VAXCEL Cascadia T0685 Winfield 1 Light Dusk to Dawn Matte Black Outdoor Wall Lantern Instruction Manual

VAXCEL Cascadia T0685 Winfield 1 Light Dusk to Dawn Matte Black Outdoor

Wall Lantern

Product Information

The T0685 is a light fixture that has a photocell function to enable the light to turn on at dusk and off at dawn automatically. It requires a maximum of 60W Type ST Bulb (not included) and is compatible with a dimmer switch when the photocell is disconnected. The fixture comes with a hardware package that includes a mounting plate unit, mounting screw, wire connector, bolt nut, rubber pad, glass shade, and fixture wire backplate.

Product Usage Instructions

1. Before installing the T0685 light fixture, turn off the main power at the circuit breaker.
2. Consult local electrical codes for wiring and grounding requirements before installing.
3. Read and save the assembly and installation instructions for future reference.
4. Attach the mounting plate unit (A) to the outlet box by using two mounting screws (B). Adjust the length of the preinstalled fixture mounting screws if necessary. Ensure that two fixture mounting screws are lined up horizontally to make the fixture level.
5. Install the bulb (not included). See relamping label at socket area or packaging for maximum wattage allowed.
6. Attach the backplate of the fixture to the mounting plate unit (A) by aligning and inserting the two fixture mounting screws into set holes on backplate, then secure it with two rubber pads (E) and two bolt nuts (D). Use silicone caulk compound to caulk completely around where the backplate meets with the wall surface to prevent water from seeping into the outlet box.
7. To disconnect Dusk-to-Dawn Photocell, turn off the power at the fuse or circuit box before starting installation.
8. Loosen the wire connector connected to the wires from the photocell. Do not remove the photocell to prevent water from seeping into the outlet box.
9. Take a white pigtail and a black pigtail and make wire connections using wire connector (C): a. The black wire from the fixture to one end of the black pigtail. b. The white wire from the fixture to one end of the white pigtail. c. The other end of the black pigtail to the black wire from the power source. d. The other end of the white pigtail to the white wire from the power source. Put all wires back into the backplate of the fixture.
10. Turn on the power at the fuse or circuit box.

Spare Parts List

The following parts are available for re-order if damaged or missing:

• Mounting Plate Unit (A)
• Mounting Screw (B)
• Wire Connector (C)
• Bolt Nut (D)
• Rubber Pad (E)
• Glass Shade
• Fixture Wire Backplate

ASSEMBLY AND INSTALLATION INSTRUCTIONS

WARNING: Turn off the main power at the circuit breaker before installing the fixture.

AVERTISSEMENT: Coupez la source d’alimentation principale au panneau central de disjoncteurs avant d’installer le luminaire.

NOTE

1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.

Hardware Package (included)

IMPORTANT:
The sensor has an excellent photocell function to enable the light to turn on at dusk and off at dawn automatically.

Installation Steps

Turn off the power at fuse or circuit box.

1. Unscrew the two bolt nuts (D), remove the two rubber pads (E) and the mounting plate unit (A) from the backplate.

2. Attach the mounting plate unit (A) to the outlet box by using two mounting screws (B). Adjust the length of the preinstalled fixture mounting screws if necessary.
   Note: Make sure that two fixture mounting screws are lined up horizontally to make the fixture level.

3. Pull out the source wires from the outlet box. Make wire connections using wire connectors (C) as follows:

   • Connect the hot wire (black insulation) from the fixture to the black wire from the power source.
   • Connect the neutral wire (white insulation) from the fixture to the white wire from the power source.
   • Attach the fixture ground wire (bare wire) to the mounting plate unit (A) with a green ground screw, then depending on the local code, connect it to the house ground wire with the wire connector (C). Carefully put all of the wires back into the outlet box.

4. Install the bulb (not included). See relamping label at socket area or packaging for maximum wattage allowed.

5. Attach the backplate of the fixture to the mounting plate unit (A) by aligning and inserting the two fixture mounting screws into set holes on the backplate, then secure it with two rubber pads (E) and two bolt nuts (D).
   Note: With silicone caulk compound, caulk completely around where the backplate meets with the wall surface to prevent water from seeping into the outlet box.

Turn on the power at fuse or circuit box.

Optional Installation

Disconnect Dusk-to-Dawn Photocell

IMPORTANT:
Compatible with dimmer when the photocell is disconnected. Requires dimmable bulb and compatible dimmer switch.

1. Turn off the power at the fuse or circuit box before starting installation.

2. Loosen the wire connector connected to the wires from the photocell. (See Fig.1)
   Note: Do not remove the photocell to prevent water from seeping into the outlet box.

3. Take a white pigtail and a black pigtail and make wire connections using wire connector (C): (See Fig.2)

   • The black wire from the fixture to one end of the black pigtail.
   • The white wire from the fixture to one end of the white pigtail.
   • The other end of the black pigtail to the black wire from the power source.
   • The other end of the white pigtail to the white wire from the power source.
   • Put all wires back into the backplate of the fixture.

Turn on the power at the fuse or circuit box.

The following parts are available for re-order if damaged or missing.

Spare Parts List

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>