VAXCEL T0633 Outdoor Wall Lantern with Clear Glass Installation Guide

T0633 Outdoor Wall Lantern with Clear Glass

Product Information

The T0633/T0634 is a fixture that comes with a photocell function to enable automatic turning on at dusk and off at dawn. The package includes a mounting plate unit, mounting screw, wire connector, photocell, bolt nut, rubber pad, fixture, rubber pad, outlet box house grounding wire, headless screw, green grounding screw, mounting plate unit, fixture grounding wire, fixture wire backplate, set screw, frame, glass shade clip, and can accommodate a maximum of 60W Type A bulb (not included).

Product Usage Instructions

1. Before installation, consult local electrical codes for wiring and grounding requirements.

2. Turn off the main power at the circuit breaker before installing the fixture.

3. Unscrew the two bolt nuts (D), remove the two rubber pads (E), and the mounting plate unit (A) from the backplate.

4. Attach the mounting plate unit (A) to the outlet box by using two mounting screws (B). Adjust the length of the preinstalled headless screws if necessary. Ensure that two headless screws are lined up horizontally to make the fixture level.

5. Gently place the glass shade into the metal frame, then secure it by pressing the clips from the top side.

6. Attach the metal frame to the fixture by aligning the hole and then secure it with the two set screws.

7. Install the bulb (not included). See relamping label at socket area or packaging for maximum wattage allowed.

8. Attach the backplate of the fixture to the mounting plate unit (A) by aligning and inserting the two headless screws into setholes on backplate, then secure it with two rubber pads (E) and two bolt nuts (D). With silicone caulking compound, caulk completely around where the backplate meets with the  wall surface to prevent water from seeping into the outlet box.

9. Turn on the power at fuse or circuit box.

10. To disconnect the Dusk-to-Dawn Photocell: Turn off the power at the fuse or circuit box before starting installation. Loosen the wire connector connected with the wires from photocell (See Fig.1).
    Note: Do not remove the photocell to prevent water from seeping into the outlet box.

11. Take a white pigtail and black pigtail and make wire connections using wire connector (C): (See Fig.2)

    • The black wire from the fixture to one end of the black pigtail.
    • The white wire from the fixture to one end of the white pigtail.
    • The other end of the black pigtail to the black wire from the power source.
    • The other end of the white pigtail to the white wire from the power source. Put all wires back into the backplate of the fixture.

ASSEMBLY AND INSTALLATION INSTRUCTIONS

T0633 / T0634
WARNING : Turn off the main power at circuit breaker before installing fixture.

NOTE:

1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. READ AND SAVE THESE INSTRUCTIONS.

Hardware Package (included):

Installation Steps

Turn off the power at fuse or circuit box.

1. Unscrew the two bolt nuts (D), remove the two rubber pads (E) and the mounting plate unit (A) from the backplate.

2. Attach the mounting plate unit (A) to the outlet box by using two mounting screws (B). Adjust the length of the preinstalled headless screws if necessary.
   Note: Make sure that two headless screws are lined up horizontally to make the fixture level.

3. Gently place the glass shade into the metal frame, then secure it by pressing the clips from top side.

4. Attach the metal frame to the fixture by aligning hole, then secure it with the two set screws.

5. Install the bulb (not included). See relamping label at socket area or packaging for maximum wattage allowed.

6. Pull out the source wires from the outlet box.
   Make wire connections using wire connectors (C) as follows:

   • Connect the hot wire (usually black insulation) from the fixture to the black wire from the power source.
   • Connect the neutral wire (usually white insulation) from the fixture to the white wire from the power source.
   • Attach the fixture grounding wire (usually green with the insulation or bare wire) to the mounting plate unit (A) with green grounding screw. Then, depending on local code, connect it to the house grounding wire with the wire connector (C).
     Carefully put all of the wires back into the outlet box.

7. Attach the backplate of the fixture to the mounting plate unit (A) by aligning and inserting the two headless screws into set holes on backplate, then secure it with two rubber pads (E) and two bolt nuts (D).
   Note: With silicone caulking compound, caulk completely around where the backplate meets with the wall surface to prevent water from seeping into the outlet box.

Turn on the power at fuse or circuit box.

Optional Installation: Disconnect Dusk-to-Dawn Photocell

IMPORTANT:
Compatible with dimmer when photocell is disconnected.

• Requires dimmable bulb and compatible dimmer switch.

1. Turn off the power at the fuse or circuit box before starting installation.

2. Loosen the wire connector connected with the wires from photocell. (See Fig.1)
   Note: Do not remove the photocell to prevent water from seeping into the outlet box.

3. Take a white pigtail and black pigtail and make wire connections using wire connector (C): (See Fig.2)

   • The black wire from the fixture to one end of the black pigtail.
   • The white wire from the fixture to one end of the white pigtail.
   • The other end of the black pigtail to the black wire from the power source.
   • The other end of the white pigtail to the white wire from the power source.
     Put all wires back into the backplate of the fixture.

Turn on the power at fuse or circuit box.

The following parts are available for re-order if damaged or missing.

Spare Parts List:

Documents / Resources

| VAXCEL T0633 Outdoor Wall Lantern with Clear Glass [pdf] Installation Guide
T0633, T0634, T0633 Outdoor Wall Lantern with Clear Glass, Outdoor Wall Lantern with Clear Glass, Wall Lantern with Clear Glass
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>