten or loosen adjustment screws using
3mm Allen Wrench (T-A). Once level, fasten M6 Security Nuts (S-B) back into
place.
- Love your new VIVO setup and want to share? Tag us in your photo! @vivo_us LAST UPDATED: 11/16/2022 REV1.1
Open Monday – Friday 7:00am – 7:00pm CST,
our dedicated support team can offer immediate assistance with rapid response
times. If any parts are received damaged or defective, please contact us. We
are happy to replace parts to ensure you have a fully functioning product.
- 309-278-5303 AVG. RESOLUTION TIME (within office hrs): 5M 4S
- www.vivo-us.com
- Chat live with an agent! AVG. RESOLUTION TIME (within office hrs): < 15 M
- help@vivo-us.com
- AVG. RESPONSE TIME (within office hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Dual Monitor Extra Tall Desk Mount up to 32" Screens – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>