zalman T3 Plus Matx Mini Tower Computer Case User Manual

: June 16, 2024
: ZALMAN

zalman T3 Plus Matx Mini Tower Computer Case

Developed and designed by ZALMAN in Korea.
This product is protected by ZALMAN’s pending or registered patents.

To ensure safe and easy installation, please read the following precautions.
Product design and specifications may be revised to improve quality and performance without notice.

Precautions

Read this manual carefully before installing.
Check the product and components before installing. If you find any abnormality, contact the location where you purchased the product for a replacement or refund.
Wear gloves to prevent accidents when installing the product.
Severe damage may occur when mounting the system, so do not apply excessive force.
Connecting the cable incorrectly may cause a fire due to a short circuit. Make sure to refer to the manual when connecting the cable.
Be careful not to block the ventilation hole of the product when using the system.
Avoid locations with direct sunlight, water, moisture, oil, and excessive dust. Store and use the product in a well-ventilated location.
Do not wipe the surface of the product using chemicals. (organic solvents such as alcohol or acetone)
Do not insert your hand or other object into the product during operation, as this may injure your hand or damage the object.
Store and use the product out of children’s reach.
Our company assumes no responsibility for any problem that occurs due to the use of the product for purposes other than its designated purposes and/or the carelessness of the consumer.
The exterior design and specifications of the product are subject to change without prior notice to consumers for quality improvement.

Specifications

Model	T3 PLUS
Case Form Factor	mATX Mini-Tower
Dimensions	355 x 206 x 422(H)mm
Weight	3.6kg
Case Materials	Plastic, Steel, Tempered Glass
Motherboard Support	mATX / Mini-ITX
Maximum VGA Length	290mm
Maximum CPU Cooler Height	150mm
Maximum PSU Length	140mm
PCI Expansion Slots	4
Drive Bays	1 x Combo (3.5″ or 2.5′; 1 x 3.5″), 1 x SSD (2.5″)
Fan Support	Top
Front	3 x 120mm/2 x 140mm
Rear	1 x 120mm
Bottom	2 x 120mm
Fan(s) Included	Front
Rear	1 x 120mm
Radiator Support	Front
I/O Ports	1 x Headphones, 1 x MIC, 2 x USB2.0, 1 x USB3.0,

Reset Button, Power Button

Dimension

Accessories Component

I/O Ports

Removing the side panels

Tempered Glass
Steel Panel

Removing the front panel

Mounting the motherboard

Mounting the Motherboard

Motherboard size

Motherboard Size

Mounting PCI-E(VGA) card

$Mounting PCI-E$VGA$ Card$

Mounting the 2.5″ SSD

Mounting the 2.5" SSD

Mounting the 3.5″ and 2.5″ SSD / HDD

Mounting the 3.5" and 2.5" SSD / HDD

Mounting the PSU

Mounting the radiator

Mounting the front radiator
- 1 x 120mm

Mounting the fans

Mounting the top fans
- 2 x 120mm
Mounting the front fans
- 3 x 120mm, 2 x 140mm
Mounting the rear/bottom fan
1 x 120mm/2x120mm

Fan(S) Included / Fan Specifications

120mm Black Fan	Top / Rear
Dimensions	120 x 120 x 25(T)mm
Bearing	Sleeve Bearing
Input	DC 12V
RPM	1200RPM±10%
Fan	3-Pin
LED	–

I/O Connectors

Certification

This mark, designed by Zalman, indicates product compliance with the European Union’s RoHS (Restriction of Hazardous Substances) Directive.

Disposal of Old Electrical & Electronic Equipment
(Applicable in the European Union and other European countries with separate collection systems)

www.zalman.com