VAXCEL T0646 Kilbourne 1-Light 13 Inch Textured Black Outdoor Wall Light Instruction Manual

T0646 Kilbourne 1-Light 13 Inch Textured Black Outdoor Wall Light

Product Information

The T0646 is a wall-mounted light fixture that requires assembly and installation. It comes with a mounting plate unit, mounting screw, wire connector, photocell, outlet box house grounding wire, headless screw, green grounding screw, backplate, rubber pad, bolt nut, glass shade, frame, and socket ring. It requires a maximum 60W Type ST bulb (not included) for illumination. The fixture is compatible with a dimmer switch when the photocell is disconnected.

Product Usage Instructions

1. Before installation, turn off the main power at the circuit breaker and consult local electrical codes for wiring and grounding requirements.
2. Unscrew the two bolt nuts (D) and remove the two rubber pads (E) and the mounting plate unit (A) from the backplate.
3. Attach the mounting plate unit (A) to the outlet box using two mounting screws (B). Adjust the length of the preinstalled headless screws if necessary. Ensure that two headless screws are lined up horizontally to make the fixture level.
4. Attach the glass shade to the fixture and secure them with the socket ring.
5. Install the bulb (not included). Refer to the relamping label at the socket area or packaging for the maximum wattage allowed.
6. Attach the frame to the fixture using the rubber pad-a and set screw on the top.
7. Attach the backplate of the fixture to the mounting plate unit (A) by aligning and inserting the two headless screws into set holes on backplate. Secure it with two rubber pads (E) and two bolt nuts (D). Use silicone caulking compound to caulk completely around where the backplate meets the wall surface to prevent water from seeping into the outlet box.
8. Turn on the power at the fuse or circuit box.
9. To disconnect the Dusk-to-Dawn Photocell, turn off the power at the fuse or circuit box before starting installation.
10. Loosen the wire connector connected to the wires from the photocell. Do not remove the photocell to prevent water from seeping into the outlet box.
11. Take a white pigtail and black pigtail and make wire connections using wire connector (C). The black wire from the fixture should be connected to one end of the black pigtail, and the white wire from the fixture should be connected to one end of the white pigtail. The other end of the black pigtail should be connected to the black wire from the power source, and the other end of the white pigtail should be connected to the white wire from the power source. Put all wires back into the backplate of the fixture.
12. Turn on the power at the fuse or circuit box.

ASSEMBLY AND INSTALLATION INSTRUCTIONS

WARNING : Turn off the main power at circuit breaker before installing fixture.
NOTE :

1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.

Hardware Package (included)

Installation Steps

Turn off the power at fuse or circuit box.

1. Unscrew the two bolt nuts (D) remove the two rubber pads (E) and the mounting plate unit (A) from the backplate.
2. Attach the mounting plate unit (A) to the outlet box by using two mounting screws (B). Adjust the length of the preinstalled headless screws if necessary. Note: Make sure that two headless screws are lined up horizontally to make the fixture level.
3. Attach the glass shade to the fixture and secure them with the socket ring.
4. Install the bulb (not included). See relamping label at socket area or packaging for maximum wattage allowed.
5. Attach the frame to the fixture by using the rubber pad-a and the set screw on the top.
6. Pull out the source wires from the outlet box. Make wire connections using wire connectors (C) as follows:
   • Connect the hot wire (usually black insulation) from the fixture to the black wire from the power source.
   • Connect the neutral wire (usually white insulation) from the fixture to the white wire from the power source.
   • Attach the fixture grounding wire (usually green with the insulation or bare wire) to the mounting plate unit (A) with green grounding screw. Then, depending on local code, connect it to the house grounding wire with the wire connector (C). Carefully put all of the wires back into the outlet box.
7. Attach the backplate of the fixture to the mounting plate unit (A) by aligning and inserting the two headless screws into set holes on backplate, then secure it with two rubber pads (E) and two bolt nuts (D). Note: With silicone caulking compound, caulk completely around where the backplate meets with the wall surface to prevent water from seeping into the outlet box.

Turn on the power at fuse or circuit box.

Optional Installation: Disconnect Dusk-to-Dawn Photocell

IMPORTANT : Compatible with dimmer when photocell is disconnected. * Requires dimmable bulb and compatible dimmer switch.

1. Turn off the power at the fuse or circuit box before starting installation.
2. Loosen the wire connector connected with the wires from photocell. (See Fig.1) Note: Do not remove the photocell to prevent water from seeping into the outlet box.
3. Take a white pigtail and black pigtail and make wire connections using wire connector (C): (See Fig.2)
   • The black wire from the fixture to one end of the black pigtail.
   • The white wire from the fixture to one end of the white pigtail.
   • The other end of the black pigtail to the black wire from the power source.
   • The other end of the white pigtail to the white wire from the power source. Put all wires back into the backplate of the fixture.

Turn on the power at fuse or circuit box.
The following parts are available for re-order if damaged or missing.

Spare Parts List

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>