STUDER next 3 rack next3 Device User Guide

October 30, 2023
STUDER

next 3 rack next3 Device
User GuideSTUDER next 3 rack next3 Device

next 3 rack next3 Device

swiss made power
designed and assembled by studer in Switzerland ***** The studercare+ program allows to extend the warranty 6 additional years along with further features.

Introduction

Congratulations!
You are about to install and use a high-end equipment that will play a central role in the energy management of your battery-based system. The next3 is the first device of our new generation of smart battery inverter/charger with advanced functions.
This next3 has been designed, manufactured, assembled and tested in our factory in Switzerland. It has a 6-year warranty and is eligible for an extension 6+6, under the studercare+ program (not yet available, check with your studer representative for further information).

General Information

| STUDER next 3 rack next3 Device - Symbol 4| STUDER next 3 rack next3 Device - Symbol 5
---|---|---

STUDER next 3 rack next3 Device - qr codehttps://technext3.studer-innotec.com

Exclusion of liability
Studer disclaims all responsibility and liability for damage, costs or losses resultingfrom an installation that does not comply with the instructions, a faulty operation or inadequate maintenance. The use of studer equipment is in any case under theresponsibility of the customer.
Read carefully the safety and operation instructions / Installation must be entrusted to qualified personnel / Check the user manual online / Need help?
Options & accessories:

STUDER next 3 rack next3 Device - standard nx3 rack st
next3 full option (standard)| STUDER next 3 rack next3 Device -
interface nx3 rack sti
next3 full option + interface
---|---
nx tempSensor
next3 battery temperature sensor| nx interface
next3 user interface

Mounting and installation

Storage and contentSTUDER next 3 rack next3 Device - Storage and
content Mounting place
The next3 and the batteries should only be installed by qualified personnel. STUDER next 3 rack next3 Device - Mounting placeFixing and dimensionsSTUDER next 3 rack next3 Device - Fixing
and dimensions

Wiring

STUDER next 3 rack next3 Device - Wiring **** The device must be installed in accordance with local standards and regulations in force.

Communication and power up

1 nx interface required in the communication busSTUDER next 3 rack
next3 Device - power up

Display

Display systemSTUDER next 3 rack next3 Device - Display
system Configuring the next
nx interfaceSTUDER next 3 rack next3 Device - Configuring the
next Multi units
3 phase and parallel combinationSTUDER next 3 rack next3 Device -
parallel combination

Technical data

STUDER next 3 rack next3 Device - inverter

inverter nx3 rack 16000-48 st
Continuous Power 15000 VA
Power 30min 16000 VA
Power 5sec 30000 VA
AC output voltage 230V Phase to Neutral / 400V Phase to Phase
AC output frequency 50/60Hz

solar

Solar MPPT inputs 2
PV input voltage 100 – 900 Vdc
PV startup voltage 200 Vdc
PV max current 2 x 27 Adc
PV power 2 x 8 kW

transfer

Max rated current 3 x 80 Aac
Phase to neutral voltage 230 Vac
Phase to phase voltage 400 Vac
Frequency 50/60 Hz

Battery nominal voltage 48Vdc (38-68Vdc)
Battery charge current 300 Adc

Maintenance and recycling

Maintenance and recycling
Except for the periodic check of the connections (tightening, general condition), the next does not require any particular maintenance. To dispose of this product, please use the service for the collection of electrical waste and observe all obligations in force in the place of purchase.

Serial Number:
Installed by:
Date:
Signature:
Call our specialists +41 27 205 60 80 or visit studer- innotec.com/support
Studer Innotec SA
rue des Casernes 57
1950 Sion, Switzerland
info@studer-innotec.com

4O92STUDER next 3 rack next3 Device - Symbol 7 ©All rights reserved
Studer Innnotec SA – V1.1

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals