VEVOR LSST-515 Pottery Wheel Machine User Manual

VEVOR LSST-515 Pottery Wheel Machine

Product Information

The VEVOR Pottery Wheel Machine is a household electrical equipment that can be used for pottery making. It has a maximum payload capacity of 5 KG and operates on a voltage range of 100-240V 50/60Hz. The machine has a power of 350W and a rated current of 32A. It operates at a speed range of 0-300r/min and has a sound power level of 60dB. The machine comes with tool accessories including an apron, an 8-piece toolset that includes a clay cutting line, a small yellow sponge, a wooden knife, and a wooden scraper.

Product Usage Instructions

1. Read all safety warnings, instructions, illustrations, and specifications provided with the electrical equipment before use.
2. Ensure that the pottery wheel machine is placed on a flat surface before use.
3. Plug the power line into a power source that matches the voltage and frequency requirements of the machine.
4. Turn on the power light by pressing button 8 on the structure diagram.
5. Adjust the speed of the wheel using the speed-regulating pedal (5).
6. Use the tool accessories provided to shape and mold the clay into desired shapes. The apron provided should be worn to prevent clothes from getting dirty.
7. During use, periodically check whether the power cable is damaged and the connector is loose. If there are any damages or loose connections, stop using the machine immediately and contact customer service for technical support.
8. When cleaning and maintaining the machine, ensure that children are not around to avoid accidents. Cleaning and user maintenance shall not be made by children without supervision.

Please note that the appearance of the product may vary from the user manual as it is subject to the product you received. If there are any technology or software updates on the product, VEVOR will not inform you again. For any product questions or technical support, please contact CustomerService@vevor.com.

We continue to be committed to offering tools at competitive prices. “Save Half”, “Half Price”, or any other similar expressions used by us only represent an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and do not necessarily mean to cover all categories of tools offered by us. You are kindly reminded to verify carefully when placing an order with us if you are saving half in comparison with the top major brands.

NEED HELP? CONTACT US!

Have product questions?
Need technical support? Please feel free to contact us: CustomerService@vevor.com.

This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product.

SAFETY INSTRUCTIONS

WARNING:
Read all safety warnings, instructions, illustrations, and specifications provided with this electrical equipment. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

• Warning – To reduce the risk of injury, the user must read the instructions manual carefully.
• Alternating current
• This symbol, placed before a safety comment, indicates a kind of precaution, warning, or danger. Ignoring this warning may lead to an accident. To reduce the risk of injury, fire, or electrocution, please always follow the recommendation shown below.
• HOUSEHOLD USE ONLY

1. This equipment is only applicable to ceramic drawings and cannot be used for other purposes. Do not use the equipment brutally.
2. The equipment shall be placed on a cool, ventilated, dry, dust-proof and level ground.
3. Users must wire and install according to electricity safety standards.
4. Do not change the rotation direction when the motor is running. To change the rotation direction, stop it first, and start it after the motor completely stops rotating.
5. Please use a towel or sponge to clean the machine body, and do not use a lot of water to wash it to avoid water immersion in the motor, switch, bearing, and other parts, causing failure.
6. Before use, make sure that the switch and pedal are in the stop position before inserting the power.
7. When repairing or replacing parts, the switch must be cut off and the power supply must be unplugged.
8. Children should use this equipment with adults(Note: This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision).
9. Periodically check whether the power cable is damaged and the connector is loose.
10. Press button(10A) on the leakage protector once a month to check whether the leakage protection can work normally!

MODEL AND PARAMETERS

STRUCTURE DIAGRAM

1. Removable water basin
2. Aluminum turntable
3. Equipment body
4. Manual adjusting lever
5. Speed regulating pedal
6. Foot Pad
7. Forward/reverse switch
8. Power light
9. Leakage protector
10. Power line
    • 10A.Leakage protection test switch

TOOL ACCESSORIES AND USE

1. Apron(x1): Prevent clothes from getting dirty.
2. 8-Piece Tool Set(x1)
   • A (Clay cutting line): Assist in precisely cutting clay (cutting surface is very smooth)/repairing and leveling the mouth of the work/taking away the finished product.
   • B (Small yellow sponge): Add water or absorb water/trim the surface or mouth edge to make it smooth.
   • C (Wooden knife): Trim the bottom for later removal/trimming.
   • D (Wooden scraper): Trim the opening/shape and remove the excess clay on the surface to make it smooth.
   • E (Stainless steel scraper): Remove the excess clay on the surface to make it smooth.
   • F (Circular large flat wire knife): Trim the surface of the vessel/ control the thickness/trim out the bottom ring foot.
   • G (Steel needle): Scrape off excess clay from the mouth edge/remove air bubbles/punch holes.
   • H (Ribbon flat wire knife): Finely trim the surface of the utensil or circle the foot.
3. Stainless steel clay-repair knife 8-piece Set(x1): Repair clay molds as shown below.
4. Aluminum turntable（Φ280mm): The size of the turntable depends directly on the maximum diameter we can achieve. (Loosen the bolt with a wrench and replace it)

OPERATING STEPS

• Step 1: Take out a proper amount of clay, throw the mud ball in the center of the wheel, and press it (wet your hands).
• Step 2: Plug in the power (If the water basin is not installed, install the water basin first).
• Step 3: Turn on the leakage protection switch upward and choose the direction of forward (clockwise)/reverse (counterclockwise) rotation according to your needs.
• Step 4: Push the lever/pedal to adjust the speed and start clay molding with tools.
• Step 5: Clay-mold repairs with tools.
• Step 6: Creative painting and coloring can be carried out according to their own needs. After the work is completed,stop the machine in reverse order.

Remove the molding with a scraper/clay cutting line. Place in a cool place for a period of time before firing.

SKILLS GUIDANCES

lifting

| The lifting process should

be small and even.

Clay is in a spiral shape.| The clay molding speed exceeds the machine

speed.

| Turn the mold a few times in advance.
Clay unevenly stressed presses| Abnormal posture of clay molding.| Sit firmly and keep your back, neck, shoulders, upper arms, forearms, wrists and palms still. Coordinate your whole body

Strength.

Clay off center| Got wrong and unstable force on hands when looking for the center.| The left palm must be placed in the eight o ‘clock position on the turntable and

applied downward oblique

2. Not opening in the center. 3.Hands shake when pressing down, uneven

force.

| The opening of the middle tip of the left finger or thumb must be assisted by the right finger and must be pressed down vertically

from the center point.

Hollow at the bottom| Pressing down too fast and too hard.| 1. The bottom thickness of the hole should be left about 2cm.

2. Pause the machine, add new clay, start the machine,

and smooth the surface.

Bubbles.| The clay has not been kneaded properly.| Pause the machine and prick the air bubbles with a needle, fill the hole with clay, then start the machine

to smooth the surface.

Uneven thickness when lifted.| Hands are not on parallel lines or uneven force.| The inner and outer fingertips must move synchronously in a straight

line when lifting the clay.

Mold collapsed.| 1. There was too much water and the clay was too soft to hold.

2. Opening rapidly expands, deformation and collapse. 3.The wall is thick on the top and thin on the bottom, which cannot be supported. 4.Clay is used for too long

and its viscosity decreases.

| 1.  Use as little water as possible when drawing.

2.  Keep your hands moving from the bottom to the top.

3.  Never press down.

4.  Rapid prototyping.

TROUBLESHOOTING INSTRUCTION

power plug is properly inserted.

2. Check whether the

leakage protector is on.

Shaking of the machine| The machine is not level with the ground.| Adjust the four feet of the machine so that the machine is level with the

ground.

The turntable makes a

sound.

| The water basin against the

turntable.

| Check whether water basin

is properly installed.

Water basin is leaking.| 1. The water exceeds the waterproofing edge of the basin.

2. The water basin is not installed properly.

| 1. Check whether the storage of mud water exceeds the waterproof edge.

2. Check that water basin is

properly installed.

The turntable jumps too much.| The fastener is loose.| Check whether the fastener is loose. If not, ask a professional to debug it.

CLEAN AND CARE RULES

1. After finishing the equipment operation, it is necessary to clean the clay on the surface of the turntable and wipe the water stains on the surface of the turntable (Do not rinse directly with water).
2. Check the parts regularly for looseness.
3. If you use it sparingly, run it at least once a month.

Manufacturer:
Hebei Lesheng Teaching Equipment Co., Ltd.

ADD:
East of Xingye Street, North of Hai’an Road, Haixing County, Cangzhou City, Hebei Province

Importer:
WAITCHX

Address:
250 bis boulevard Saint-Germain 75007 Paris

Made in China.

Support and E-Warranty Certificate https://www.vevor.com/support.

References

• Contact Us – Official VEVOR Support

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>