jura E6 Coffee Machines Instruction Manual

: October 30, 2023
: Jura

Table of Contents

IMPORTANT SAFEGUARDS
Control elements
Preparing and using for the first time
Preparation
Daily operation
Machine settings
Maintenance
Display messages
Troubleshooting
Transport and environmentally friendly disposal
Disposal
Technical data
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

jura E6 Coffee Machines Instruction Manual

IMPORTANT SAFEGUARDS

Comply with the Failure to observe the instructions for use may result in serious
instructions for use injuries or damage to property. Safety information is therefore indicated as follows:

This is the safety alert symbol. lt is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.

DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.

WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION , used with the safety alert symbol, indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

NOTICE is used to address practices not related to personal injury

Follow the basic safety When using electrical appliances, basic safety precautions shall
precautions always be followed, to reduce the risk of fire, electric shock, and/or injury to persons, including the following:

Read all instructions.
Do not touch hot surfaces. Use handles or knobs.
To protect against fire, electric shock and injury to persons, do not immerse power cord, plugs, or body of machine in water or other liquid.
Close supervision is necessary when any appliance is used by or near children.
Unplug from outlet when not in use and before cleaning. Allow to cool before putting on or taking off parts, and before cleaning the appliance.
Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, or has been damaged in any manner. Return appliance to the nearest authorized service facility for examination, repair or adjustment.
The use of an accessory attachment not recommended by the appliance manufacturer may result in fire, electric shock, or injury to persons.
Do not use outdoors.
Do not let the cord hang over the edge of a table or counter, or touch hot surfaces.
Do not place on or near a hot gas or electric burner, or in a heated oven.
To disconnect, turn any control to ‘OFF’ then remove plug from wall outlet.
Do not use appliance for other than intended use.
Use extreme caution when dispensing hot steam, hot water or hot coffee.

SAVE THESE INSTRUCTIONS. Pass them on to any subsequent user.

Intended use The appliance is designed and intended for household use only. It shall only be used for coffee preparation and to heat milk and water,according to these instructions. Use for any other purpose will be deemed improper. JURA Elektroapparate AG cannot accept any responsibility for the consequences of improper use.

People, including children, who

do not have the physical, sensory or mental capabilities to use the appliance safely or
are inexperienced or lack knowledge in how to use the appliance safely must be supervised by a responsible person when using it, or must be instructed in how to use it correctly.

Special power cord set instructions

A short power-supply cord is to be provided to reduce risks resulting from becoming entangled in or tripping over a longer cord.
The cord shall be arranged so that it will not drape over the counter top or table top where it can be pulled on by children or tripped over.
This appliance has a 3-pin grounded plug.
Do not modify the plug in any way

Extension cords are available an may be used if care is exercised in their use. If the user chooses to use an extension cord,

the marked electrical rating of the extension cord should be at least as great as the electrical rating of the appliance, and
if the appliance is of the grounded type, the extension cord should be a grounding type 3-wire cord, and
the longer cord should be arranged so that it will not drape over the counter top or tabletop where it can be pulled on by children or tripped over.

WARNING
To reduce the risk of fire or electric shock, DO NOT remove any service covers. DO NOT modify the appliance in any way that is not described in these instructions. NO user serviceable parts included. Repair MUST be done by authorized personnel only. In the event of signs of damage, for example if there is a smell of burning, unplug the machine immediately from outlet and contact JURA customer service.

CAUTION
This appliance is for household use. Any servicing other than cleaning and user maintenance shall be performed by an authorized service representative:

Do not immerse base in water or try to disassemble.
Do not put the appliance or any individual parts in thedishwasher.
Check voltage to be sure that the voltage indicated on the name plate complies with your voltage. The name plate is located on the underside of the appliance.
Never use warm or hot water to fill the water container. Use cold water only.
Keep your hands and the cord away from hot parts of the appliance during operation.

There is a risk of scalds or burns on the spouts and the cappuccino frother / nozzle.

Keep children away.
Do not touch any hot parts. Use the handles or knobsprovided.
Ensure that the cappuccino frother / nozzle is correctly fitted and clean. If incorrectly fitted or if they become blocked, the cappuccino frother or its parts might come off.

NOTICE

Never clean with scouring powders or hard implements.
Ensure that the ventilation slots are not covered.
Never pull out the drip tray during the brewing process. Only pull the drip tray when the display instructs you or when the appliance is ready for use.

NEVER DO (or you will void your warranty protection):

Never fill instant coffee, chocolate mix etc. into the bean container or ground coffee funnel (filler funnel for ground coffee). It will damage the functioning of the brewing chamber.
Never fill sugar coated coffee beans into the bean container. In case of doubt, call your dealer.
Never fill anything other than coffee beans into the bean container (no chocolate, no rice, no nuts, no spices, nothing other than roasted coffee beans).
Never fill frozen beans into the bean container. If you store beans in the freezer, let them thaw 3 to 4 hours before filling them into the bean container.
Never fill anything but fresh, cold and clean water into the water tank, except when decalcifying.
Never use mineral or carbonated water. You can use tap water, bottled water, spring water and reverse osmosis water.
Never do anything with the machine which is not described in these instructions. In case of doubt, call your dealer.

Control elements

On/Off button Q
Display
Multi-function buttons (button function depends on what is shown in the display)
Switch for hot water and milk foam preparation
Height-adjustable coffee spout
Fine foam frother
Cup platform
Insert for drip tray
Drip tray
Coffee grounds container
Power cord (permanently connected or plug-in) (back of the machine)
Water tank
Water tank cover
Bean container with aroma preservation cover
Service socket for optional JURA WiFi Connect
Filler funnel for ground coffee
Filler funnel cover
Grinder adjustment switch
Container for milk system cleaning
Measuring spoon for ground coffee
Hot-water nozzle

Preparing and using for the first time

Setting up the machine
When setting up your E6, please note the following:
Setting

Place the E6 on a horizontal surface that is not sensitive to water.
Choose a spot for your E6 which protects the machine against overheating. Ensure that the ventilation slots are not covered.

Filling the bean container NOTICE
Coffee beans which have been treated with additives (e.g. sugar), ground coffee or freeze-dried coffee will damage the grinder.

Only use roasted, untreated coffee beans to fill the bean container.
Remove the aroma preservation cover.
Remove any dirt or foreign objects from inside the bean container.
Fill the bean container with coffee beans and close the aroma preservation cover.

Determining the water hardness
When you use the machine for the first time, you must set the water hardness. If you do not know the hardness of your water, you can find this out first. Use the Aquadur® test strips supplied with the machine.

Hold the test strip under flowing water for one second. Shake off the water.
Wait for about 1 minute.
You will then be able to read the degree of water hardness from the discoloration of the Aquadur® test strip and the description on the packaging.

Level| Display German Degree (°dH)| Degrees of general hardness (°dGH)| Parts per million (ppm)| Indicator Strip number of ‘reddish’ fields
---|---|---|---|---
Not active| | | |
Very soft water| <3| <3| < 53.4| None
Soft water| >4| >4| >71| 1
Hard water| >8.4| >8.4| >150| 2
Very hard water| >14| >14| >250| 3

First-time use

WARNING

If the machine is operated with a defective power cord, there is a danger of potentially fatal electric shock.

Never use a machine which is damaged.
Never use a machine which has a defective power cord.

NOTICE

Milk, sparkling mineral water or other liquids can damage the water tank or the machine.

Only fill the water tank with fresh, cold water.

The water volume is given as standard in ‘oz’. You can change this setting to ‘ml’ in programming mode (see Chapter 6 ‘Machine settings’)

Precondition: The bean container has been filled.

For machines with a plug-in power cord: Connect the power cord to the machine.
Insert the power plug into a power socket.
Press the On/Off button Q to switch the E6 on.‘Choose language’
Press the 0 or 9 button until the desired language is displayed,e.g. ‘English’.
Press the ‘Save’ button. ‘Saved’ appears briefly on the display. ‘Water hardness’

If you do not know the hardness of your water, you must find this out first (see chapter 3 ‘Preparing and using for the first time – Determining the water hardness’).

Instruction

Press the 0 or 9 button to change the setting for the water hardness.
Press the
‘Save’ button.
‘Saved’ ‘Filter operation’ / ‘Insert filter’
Remove the water tank and rinse it with cold water.
Fit the filter cartridge extension supplied on top of the CLEARYL Smart filter cartridge.
Insert the filter cartridge with its extension into the water tank.
Turn the filter cartridge clockwise until it audibly clicks into place.
Fill the water tank with fresh, cold water and reinsert the tank.

The machine automatically detects that you have just inserted the filter cartridge.

Saved’
‘Open switch’

Place a receptacle under the fine foam frother.
Turn the switch to the x position.
The filter is rinsed.
Rinsing of the filter stops automatically.

‘Close switch’

Turn the switch to the ° position.

‘System is filling’
‘Empty drip tray’

Empty the drip tray and put it back into the machine.
Place a receptacle under the coffee spout.

‘Machine is rinsing’
The rinse stops automatically. Your E6 is ready for use
Cockpit

You can manage your E6 with the JURA Cockpit. Press the f button to enter the JURA Cockpit.

Symbol	Meaning
‘Maintenance’ section
‘Machine setting’ section
‘Smart mode’ active
Filter mode

Connecting milk

Your E6 creates fine, creamy, feather-light milk foam with a perfect consistency. The most important requirement for frothing milk is a milk temperature of 39–46 °F (4–8 °C). We would therefore recommend using a milk cooler or a milk container.

Connecting milk

Remove the protective cover from the fine foam frother.
Connect the milk pipe to the fine foam frother.

Your E6 is equipped with the HP1 milk system.

Connect the other end of the milk pipe to a milk container or a milk cooler.

Connecting the machine to the WiFi network (optionally)

Your E6 can be connected with your JURA app (J.O.E.®).
Requirement: J.O.E.® is installed on your mobile device. The optionally available JURA WiFi Connect is inserted into the service socket of your E6.

For more information about setting up the WiFi Connect, please go to jura.com/wifi or scan the QR code.
QR code

Preparation

Warning
Hot coffee, hot steam and hot water can cause scalding. Scalding is a serious burn.

Use extreme care when handling hot liquid or steam.
Allow liquid to cool down before drinking.
In the event of scalding, rinse affected area with cold water and seek medical attention.
Keep children AWAY.

Espresso and coffee

Example: Coffee

Place a cup under the coffee spout.
Press the ‘Coffee’ button. The preset amount of water for coffee flows into the cup.

Cappuccino and macchiato

Example: Cappuccino
Precondition: Milk is connected to the fine foam frother.

Place a cup under the fine foam frother.
Press the ‘Cappuccino’ button. ‘Open switch’
Turn the switch to the x position. The preset amount of milk foam flows into the cup ‘Close switch’
Turn the switch to the ° position.
The preset amount of water for espresso flows into the cup.

To ensure that the fine foam frother always works properly, you must clean it daily when you have been preparing milk (see chapter 7 ‘Maintenance – Cleaning the fine foam frother’)

Caffè Barista and lungo Barista

For the ‘caffè Barista’ and ‘lungo Barista’, blend the coffee with hot water. This results in a full-bodied specialty coffee which is particularly easy to digest.
Example: Caffè Barista

Place a cup under the coffee spout and the fine foam frother.
Press the ^ button to go to the second product page.
Press the ‘Caffè Barista’ button. The preset amount of water for coffee flows into the cup. ‘Open switch’
Turn the switch to the x position. The preset amount of hot water flows out of the fine foam frother.
‘Close switch’
Turn the switch to the ° position.

Ground coffee

You can choose to use a second coffee variety, for example decaffeinated coffee, with the filter funnel for ground coffee.

Basic information about ground coffee:

Never add more than two level measuring spoons of ground coffee.
Use ground coffee which is not ground too finely. Very fine coffee can block up the system so that the coffee only comes out in drips.
If you did not fill the machine with a sufficient amount of ground coffee, ‘Not enough ground coffee’ is displayed and the E6 stops the operation.
The desired specialty coffee must be prepared within approximately one minute after filling with the ground coffee. Otherwise the E6 stops the operation and is once more ready for use.
All specialty coffees with ground coffee are always prepared following the same model.

Example: Proceed as follows to prepare an espresso using ground coffee.

Place an espresso cup under the coffee spout.
Press the f button for two seconds to call up Specialty Selection.
Press the ‘Ground coffee’ v button.
Press the ‘Espresso’ button. ‘Ground coffee’ / ‘Please add ground coffee’
Open the cover of the filler funnel for ground coffee.
Place one level measuring spoon of ground coffee into the filler funnel.
Close the cover of the filler funnel.
Press the ‘Next’ button.
The preset amount of water for espresso flows into the cup

Hot water To obtain a perfect water flow, use the hot-water nozzle supplied.

CAUTION

There is a danger of scalding from hot water splashes.

Avoid direct contact with the skin.
Carefully pull the fine foam frother down and off.
Attach the hot-water nozzle to the connector.
Place a cup under the hot-water nozzle.
Press the ^ button to go to the second product page.
Press the ‘Hot water’ button.
‘Open switch’
T Turn the switch to the x position. The preset amount of water flows into the cup.
‘Close switch’
Turn the switch to the ° position.

Adjusting the grinder
You can adjust the grinder to suit the degree of roast of your coffee.

CAUTION

If you adjust the consistency of grind when the grinder is not operating, the grinder adjustment switch could be damaged.

Only adjust the consistency of grind when the grinder is running.

The consistency of grind is correct if the coffee flows regularly from the coffee spout. In addition a fine, thick crema forms.

Grinder adjustment switch

1: Fine consistency of grind setting
2: Coarse consistency of grind setting

Example: Proceed as follows to change the consistency of grind during the preparation of an espresso.

Place a cup under the coffee spout.
Open the cover of the filler funnel for ground coffee.
Press the ‘Espresso’ button to start preparation.
Turn the grinder adjustment switch to the desired position while the grinder is running. The preset amount of water flows into the cup.
Close the filler funnel cover.

Adjusting the product settings

Press a product button on the start screen for about two seconds to view the list of settings.Permanent settings in programming mode always follow the same model.

Example: Proceed as follows to change the coffee strength for one coffee

Press the ‘Coffee’ button for about two seconds.
Press the ‘Product settings’ button.
Press the buttons on the left and right of öää to change the product settings ‘Volume’ and ‘Temperature’.
Press the 0 or 9 button to change the setting for the coffee strength.
Press the ‘Save’ button.
Press the R button to return to the start screen.

Daily operation

Switching the machine on and off

Place a receptacle under the coffee spout and the fine foam frother.
Press the On/Off button

When the machine is switched off, the system is only rinsed if a specialty coffee has been prepared.\\ If milk has been prepared before switching off, you will be prompted to carry out milk system cleaning (‘Clean the milk system’). After 30 seconds the switch-off process continues automatically.

If milk has been prepared but you have not started milk system cleaning, you will first need to rinse the milk system (‘Rinse the milk system’ / ‘Open switch’).

Turn the switch to the x position.
‘Milk system is being rinsed’ ‘Close switch’
Turn the switch to the ° position. The system rinses itself. Your E6 is switched on or off.

Filling the water tank
Daily maintenance of the machine and hygiene when handling milk, coffee and water are key to a perfect coffee result in the cup every time. You should therefore change the water daily

NOTICE
Milk, sparkling mineral water or other liquids can damage the water tank or the machine.

Only fill the water tank with fresh, cold water.
Open the water tank cover.
Remove the water tank and rinse it with cold water.
Fill the water tank with fresh, cold water and reinsert the tank.
Close the water tank cover.

Maintenance actions
Optimal coffee quality depends on many factors. One important prerequisite is regular maintenance of your E6. Carry out the following steps:

Machine settings

Press the f button to enter the cockpit. In the ‘Machine setting’ f section, you can make the following settings:

‘Connections'(Only displayed if JURA WiFi Connect is being used.)Wirelessly connect your E6 with your JURA app (J.O.E.’) or with the Cool Control milk cooler, or disconnect again

‘Switch off after’| Set the automatic switch-off time to save energy (switch- off after15 minutes, 30 minutes or 1- 9 hours after the last action on the machine)
---|---
‘Water hardness’| Set the hardness of the water used (1 °dH to 30 °dH) to prevent calcification of your machine
‘Product name’ ‘Smart mode’| | Display product images with/without product names on the start screen Arrange products by preparation frequency on the start screen after a certain amount of time (the * symbol in the Cockpit shows that ‘Smart mode is activated)
‘Factory setting’ ‘Version’| Reset your E6 to factory settings (the machine then switches off)
View software version

Maintenance

WARNING
Use of maintenance products that are harmful to health and discharge of liquids during maintenance program. Harmful if swallowed. Irritating to eyes and skin.

Keep children AWAY.
Keep children away from the machine while it is performing a maintenance program.
Avoid contact with skin and eyes.
Avoid generation of dust. Do not inhale dust.
When using do not eat or drink.
Keep maintenance products away from food, drink and animal food.
Keep container tightly closed and dry. Keep in a cool place.

Basic information about maintenance:

Press the f button to enter the Cockpit. This area consists of a ‘Maintenance’ c section and a ‘Machine setting’ f section. You can manage the maintenance of your E6 in the c section.
If a maintenance program needs to be initiated, the f symbolappears with a red background. Press the f button to enter the Cockpit. The Cockpit shows maintenance programs that need to be carried out in the form of messages with red backgrounds. Press the button that corresponds to the message to go straight to the maintenance program. Maintenance programs that are due imminently are indicated on your E6 by means of a bar display within the message.
Carry out each maintenance program when you are prompted to do so.

Rinsing the machine

You can start coffee system rinsing manually at any time.

Place a receptacle under the coffee spout.
Press the f button.
Press the c button.
Press the ‘Rinse the coffee system’ button to start the rinse operation. The operation stops automatically

Rinsing the milk system
After each milk preparation, the E6 prompts you to perform a milk system rinse.

Place a receptacle under the fine foam frother.
Press the f button.
Press the ‘Rinse the milk system’ button.
‘Open switch’
Turn the switch to the x position. The fine foam frother is rinsed.
‘Close switch’
Turn the switch to the ° position.

Cleaning the fine foam frother
To ensure that the fine foam frother always works properly, you must clean it daily when you have been preparing milk.

WARNING
Non-recommended cleaning agents will not optimally remove milk residues. This may cause the cappuccino frother to become blocked and fly off the machine. Discharge of hot steam.

Use only original JURA milk system cleaner.

WARNING
Harmful and irritating cleaning agent. Harmful if swallowed. Irritating to eyes and skin.

Keep children AWAY.
Avoid contact with skin and eyes.
After contact with skin, wash immediately with plenty of water. In case of skin irritation, seek medical advice.
After eye contact, immediately flush eyes with plenty of water and seek medical advice.
If swallowed, rinse mouth immediately and drink large quantities of water. Do not induce vomiting. Seek medical advice immediately and show label.

JURA milk system cleaner is available from specialized dealers.
Use the container supplied for milk system cleaning.

Press the f button.
Press the c button.
Press the ‘Clean the milk system’ button.
Press the ‘Start’ button.
‘Milk system cleaner’
Remove the milk pipe from the milk container or milk cooler.
Pour one dosing unit of milk system cleaner into the container for milk system cleaning.
Then fill with warm water up to the upper mark.
Place the container under the fine foam frother.
Connect the milk pipe to the container.

To connect the milk pipe to the container correctly, the pipe must be fitted with a connector.

Instruction

Press the ‘Next’ button. As soon as the machine has heated up, ‘Open switch’ appears.
Turn the switch to the x position. The fine foam frother and the milk pipe are cleaned.
‘Close switch’
Turn the switch to the ° position.
‘Fresh water’
Rinse the container thoroughly and fill the front part with fresh water up to the upper mark.
Place the container under the fine foam frother and reconnect the milk pipe to the container.
Press the ‘Next’ button.
‘Open switch’
Turn the switch to the x position.
The fine foam frother and the milk pipe are rinsed with fresh water.
‘Close switch’
Turn the switch to the ° position.

Dismantling and rinsing the fine foam frother

If insufficient foam is produced when the milk is frothed or milk sprays out of the fine foam frother, this may get dirty. If this happens, dismantle and rinse the fine foam frother.

Remove the milk pipe and rinse it thoroughly under running water.
Carefully pull the fine foam frother down and off.
Dismantle the fine foam frother into its individual parts.
Rinse all the parts under running water. If there are severely dried-on milk residues, firstly immerse the individual parts in a solution of 8.5 oz (250 ml) water and one dosing unit of JURA milk system cleaner. Then rinse the individual parts thoroughly.
Re-assemble the fine foam frother.
Ensure that all individual parts are correctly and firmly connected to ensure optimum operation.
Reattach the fine foam frother to the connector.

Inserting/changing the filter

Once the filter cartridge stops working (depending on the water hardness setting), the E6 will prompt you to change the filter.

Your E6 no longer has to be descaled if you are using the CLEARYL Smart filter cartridge.
CLEARYL Smart filter cartridges are available from specialized dealers.

Precondition: The start screen is displayed. (Alternatively, the filter symbol $ is displayed in red in the cockpit if the filter’s capacity has been exhausted.

Remove and empty the water tank.
Turn the filter cartridge anticlockwise and remove it along with the extension from the water tank.
Fit the filter cartridge extension on top of a new CLEARYL Smart filter cartridge.
Insert the filter cartridge with its extension into the water tank.
Turn the filter cartridge clockwise until it audibly clicks into place.
Fill the water tank with fresh, cold water and reinsert the tank.

The machine automatically detects that you have just inserted/changed the filter cartridge

Saved’ ‘Open switch’

Place a receptacle under the fine foam frother.
Turn the switch to the x position. The filter is rinsed.

‘Close switch’

Turn the switch to the ° position.

Cleaning the machine

fter 180 preparations or 80 switch-on rinses, the E6 will prompt you to clean it.

WARNING

Harmful and irritating cleaning agent. Harmful if swallowed. Irritating to eyes and skin.

Keep children AWAY.
Avoid contact with skin and eyes.
Avoid generation of dust. Do not inhale dust.
After contact with skin, wash immediately with plenty of water. In case of skin irritation, seek medical advice.
After eye contact, immediately flush eyes with plenty of water and seek medical advice.
If swallowed, rinse mouth immediately and drink large quantities of water. Do not induce vomiting. Seek medical advice immediately and show label.

The cleaning program lasts approximately 20 minutes.
Do not interrupt the cleaning program. The quality of cleaning will be impaired if you do so.
JURA cleaning tablets are available from specialized dealers.

Precondition: ‘Clean’ is displayed in the cockpit.

Fill the water tank.
Press the ‘Clean’ button.
Press the ‘Start’ button.
‘Empty grounds’
Empty the drip tray and coffee grounds container and put them back into the machine.
‘Clean’
Place a receptacle under the coffee spout.
Press the ‘Next’ button. Water flows out of the coffee spout. The operation is interrupted, ‘Add cleaning tablet’.
Open the cover of the filler funnel for ground coffee.
Insert a JURA cleaning tablet into the filler funnel.
Close the cover of the filler funnel.
Press the ‘Next’ button. Water flows out of the coffee spout several times.
‘Empty grounds’
Empty the drip tray and coffee grounds container and put them back into the machine.

Descaling the machine

The E6 builds up deposits of limescale over time and automatically prompts you to descale it when necessary. The degree of calcification depends on the hardness of your water. If you are using a CLEARYL Smart filter cartridge, you will not be prompted to descale.

NOTICE

If the descaling operation is interrupted, there may be damage to the machine.

Allow the descaling program to run to the end.

The descaling program lasts approximately 40 minutes.
JURA descaling tablets are available from specialized dealers.
If the descaling agent comes into contact with sensitive surfaces (e.g. marble), damage cannot be ruled out. Clean up any splashes immediately

Precondition: ‘Descale’ is displayed in the Cockpit.

Press the ‘Descale’ button.
Press the ‘Start’ button.
‘Empty drip tray’
Empty the drip tray and coffee grounds container and put them back into the machine.
‘Agent in tank’
Remove and empty the water tank.
Completely dissolve 3 JURA descaling tablets in a receptacle holding 17 oz (500 ml) of water. This may take several minutes.
Pour the solution into the empty water tank and insert it into the machine.
‘Open switch’
Place a receptacle under the fine foam frother.
Turn the switch to the x position.
‘Machine is being descaled’ appears and water flows out of the fine foam frother repeatedly. The operation is interrupted, ‘Close switch’.
Turn the switch to the ° position.
‘Machine is being descaled’, the descaling operation is continued. The operation is interrupted, ‘Empty drip tray’.
Empty the drip tray and coffee grounds container and put them back into the machine.
‘Rinse the water tank’ / ‘Fill water tank’
Remove the water tank and rinse it thoroughly.
Fill the water tank with fresh, cold water and reinsert the tank.
‘Open switch’
Empty the receptacle and place it under the fine foam frother and the coffee spout.
Turn the switch to the x position.
‘Machine is being descaled’, the descaling operation is continued. The operation is interrupted, ‘Close switch’.
Turn the switch to the ° position. The descaling operation is continued. Water flows out of the coffee spout.
The operation is interrupted ‘Empty drip tray’
Empty the drip tray and coffee grounds container and put them back into the machine.
If the descaling operation stops unexpectedly, rinse the water tank thoroughly

Descaling the water tank

Limescale deposits may form in the water tank. To ensure correct function of the machine, descale the water tank from time to time.

Remove the water tank.
If you use a CLEARYL Smart filter cartridge, remove this.
Completely fill the water tank and dissolve 3 JURA descaling tablets in it
Leave the water tank with the descaling solution for several hours (e.g. overnight).
Empty the water tank and rinse it thoroughly.
If you use a CLEARYL Smart filter cartridge, insert this again.
Fill the water tank with fresh, cold water and reinsert the tank.

Cleaning the bean container

Coffee beans may be covered with a slight oil film which remains on the walls of the bean container. These traces may negatively affect the coffee result. For this reason clean the bean container from time to time.

Precondition: ‘Fill bean container’ is displayed.

Switch the machine off with the On/Off button Q.
Remove the aroma preservation cover.
Clean the bean container with a soft, dry cloth.
Fill the bean container with coffee beans and close the aroma preservation cover.

Display messages

Messages in the cockpit

Message	Cause/Result	Action
The filter symbol $	The filter cartridge no	T Replace the CLEARYL Smart

Troubleshooting

Problem	Cause/Result	Action

Insufficient foam isproduced when the milkis frothed or milk spraysout of the fine foamfrother.| The fine foam frother isdirty.| T Clean the fine foam frother (seechapter 7 ‘Maintenance – Cleaning thefine foam frother’).T Dismantle and rinse the fine foamfrother (see chapter 7 ‘Maintenance –Dismantling and rinsing the fine foamfrother’).
Coffee only comes outin drips when it is beingprepared.There is dry groundcoffee behind the coffeegrounds container.| The coffee is ground toofinely and obstructs thesystem. The water hardnessmay not have beencorrectly set.The beans used areresulting in an above-average volume of groundcoffee.| T Set the grinder to a coarser setting(see chapter 4 ‘Preparation – Adjustingthe grinder’).T Perform descaling (see chapter 7‘Maintenance – Descaling the machine’).T Reduce the coffee strength or choose afiner grinder setting (see chapter 4‘Preparation – Adjusting the grinder’).
‘Fill water tank’ is notdisplayed, even thoughthe water tank is empty.Little or no water orsteam comes out of thefine foam frother. Thepump is very quiet.| There is a lot of limescale inthe water tank.The connector of the finefoam frother may beblocked by milk residues orlimescale fragmentsloosened during descaling.| T Descale the water tank (see chapter 7‘Maintenance – Descaling the watertank’).T Remove the fine foam frother.T Unscrew the black connector with theaid of the hexagonal hole on themeasuring spoon for ground coffee.T Clean the connector thoroughly.T Screw the connector back on tightly byhand.
Grinder is making a veryloud noise.| There are foreign objects inthe grinder.| T Contact customer support in yourcountry (see chapter 13 ‘JURA contactdetails / Legal information’).
‘ERROR 2’ or ‘ERROR 5’is displayed.| If the machine has beenexposed to the cold for along period of time,heating may be disabledfor safety reasons.| T Warm the machine at roomtemperature.
Other ‘ERROR’ mes-sages are displayed.| –| T Contact customer support in yourcountry (see chapter 13 ‘JURA contactdetails / Legal information’).

Transport and environmentally friendly disposal

Transport / Emptying the system

Keep the packaging for your E6. It should be used to protect the machine during transport. In order to protect the E6 from frost during transport, the system must be emptied.

Remove the milk pipe from the fine foam frother.
Place a receptacle under the fine foam frother.
Press the ^ button to go to the second product page.
Press the ‘Hot water’ button.
‘Open switch’
Turn the switch to the x position. Water flows out of the fine foam frother.
Remove and empty the water tank.
‘Close switch’
Turn the switch to the ° position.
‘Fill water tank’
Press the On/Off button Q. Your E6 is switched off.

Disposal

Please dispose of old machines in an environmentally neutral way.

Technical data

Voltage 120 V ~, 60 Hz
Power 1450 W
Conformity mark
Pump pressure static, max. 15 bar
Holding capacity of water tank (without filter) 64 oz (1.9 l)
Holding capacity of bean container 10 oz (280 g)
Holding capacity of coffee grounds container max. 16 portions
Cord length approx. 47 in. (1.2 m)
Weight approx. 19.8 lb (9.0 kg)
Dimensions (W × H × D) 11.0 × 13.8 × 17.6 in. (28.0 × 35.1 × 44.6 cm)
Milk system HP1
Interchangeable milk spout CX3
CLEARYL Smart filter cartridge (RFID technology) Frequency band 13.56 MHz Max. transmission power < 1 mW
JURA WiFi Connect Frequency band 2.4 GHz Max. transmission power < 100 mW