V I V O STAND-V013L Black Dual Monitor + Single Laptop Desk Mount Instruction Manual
- October 30, 2023
- V I V O
Table of Contents
Black Dual Monitor + Single Laptop Desk Mount
Instruction Manual
SKU: STAND-V013L
Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product.
https://vivo-us.com/products/stand-v013L
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
| |
---|---|---
help@vivo-us.com| www.vivo-us.com
Chat live with an agent!| 309-278-5303
WARNING!
If you do not understand these directions, or if you have any doubts about the
safety of the installation, please call a qualified technician. Check
carefully to make sure there are no missing or defective parts.
Improper installation may cause damage or serious injury. Do not use this
product for any purpose that is not explicitly specified in this manual. Do
not exceed weight capacity. We cannot be liable for damage or injury caused by
improper mounting, incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT
TIPOVER:
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
- USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
NOTE: SOME HARDWARE MAY NOT BE USED
TOOLS NEEDED
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1
OPTION A: Clamp Installation
Install Upper Clamp (C) to Pole (G) using M6x16mm Screws (S-B) and 4mm Allen
Wrench (T-A). Apply Pads (N) to the underside of Upper Clamp (C) as shown
below. Then attach Lower Clamp (D) to Upper Clamp (C) using M6x10mm Screws
(S-A) and 5mm Allen Wrench (T-B) using either the top or bottom holes in Upper
Clamp, based on desktop thickness. Secure the clamp assembly to the desktop by
tightening to the hand bolts on Lower Clamp (D).
OPTION B: Existing Grommet Base Installation
The gromment installation will make use of one Hand Bolt (D1) from Lower Clamp
(D). To remove, use a Phillips screwdriver to remove the small screw from the
top of Hand Bolt (D1) and unscrew Hand Bolt (D1) from Lower Clamp (D). Apply
Pads (N) to Grommet Plate (J). Place the pole assembly over grommet hole in
desk, and connect using Support Plate (M) and previously removed Hand Bolt
(D1) from underneath desk, as shown. Secure by tightening Hand Bolt (D1).
STEP 2 (Option A)
SIDE LAPTOP MOUNTING:
Slide Pole Cable Clip (L) onto the Pole (G). Assemble Laptop Arm (B), Monitor
Arm (A), and VESA Bracket (E) on to Pole (G) and secure using 5mm Allen Wrench
(T-B).
STEP 2 (Option B)
CENTER LAPTOP MOUNTING:
Slide Pole Cable Clip (L) onto the Pole (G). Assemble VESA Bracket (E),
Monitor Arm (A) and Laptop Arm (A), and on to Pole (G) and secure using 5mm
Allen Wrench (T-B).
STEP 3
Install Arm Cable Clips (K) to Monitor Arm (A) and Laptop Arm (B).
STEP 4
Install two mounting screws (M-A or M-B) with Washers (M-C) onto top holes of
each monitor, leaving a 3mm gap. Slide monitors onto respective Mount Arm (A)
and VESA Mount (E) and insert two mounting screws (M-A or M-B) with Washers
(M-C) into remaining holes and tighten using a Phillips screwdriver.
STEP 5
Place Laptop Arms (H) underneath each side of Laptop Tray (F), aligning square
holes in Laptop Arms (H) with the edge and long slot on each side. Insert
Clips (I) through top to secure Laptop Arms (H), making sure all four locks on
each Clip (I) are engaged with square holes in Laptop Arms (H).
Insert two M4x8mm Screws (S-C) into the top holes of Laptop Tray (F), leaving a 3mm gap. Slide Laptop Tray (F) onto Laptop Arm (B) VESA plate and tighten screws. Install final two M4x8mm Screws (S-C) into bottom VESA holes to secure.
STEP 6
Adjust tilt on Mount Arm (A) and Laptop Arm (B) using 6mm Allen Wrench (T-C).
To level height of monitors, use 5mm Allen Wrench (T-B).
STEP 7
Route cables through Arm Cable Clips (K) and Pole Cable Clip (L). Store 5mm
Allen Wrench (T-B) and 6mm Allen Wrench (T-C) in Pole Cable Clip (L) for
future adjustments.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
Open Monday – Friday 7:00am – 7:00pm CST,
our dedicated support team can offer immediate assistance with rapid response
times. If any parts are received damaged or defective, please contact us. We
are happy to replace parts to ensure you have a fully functioning product.
| |
---|---|---
help@vivo-us.com| www.vivo-us.com
Chat live with an agent!| 309-278-5303
AVG. RESPONSE TIME (within office hrs): 1HR 8M
– 23% within < 15m
– 38% within < 30m
– 61% within < 1hr
– 83% within < 2hr
– 92% within < 3hr
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Black Dual Monitor + Single Laptop Desk Mount – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>