VEVOR 4X3X2.75 Inflatable Paint Booth User Manual
- October 30, 2023
- VEVOR
Table of Contents
Technical Support and E-Warranty Certificate
www.vevor.com/support SPRAY PAINT BOOTH
USER MANUAL
MODEL:4X3X2.75 / 6X3X2.5 / 7X4X2.75 8X4.5X3.3 / 8.5X4.8X3.3 / 10X6X4
4X3X2.75 Inflatable Paint Booth
We continue to be committed to offering tools at competitive prices. “Save
Half”, “Half Price”, or any other similar expressions used by us only
represent an estimate of savings you might benefit from buying certain tools
with us compared to the major top brands and do not necessarily mean to cover
all categories of tools offered by us. You are kindly reminded to verify
carefully when placing an order with us if you are saving half in comparison
with the top major brands.
NEED HELP? CONTACT US!
Have product questions? Need technical support? Please feel free to contact
us:
****CustomerService@vevor.com
This is the original instruction, please read all manual instructions
carefully before operating. VEVOR reserves a clear interpretation of our user
manual. The appearance of the product shall be subject to the product you
received. Please forgive us that we won’t inform you again if there are any
technology or software updates on our product.
Safe Instructions
WARNING:
- Avoid using this product in rain, strong wind, hail, and other bad weather.
- Avoid sharp points, blades, and other items to scratch the product.
- Keep away from fire sources.
- The air inside the tent is scarce, so good ventilation must be ensured when painting inside the tent.
- Due to the large size of this product, installation requires 2 to 4 people to assist.
CAUTION: Carefully read instructions and procedures for safe operations.
PRODUCT INTRODUCTION
Model
SPEC.| 4X3X2.75| 6X3X2.5| 7X4X2.75| 8X4.5X3.3| 8.5X4.8X3.3| 10X6X4
---|---|---|---|---|---|---
Size| 13’10’9ft| 20’10’8ft| 23’13’8.5ft| 26’15411ft| 28’16’11ft| 33’20’13ft
Material| 210D Oxford- fabric| 210D Oxford-
fabric| 210D Oxford-
fabric| 210D Oxford-
fabric| 210D Oxford-
fabric| 210D Oxford-
fabric
Color| Blue| Blue| Blue| Blue| Blue| Blue
Input voltage| 120V- 60Hz(USA) 220-240V- 50Hz(EUR/ AUS)| 120V- 60Hz(USA)
220-240V- 501-1z(EUR/ AUS)| 120V– 60Hz(USA) 220-240V- 50Hz(EUR/ AUS)| 120V-
60Hz(USA) 220-240V- 50Hz(EUR/ AUS)| 120V- 60Hz(USA) 220-240V- 50Hz(EUR/ AUS)|
120V60Hz(USA) 220-240V-50Hz(EUR/ AUS)
Inflation blower power| 950W| 750W| 750W| 950W| 950W| 1100W
Ventilation blower power| /| 480W (USA)| 480W (USA)| 750W
(USA)| 750W
(USA)| 950W
(USA)
/| 550W(EUR /AUS)| 550W(EUR /AUS)| 750W(EUR /AUS)| 750W(EUR /AUS)| 950W(EUR
/AUS)
G.W| 25.4kg| 36.2kg| 44.4kg| 56kg| 57.4kg| 74.6kg
N.W| 21.6kg| 31kg| 39kg| 50kg| 51.2kg| 67.6kg
PACKAGE CONTENT
model Parts | 4X3X2.75 | 6X3X2.5 | 7X4X2.75 | 8X4.5X3.3 | 8.5X4.8X3.3 | 10X6X4 |
---|---|---|---|---|---|---|
Spray paint booth | x1 | xl | xl | xl | x1 | xl |
inflation blower | xi | x 1 | xl | xi | x1 | xi |
Ventilation blower | / | xl | x1 | xl | x1 | xl |
Storage bag | x1 | xl | xl | xl | x1 | xl |
Sand bags | x4 | I | x4 | 7 | x4 | x6 |
Stakes | x4 | x4 | 7 | 7 | x4 | x6 |
Ropes | x4 | x4 | x4 | x4 | x4 | x6 |
Pack of repair patches | x1 | xi | xi | xi | x i | xi |
PRODUCT DIAGRAM
1. Front Door
2. Air Column
3. Light Hook
4. Ceiling
5. Rope Ring
6. Activated Carbon Filter Cotton
7. Handle
8. Ventilating Tube| 9. Air Column Filling Tube
10.Air Blower
11. Transparent Window
12. Emergency Escape Window
13. Double Filter Cotton
14. Exhaust Zipper Port
15. Bottom
16. Metal Ring
17. Power Line Inlet
---|---
INSTALLATION INSTRUCTION
- Unfold the tent and spread it out on a clean and level ground.
- Zip up both sides of the product.
- Tie the rope to the rope ring.
- Tie the air tube to the air blower outlet, as shown in the figure. 1 is the ventilation blower; 2 is the inflation blower.
- When the tent is inflated, please fasten the tent with stakes at the bottom metal rings.
- When the assembly is complete, please tie the windproof rope to the fixed object.
Storage Instruction
It is recommended to store the product when it is dry to avoid dampness and
mildew.
It is recommended to put them in a storage bag and store them in a dry
environment.
Keep away from sharp objects to avoiding scratching.
After wet weather, it is recommended to air the tent on sunny days.
-
Unzip and open the front and back doors.
-
Turn off the air blowers and open both exhaust zipper ports.
-
Drain all air and flatten the tent as shown below.
-
Roll up the tent, as shown in the figure
-
Roll up the tent with ropes.
-
Put it into a storage bag and place in dry environment.
Direction for Use
- This product is only a simple tool room for painting and can not be used in windy and rainy days.
- The product requires the blower to keep inflating , and do not to cut off the power supply.
- In case of power failure, please escape through the front door or safety window or back door.
- In case of emergency, you can cut through the tent with a knife to escape.
- It is recommended to choose a flat and clean open ground to use this product.
- If the tent shakes too much in the wind, please use the windproof ropes and stakes to fix the tent.
- After repeated use, the ventilation of the tent may become poor. At this time, the inner blue filter cotton can be removed or replaced to improve the ventilation.
- If it is difficult to inflate the tent, zip up the front and back doors, turn on the Ventilation blower to inflate the tent, and then turn on the Inflation blower to fully inflate the tent.
Maintenance, Repair, and Troubleshooting
- When the product is finished, it is recommended to dry the tent and put it away.
- If the product is stored in a humid environment, it is recommended to take it out to open it in sunny weathers.
- If the product is torn, please repair it with the accompanying material and tools.
Troubleshooting
problem | cause | solution |
---|---|---|
Blower does not work | · Voltage mismatch |
· No power supply
· The blower switch is not on| · Voltage need to match
· Turn the power
· Turn on the blower
Lack of tent pressure| · Voltage instability
· The air tube is connected to a wrong blower
· Both exhaust ports are not zipped properly| · Supply a stable voltage
· Connect the air tube to the inflation blower
· Zip both sides of the exhaust ports
Importer: WAITCHX
Address: 250 bis boulevard Saint-Germain 75007 Paris
Importer: FREE MOOD LTD
Address: 2 Holywell Lane, London, England, EC2A 3ET
EUREP GmbH
Unterlettenweg 1 a, 85051 Ingolstadt, Germany
EUREP UK LTD
UNIT 2264, 100 OCK STREET, ABINGDON
OXFORDSHIRE ENGLAND OX14 5DH
Made in China
Manufacturer: Guangzhou Yijia Inflatable Co., Ltd
Add: No. 1, Lirong Road, Shiling Town, Huadu District, Guangzhou, China
Technical Support and E-Warranty Certificate
www.vevor.com/support
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>