WRC SBXE.2 1/8 Competition Electric Off Road Buggy Instruction Manual

October 30, 2023
WRC

WRC SBXE.2 logo1

new generation rc car

1/8 OFF-ROAD 4WD ELECTRIC

RC PROFESSIONAL BUGGY

WRC SBXE.2 18 Competition Electric Off Road Buggy

INSTRUCTION MANUAL

www.wrc-racing.com

WRC SBXE logo1

NOTE:







INTRODUCTION

SBXE is a new generation high quality 1/8 scale electric off-road buggy.
SBXE is supplied in a box, you can download the Instruction manual from www .wrc-racing.com
Its use is intended for more than 16 years old persons with experience on rc model car field.
Children and all the persons without this requirement MUST have direct supervision of a knowledgeable adult responsible.

SAFETY PRECAUTIONS

Instruction Manual MUST be read and fully understood before to start building and operating functions.
Always keep Instruction Manual in safety place, ready to be consulted for any reference you need.
Use only original WRC spare parts.

GENERAL INFORMATION

Assemble the kit only away from the reach of children.
Follow the building and operating instructions using the utmost care.
Don’t put any part of your body inside rotating and moving elements as this may cause damage or serious injury.
Check and clean the model before putting it away.
Don’t use your model car in public places or in roads and areas where it could generate conflict with person or vehicular traffic.
The model car is controlled by radio: you MUST put great care to avoid loss of radio control always keeping a safety margin all around your model in order to prevent any collision.
Operating frequency: check and be sure it is clear and not shared with anybody at same time; it could cause loss of control of the RC model.
Always turn on your transmitter before you turn on the receiver in the car and always turn off the receiver before you turn off your transmitter.
Keep the wheels of the model off the ground when checking the operation of the radio equipment.
Disconnect the battery pack before storing your model.

WARRANTY

WRC guarantees this model kit to be free from defects in both material and workmanship within 30 days of purchase.
The total monetary value under warranty will in no case exceed the cost of the original kit purchased.
This warranty doesn’t cover any components damaged by use or modification or as result of wear.
Part or parts missing from this kit must be reported within 30 days of purchase.
No part or parts will be sent under warranty without proof of purchase.
If you find a defective or missing part, contact the local distributor.
Customer service and support will be provided through local hobby store.
No warranties are expressed or implied that cover damage caused by what is considered normal use or cover or imply how long any model cars’ components or electric components will last before requiring replacement.
Due to the high performance level of this model car you will need to periodically maintain and replace consumable components; any and all warranty coverage will not cover replacement of any part or component damaged by neglect, abuse or improper or unreasonable use.
This includes but is not limited to damage from crashing, excessive moisture, improper use or no maintenance or user modifications which compromise the integrity of components.
Warranty will not cover components that are considered consumable on RC model car.
WRC doesn’t pay nor refund on any component sent from WRC or its distributor for warranty.
WRC reserves the right to make final determination of the warranty status of any component or part
Use only original WRC spare part:

CUSTOMER SUPPORT

Please don’t hesitate to contact WRC support at info@wrc-racing.com for any problem or question.
Also kindly visit our website www.wrc-racing.com to find last updates, set-up information, option parts and other information.

W.R.C. world racing car s.r.l.
Via Meucci, 23/B
36040 Brendola (VI)
ITALY

Phone: 0039 0 444 401138
fax: 0039 0 444 401139
E-mail: info@wrc-racing.com
Website: www.wrc-racing.com

TECHNICAL INFORMATION

– WHEELS LOCK: Lightweight 17 mm 7075 T6 Nut
– CHASSIS: 3.0 mm Swiss 7075 T6 aluminium
– RADIO PLATE: Composite Material
– DRIVETRAIN TYPE: Spring steel CVD Driveshfts
– FRONT DIFFERENTIAL: Differential Gear
– REAR DIFFERENTIAL: Differential Gear
– SUSPENSION: Pivot ball suspension
– RIDE HEIGHT: Adjustable Front & Rear
– CAMBER: Adjustable Front & Rear
– CASTER: Adjustable Front
– TOE: Adjustable Front & Rear
– ROLLCENTER: Adjustable Front & Rear
– ACKERMANN: Adjustable Front
– ANTI-ROLL BARS: Adjustable Front & Rear

TECHNICAL DATA

– WIDTH ……………………………………… 310 mm
– WHEEL BASE ………… adjustable 315-320 mm.

ADDITIONAL ITEMS NEEDED FOR COMPLETION (REQUIRED BUT NOT INCLUDED IN THE KIT)

             WRC SBXE.2 18 - Parts 2

ENGINE AND MUFFLER    TRANSMITTER        RECEIVER

WRC SBXE.2 18 - Parts 4

LOW PROFILE STEERING SERVO    BATTERIES FOR TRANSMITTER AND RECEIVER

WHEEL – TYRES – INSERTS

2 X 7.4 V                                       1 X 14.8 V

LIPO BATTERIES

TOOLS REQUIRED

THESE TOOLS ARE NOT INCLUDED IN THE KIT BUT ARE REQUIRED FOR PROPER ASSEMBLY

ALLENS:                                      SOCKET
1.5 mm                                           5mm
2 mm
2.5 mm
3 mm

SIDE CUTTERS                                  COMBINATION PLIERS

TOOL FOR TURNBUCKLES/NUTS     WHEEL NUT TOOL 17mm

GREASE                                 OILS: 5000 CST BEARING OIL

NOTICE:

THE FOLLOWING ITEMS ARE NEEDED FOR COMPLETION OF THE SBXE; THEY ARE NOT INCLUDED IN THIS KIT (UNLESS NOTED) AND SHOULD BE OBTEINED FROM YOUR LOCAL HOBBY SHOP.
BE SURE TO READ THE INSTRUCTION COMPLETELY PRIOR TO ASSEMBLY

BAG 1
Central Diff. Gear

WRC SBXE.2 18 - Bag 1a

  1. DIFFERENTIAL OIL :
    Central : 5000 cst
    Weight : 3 g

  2. Fill the differential up to the top of the pin.
    DO NOT fill the diff. to the top of the housing.

BAG 2
Front Diff. Gear

WRC SBXE.2 18 - Bag 2a

  1. DIFFERENTIAL OIL :
    Front : 5000 cst
    Weight : 3 g

  2. Fill the differential up to the top of the pin.
    DO NOT fill the diff. to the top of the housing.

BAG 3
Rear Diff. Gear

WRC SBXE.2 18 - Bag 3a

  1. DIFFERENTIAL OIL :
    Rear : 5000 cst
    Weight : 3 g

  2. Fill the differential up to the top of the pin.
    DO NOT fill the diff. to the top of the housing.

BAG 4
Rear Transmission

WRC SBXE.2 18 - Bag 4

BAG 5
Front Transmission

WRC SBXE.2 18 - Bag 5

BAG 6
Front Suspension

WRC SBXE.2 18 - Bag 6a

  1. Lower Arm Position
  2. ADJUST THE PLAY WITH THE SHIMS

SCREW POSITION

WRC SBXE.2 18 - Bag 6c

BAG 7

WRC SBXE.2 18 - Bag 7a

WRC SBXE.2 18 - Bag 7b

  1. Upper Arm Position
BAG 8
Front Upright

WRC SBXE.2 18 - Bag 8a

WRC SBXE.2 18 - Bag 8b

WRC SBXE.2 18 - Bag 8c

BAG 9
Rear Suspension

WRC SBXE.2 18 - Bag 9a

WRC SBXE.2 18 - Bag 9b

WRC SBXE.2 18 - Bag 9c

  1. Lower Arm Position
  2. ADJUST THE PLAY WITH THE SHIMS
  3. Optional
    Bearing Mounted Anti roll-bar Kit
    Front – Rear
BAG 10

WRC SBXE.2 18 - Bag 10a

WRC SBXE.2 18 - Bag 10b

WRC SBXE.2 18 - Bag 10c

BAG 11

WRC SBXE.2 18 - Bag 11a

WRC SBXE.2 18 - Bag 11b

  1. High Position
  2. Low Position
BAG 12
Front & Rear Assembly

WRC SBXE.2 18 - Bag 12

BAG 13

WRC SBXE.2 18 - Bag 13a

WRC SBXE.2 18 - Bag 13b

BAG 14

WRC SBXE.2 18 - Bag 14a

WRC SBXE.2 18 - Bag 14b

Electric motor

WRC SBXE.2 18 - Bag 14c

PINION GEAR

RCM10-12     12 T
RCM10-13     13 T
RCM10-14     14 T
RCM10-15     15 T
RCM10-16     16 T
RCM10-17     17 T
RCM10-18     18 T

WRC SBXE.2 18 - Bag 14d

BAG 15
Electric Battery

WRC SBXE.2 18 - Bag 15a

WRC SBXE.2 18 - Bag 15b

  1. BATTERY
    NOT INCLUDED

  2. VELCRO STRAP

  3. BATTERY FOAM PAD
    Install the pad between battery and the battery tray

  4. Two Lipo Batteries
    Version

Radio Case

WRC SBXE.2 18 - Bag 15c

WRC SBXE.2 18 - Bag 15d

BAG 16
Front Shock

WRC SBXE.2 18 - Bag 16a


Assembly 2 set

WRC SBXE.2 18 - Bag 16b

a) DO NOT BLOCK COMPLETELY ALLOW THE PISTON TO ROTATE

SHOCK FILLING

Fully extend the piston rod so the piston is at the bottom of the shock body.

Hold the shock upright and fill the shock body with shock oil as in the picture.

Let the oil settle and allow air bubbles to rise to the top.
Slowly move the piston up and down until no more air bubbles appear.
Add shock oil as necessary.

Pull the piston rod most of the way out of the shock bod.
Let the shock rest for 5 minutes to allow the air bubbles to scape.

SPRINGS


COD

| FORCE|

COLOUR

100125
100125-2
100125-3|

MEDIUM
SOFT
HARD

|

BLACK
YELLOW
RED

P- ONE SHOCKS OIL

CODE|

CST

SO-400
SO-500
SO-600
SO-700
SO-800|

400
500
600 (IN KIT)
700
800

Set distance

WRC SBXE.2 18 - Bag 16e


WRC SBXE.2 18 - Bag 16f

BAG 17
Rear Shock

WRC SBXE.2 18 - Bag 17a


Assembly 2 set

WRC SBXE.2 18 - Bag 17b

a) DO NOT BLOCK COMPLETELY ALLOW THE PISTON TO ROTATE

SHOCK FILLING

Fully extend the piston rod so the piston is at the bottom of the shock body.

Hold the shock upright and fill the shock body with shock oil as in the picture.

Let the oil settle and allow air bubbles to rise to the top.
Slowly move the piston up and down until no more air bubbles appear.
Add shock oil as necessary.

Pull the piston rod most of the way out of the shock bod.
Let the shock rest for 5 minutes to allow the air bubbles to scape.

SPRINGS


COD

| FORCE|

COLOUR

100126
100126-2
100126-3|

MEDIUM
SOFT
HARD

|

BLACK
YELLOW
RED

P- ONE SHOCKS OIL

CODE|

CST

SO-400
SO-500
SO-600
SO-700
SO-800|

400
500
600 (IN KIT)
700
800

Set distance

WRC SBXE.2 18 - Bag 17d


WRC SBXE.2 18 - Bag 17e

BAG 18
Rear Wing

WRC SBXE.2 18 - Bag 18a

Tyres – Body

WRC SBXE.2 18 - Bag 18b

  1. To mount the optional body nose (100316-4) please make a Ø2,5 hole where indicated above and cut away the standard body nose.

WRC SBXE logo1| Driver:| Track:
---|---|---
Date:| Event:
Front Suspension:
Ride Height:| WRC SBXE.2 18 Competition Electric Off Road Buggy
-a3

  1. Caster Shim:
  2. Upper Ball Type:
  3. Caster Shim:
  4. Upper Ball Shim:
  5. Washer:
  6. Lower Ball Shim:
  7. Whellbase Shim:
  8. Lower Ball Type:
  9. Lower Arm Position
  10. Upper Arm Position

Camber:
Toe:
Anti-Roll Bar| **
Size:
Gap:
Ackerman| **
Drive Shaft:
Chassis Brace:
Hex:
Rear Suspension:
Ride Height:| WRC SBXE.2 18 Competition Electric Off Road Buggy -
a5

  1. Hub Shim:
  2. Shim:
  3. Lower Arm Position

Camber:
Toe:
Anti-Roll Bar| **
Size:
Gap:
Drive Shaft:
Chassis Brace:
Hex:
Shocks:
**
|

Front

|

Rear

| WRC SBXE.2 18 Competition Electric Off Road Buggy -
a6

  1. Free Length
  2. Rebound

Piston:| |
Membrane:| |
Oil:| |
Spring:| |
Rebound:| |
Free Length:| |
Differential:
****|

Front

| Center|

Rear

Case Mat.:| | | **
Oil:| **| |
Crown Gear:| | | **
Gearing :
Clutch Belt:| **| ****|

Spur Gear

Shoe:| | |

Spring

Tires:
****|

Front

|

Rear

Brand:| |
Pattern:| |
Insert:| |
Whells:| |
Compound:
Total Vehicle Weight:
Tracks:
Size:| **
Traction:| **
Surface:| **
Type:| **
Condition:| **
Temperature:| **
|
Body, Wing:
Body:| **
Wing:| **
Wing Height:| **
Gap to tower:| **
|
|
|
Electronics:
Radio:| **
Servo:| **
Epa:| Throttle:           %  Brake:             %
Expo:| Throttle:           %  Brake:             %
Esc:| **
Motor:| **
Battery| ****

WRC SBXE logo1

WRC SBXE.2 18 Competition Electric Off Road Buggy 1


W.R.C. world racing car s.r.l.

www.wrc-racing.com

Documents / Resources

| WRC SBXE.2 1/8 Competition Electric Off Road Buggy [pdf] Instruction Manual
SBXE.2 1 8 Competition Electric Off Road Buggy, SBXE.2, 1 8 Competition Electric Off Road Buggy, Competition Electric Off Road Buggy, Electric Off Road Buggy, Off Road Buggy, Road Buggy
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals