ZALMAN i3 Series ATX Mid Tower Computer Case User Manual

: June 4, 2024
: ZALMAN

Table of Contents

ZALMAN i3 Series ATX Mid Tower Computer Case User Manual
Precautions
Specification
Accessories Component
1/O Port
1. Separating the side panel
2. Mounting the main board
3. Mounting PCI-E (VGA) card
4. Mounting 2.5″ SSD and HDD
5. Mounting the 3.5″ and 2.5″ HDD
6. Cable Connection
7. Mounting the top fan
8. Mounting the fan and radiator in the front
- References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ZALMAN i3 Series ATX Mid Tower Computer Case User Manual

ZALMAN i3 Series ATX Mid Tower Computer Case

i3 Series

To ensure safe and easy installation, please read the following precaution.
Product design and specifications may be revised to improve quality and performance.

www.ZALMAN.COM

Precautions

Read this manual carefully before installing.
Check the product and components before installing. If you find any abnormality, contact the location where you purchased the product for a replacement or refund.
Wear gloves to prevent accidents when installing the product.
Severe damage may occur when mounting the system, so do not apply excessive force.
Connecting the cable incorrectly may cause a fire due to a short circuit. Make sure to refer to the manual when connecting the cable.
Be careful not to block the ventilation hole of the product when using the system.
Avoid locations with direct sun ight, water, moisture, oil, and excessive dust. Store and use the product in a well-ventilated location.
Do not wipe the surface of the product using chemicals. (organic solvents such as alcohol or acetone)
Do not insert your hand or other object into the product during operation, as this may injure your hand or damage the object
Store and use the product out of children’s reach.
Our company assumes no responsibility for any problem that occurs due to the use of the product for purposes other than its designated purposes and/or the carelessness of the consumer.
The exterior design and specifications of the product are subject to change without prior notice to consumers for quality improvement.

Specification

FIG 1 Specification

FIG 2 Specification

Accessories Component

FIG 3 Accessories Component

1/O Port

FIG 4 1 O Port

1. Separating the side panel

Side Panel Removal

FIG 5 Side Panel Removal

2. Mounting the main board

As 6 stand-offs are mounted by default, insert an additional standoff according to the type of main board by referring to the mounting position of the main board, and mount the main board on the case.

FIG 6 Mounting the main board

FIG 7 Mounting the main board

3. Mounting PCI-E (VGA) card

Loosen the screw, separate the PCI cover, mount the graphic card, and fix it using the screw.

$FIG 8 Mounting PCIE $VGA$ card$

4. Mounting 2.5″ SSD and HDD

2.5″ HDD and SSDs can be installed on the right side of case as shown in the diagram below.

FIG 9 Mounting 2.5 SSD and HDD

5. Mounting the 3.5″ and 2.5″ HDD

Separate the tool-free 2.5″ and 3.5″ combo HDD cage and assemble the HDD or SSD. Mount the assembled HDD on the slot.

FIG 10 Mounting the 3.5 and 2.5 inch HDD

6. Cable Connection

FIG 11 Cable Connection

7. Mounting the top fan

As shown in the picture, install the fan on the top of the case using bolts

FIG 12 Mounting the top fan

8. Mounting the fan and radiator in the front

After Front Cover Removal and Mount the fan or the radiator on the mount hole in the front as shown in the figure.
(For liquid-coders, only products with a hose length of 280 mm or more can be installed)

FIG 13 Mounting the fan and radiator in the front