Godox AD600 ProII All in One Outdoor Flash Instruction Manual

Godox AD600 ProII All in One Outdoor Flash

Important Safety Instructions

This product is professional photographic equipment, to be operated by professional personnel only.
The following basic safety precautions must be followed when using this product:

All transport protective materials and packaging on the product must be removed before use.

1. Carefully read and fully understand the instruction manual before use and strictly follow the safety instructions. Failure to do so may result in death, serious injury, damage to the product, or other property damage.
2. High voltage exists when the flash is powered on. Internal capacitors will remain charged for some time after power off.
3. This product is a professional lighting fixture, children are prohibited from using it. Children must be closely supervised by adults when approaching the fixture, to prevent collisions with the fixture or unauthorized use that could cause personal injury.
4. This is not an ordinary lighting fixture and must not be used for general illumination. Anyone with a history of eye damage or sensitivity should avoid using this fixture or looking directly at it.
5. Extreme caution must be exercised when using it, do not touch high-temperature parts such as flash tubes to avoid burns.
6. Do not point the flash directly at the eyes (especially baby’s eyes) under any circumstances, as this could impair vision in a short time. Turn off immediately if discomfort occurs, stop using, and seek medical attention promptly.
7. If the flash tube is damaged, stop using it immediately and contact the manufacturer, service agent, or qualified repair personnel for a replacement to prevent accidents.
8. Dot not use damaged equipment or accessories. Allow professional repair technicians to inspect and confirm normal operation before continuing use after repairs.
9. Disconnect power source or remove batteries (if it has one) before replacing flash tube, protective glass, or fuses. Allow 10 minutes to cool before replacing flash tube, and wear insulated or heat resistant gloves when operating.
10. Turn off power before connecting or disconnecting plugs from outlets. Ensure plugs are fully inserted when connecting.
11. Stop using immediately if the product shell is cracked due to falling, squeezing, or strong impact, to avoid touching the internal electronic components and getting an electric shock.
12. Some products have long power cords, please place them properly to avoid contact with heat sources or tripping others. It is recommended to use the original power cord. Damage caused by non-original cords is not covered by the warranty.
13. Unplug the equipment power plug from the power socket before cleaning or maintenance. Do not pull the power cord forcibly, use both hands to hold the plug end and pull it out.
14. This device is not waterproof. Keep it dry and avoid immersing it in water or other liquids. It should be installed in a ventilated and dry location and avoid using in rainy, humid, dusty, or overheated environments. Do not place items above the device or allow liquids to flow into it to prevent danger.
15. Do not disassemble without authorization. If the product malfunctions, it must be inspected and repaired by our company or authorized repair personnel.
16. Before storing the device, ensure it has completely cooled down and the power cord is unplugged, then put it in the protective case or a ventilated dry location.
17. Do not place the device near alcohol, gasoline, or other flammable volatile solvents or gases such as methane and ethane.
18. Do not use or store this device in potentially explosive environments.
19. Do not cover the heat dissipation port!
20. Do not use accessories not been approved by our company, as this may cause fire, electric shock or personal injury.
21. Clean gently with a dry cloth. Do not use a wet cloth as it may damage the device.
22. Some products are equipped with protective covers that must be removed before use.
23. This instruction manual is based on rigorous testing. Changes in design and specifications are subject to change without notice. Check official website for latest instruction manual and product updates.
24. Use only specified charger and follow proper usage instructions for certain products with built-in lithium batteries, within the rated voltage and temperature range.
25. Some products are powered by lithium batteries, who have limited lifespans and will gradually lose their charging capacities, which is irreversible. As the battery ages, the product’s battery life will decrease. The lifespan of lithium battery is estimated to be 2 to 3 years. Please regularly check the battery, and if the charging time significantly increases or the battery life significantly decreases, consider replacing the battery.
26. Some products are equipped with lithium batteries. The following are the storage recommendations: Charge the battery to about 50% before storage. Charge it to about 50% at least every six months. Removable batteries should be stored separately. The storage temperature should be between 0°C and 40°C.
27. Some products are powered by lithium batteries. Please note:
    • Do not disassemble, crush, or puncture the battery;
    • Avoid short-circuiting the battery contacts;
    • Do not expose the battery to fire or water;
    • Do not expose the battery to temperatures above 60°C;
    • Keep out of reach of children;
    • Protect the battery from excessive shock or vibration;
    • Do not use a damaged battery;
    • If the battery leaks, avoid contact with the leaking fluid;
    • If the battery fluid comes into contact with your eyes, immediately rinse with water for at least 15 minutes. Lift your eyelids until there are no signs of fluid and seek medical attention promptly.
28. Confirm and comply with all relevant local laws and regulations when handling any batteries. The warranty period for this device as a whole is one year. Consumables (such as batteries), adapters, power cords, and other accessories are not covered by the warranty.
29. Unauthorized repairs will void the warranty and will incur charges.
30. Failures from improper operation is not covered under warranty.

Foreword

Thank you for purchasing!

AD600ProII has strong power, detachable lithium battery pack and great portability. When using Godox 2.4G wireless X system, it can be triggered by XPro/XProII/X2T/X3 series flash trigger in M/Multi/TTL mode. With transmitter & receiver functions, AD600ProII can also use in combination with Godox camera flashes, outdoor flashes, studio flashes, etc. With this flash, your shooting will become simpler. With high-speed shooting throughout the process, single fixture overshadowing the sunlight, bare flash tube and reflector make a perfect match for outdoor and live shooting, AD600ProII is an ideal light source for freelance commercial photographers, journalists, photography enthusiasts, wedding documentary photographers, etc.

Main Features

• Quick Recycle Time: 0.01s~0.9s (max. power).
• Stable Color Temperature: shift around ±100K over the entire power range with this function.
• LED Modeling Lamp: 40W bi-color large LED modeling light freely adjusts brightness and CCT.
• Studio Quality Light: up to 600Ws, GN 87 (m ISO 100, with efficient reflector), 360 full power flashes, 1/8000s high-speed sync.
• Precise Power Adjustment: from full power 1/1 to 1/512 with 0.1 increment each step.
• Wide Compatibility: fully support M, Multi and wireless TTL flash systems of Canon, Nikon, Fujifilm, Olympus, Sony, Leica, Pentax, etc. Workable as a receiver unit in a wireless flash group.
• Wireless Control: with built-in 2.4G wireless X system to achieve remote control by optional Godox flash triggers, and 3.5mm sync cord jack to achieve various sync triggering modes.
• Distinct Group Colors: 16 groups with different colors to quickly distinguish even in remote distance usage.
• Simple Operation: 2.8″ color screen together with steplessly rotatable select dial, detachable battery pack design.
• Wide-range Accessories: Bowens mount has wide compatibility and versatility.

Warning

• Always keep this product dry.
• Do not disassemble. Should repairs become necessary, this product must be sent to an authorized maintenance center.
• Stop using this product if it breaks open due to extrusion, falling or strong hit. Otherwise, electric shock may occur if you touch the electronic parts inside it.
• Do not leave or store the flash unit if the ambient temperature reads over 50°C.
• Do not fire the flash directly into the eyes (especially those of babies) within short distances.
• Otherwise visual impairment may occur.
• Do not use the flash unit in the presence of flammable gases, chemicals and other similar materials. In certain circumstances, these materials may be sensitive to the strong light emitting from this flash unit and fire or electromagnetic interference may result.
• This product is not waterproof, do not use in rain or in damp conditions.
• Please remove the flash head protection cover before using.

CAUTION

• Hot surface.
• Do not touch.
• Burned fingers when handling the parts.
• Wait one-half hour after switching off before handling parts.

Name of Parts

Flash Body

1. Flash Tube
2. Color Screen
3. MENU Bu tton
4. MODE Button
5. Select Dial
6. SET Button
7. Power Switch/Test Button
8. Modeling Lamp Button
9. Bracket Locking Knob
10. Handle Fixing Fastener
11. Handle
12. Accessory Locking Pusher
13. USB-C Port
14. 3.5mm Sync Cord Jack
15. Group Indicator x2
16. Photocell Receiver
17. Battery Indicator Button
18. Battery Charging Port
19. Battery Level Indicator
20. Battery Compartment Pusher
21. Reflector

What’s Inside

Separately Sold Accessories

• Flash Head: H600P Portable Flash Head.
• Power Supply AC26 Power Source,UC46 USB Charger.
• Flash Triggec XPro, XProl I, X2T, X3 series.
• Optical Accessories: Umbrella Softbox,Collapsible Lantern Softbox, Quick-loading Parabolic Softbox, Beauty Dish, Umbrella Diffuser, Snoot, Light Stand, etc.

Installing and Disassembling

Installing and Disassembling Reflector/Flash Tube

• Installing the Reflector: Insert the reflector into the accessory mount , press and hold then rotate clockwise, the accessory locking pusher will lock up.
• Disassembling the Reflector: Press down the accessory locking pusher, rotate the reflector anticlockwise to unlock.
• Installing the Flash Tube: Press down the accessory locking pusher, remove the reflector or other accessories. Match the flash tube in the tube socket and push until it is securely seated into the socket.
• Disassembling the Flash Tube: Press down the accessory locking pusher, remove the reflector or other accessories. Grasp the flash tube and pull it out horizontally.

Note: Please wear gloves for the above operations.

Adjusting Flash Angle

1. When the handle fixing fastener is not pulled out, rotate the handle anticlockwise to unlock it, adjust the flash body for the desired angle, then rotate the handle clockwise to tighten.
2. If the handle collides the flash body in rotation, please press the handle fixing fastener and pull out the handle, repeat the step 1 after stretching out a few distance.

Power Switch And Color Screen

Power Switch

1. Long press the power switch button until the unlock icon < > is displayed on the panel, then rotate the select dial clockwise to turn on the device.
2. Long press the power switch button for until panel black out to turn off the device.

Note

• Turn off the device if it will not be used for an extended period. This device is designed with an automatic power off function, which can be set in menu settings.

Color Screen

1. M (Manual) Flash
2. Multi Flash
3. TTL Auto Flash

Battery

Features

1. This flash unit uses lithium battery which has long runtime. The available charge-and-discharge times are 300.
2. It is reliably safe. The inner circuit is against overcharge, overdischarge, overcurrent, and short circuit.
3. It takes only 2 hours to fully charge the battery by using the standard battery charger.

Cautions

• Do not short circuit.
• Do not expose to rain or immerse into water. This battery is not water proof.
• Keep out of reach of children.
• No over 24 hours’ continuous charging.
• Store in dry, cool, ventilated places.
• Do not put aside or into fire.
• Dead batteries should be disposed according to local regulations.
• If the battery had ceased using for over 3 months, please make a full recharge.

Loading and Unloading the Battery

1. Loading: Match the battery’s groove with the main battery compartment’s ridge. Push down the battery pack until it is locked.
2. Unloading: Push the battery compartment pusher and the battery pack upward at the same time to unload it.

Battery Level Indication

Attach the battery pack to the flash correctly. Check the battery level by pressing the battery indicator button and lightening the battery level indicator as the following table shows.

LED Battery Level Indication on the Battery

(Indicating battery level and management of non-loaded battery)

| Meaning/Percentage of Battery Level
---|---
1 red grid +3 green grids| 75% ～ 100%
1 red grid +2 green grids| 50% ～ 75%
1 red grid +1 green grid| 25% ～ 50%
1 red grid| 3% ～ 25%
2% flash red, 1% off| ＜ 2%

The battery level is going to be used out immediately. And the flash will alarm for 1 minute and auto power off in 3 minutes.

Note: Please recharge the battery as soon as possible (within 10 days). Then, the battery can be used or be placed for long period.

Note: The indications are almost the same except for the grids shift.

Battery Activation Instructions

Due to the battery upgrade, if you haven’t used the battery for more than a month, it will automatically go to sleep. please try to activate it if you use or charge again after a month.

• Activation method: Short press the right side of battery indicator button to activate.

Display Instructions

High-Speed Sync

High speed sync (FP flash) enables the flash to synchronize with all camera shutter speeds. This is convenient when you want to use aperture priority for fill-flash portraits.

1. Press the MENU button to enter menu interface, turn the select dial and press the SET button to enter high speed sync and turn on it. Then press MENU button to return to the main interface, the HSS icon < **** > can be seen on the panel.
2. Please use Xl /XProl /XProll /X2T/ X3 series flash triggers.

Note:

• If you set a shutter speed that is the same as or slower than the camera’s maximum flash sync speed,< **** > will not be displayed in the viewfinder.
• With high-speed sync, the faster the shutter speed, the shorter the effective flash range.
• To return to normal flash, turn off the high-speed sync function in menu settings. Then< **** > will disappear.
• Multi flash mode cannot be set in high-speed sync mode.
• Over-temperature protection may be activated after 64 consecutive high-speed sync flashes.

M: Manual Flash

• The flash output is adjustable from 1 /1 full power to 1/512 power with 0.1 step increment. To obtain a correct flash exposure, use a hand-held flash meter to determine the required flash output.
• Press MODE button so that< M > is displayed.
• Turn the select dial to choose a desired flash output amount.

Flash Output Range

The following table makes it easier to see how the step changes in terms of aperture value when you increase or decrease the flash output.
Turn the select dial clockwise to increase the flash output, while turn it anticlockwise to decrease the flash output.

Optical S1 Secondary Unit Setting

Press MENU button to enter photocell and choose S1 function, so that this flash can function as an optical S1 secondary flash with optical sensor in M manual flash mode. Then press then MENU button to return to the main interface. With this function, the flash will fire synchronously when the main flash fires, the same effect as that by the use of wireless triggers. This helps create multiple lighting effects.

Optical S2 Secondary Unit Setting

Press MENU button to enter photocell and choose S2 function, so that this flash can also function as an optical S2 secondary flash with optical sensor in M manual flash mode. Then press then MENU button to return to the main interface. This is useful when cameras have pre-flash function. With this function, the flash will ignore a single “preflash” from the main flash and will only fire in response to the second, actual flash from the main unit.

Note

• S1 and S2 optical triggering is only available in M manual flash mode.

Display Flash Duration

Flash duration refers to the length of time that from flash’s firing to reach the half peak at maximum. The half peak at maximum is usually expressed as t=0.5. In order to provide the photographer with more concrete data, this product adopts t=O.l. The difference between t=0.5 and t=O.l is shown in the following picture.

Note

• Turn off the high speed sync function in M mode, the flash duration will then be displayed.

Multi: Stroboscopic Flash

With stroboscopic flash, a rapid series of flashes is fired. It can be used to capture multiple images of a moving subject in a single photograph. You can set the flash output, number of flashes, and flash frequency (number of flashes per sec. expressed as Hz).

1. Press the MODE button so that < MULTI > is displayed, turn the select dial to choose a desired flash output.
2. Press the SET button and turn the select dial to set the number of flashes.
3. Press the SET button and turn the select dial to set the flash frequency.

Calculating the Shutter Speed

• During stroboscopic flash, the shutter remains open until the firing stops. Use the formula below to calculate the shutter speed and set it with the camera.
• Number of Flashes / Flash Frequency = Shutter Speed
• For example, if the number of flashes is 10 and the firing frequency is 5 Hz, the shutter speed should be at least 2 seconds.

Note:

• Stroboscopic flash is most effective with a highly reflective subject against a dark background.
• Using a tripod and a TTL flash trigger is recommended.
• A flash output of 1 /1 and 1 /2 cannot be set for stroboscopic flash.
• Stroboscopic flash can be used with “bulb”.
• If the number of flashes is displayed as “–“, the firing will continue until the shutter closes or the battery is exhausted. The number of flashes will be limited as shown by the following table.

Maximum Stroboscopic Flashes:

TTL Auto Flash

• In TTL mode, the camera’s metering system detects the flash reflected from the subject and automatically adjusts the flash output so that the subject and background are evenly exposed.
• Press the MENU button to enter menu interface, turn the select dial and press the SIT button to enter wireless and turn on it, set the group among A to E. Press the MENU button to return to the main interface.
• Press MODE button to enter TTL mode, the screen will display< TTL>.

Wireless (2.4G) Transmission

AD600ProII adopts 2.4G wireless X system, which has good compatibility with other Godox products. It can automatically switch to receiver unit according to the transmitter unit instead of setting manually. The compatible cameras include Canon, Nikon, Sony, Olympus, Panasonic, Fujifilm, Pentax, Leica, etc.
As a receiver unit, AD600ProII can be controlled by the following transmitter units: XPROII series/X3 series /X2T series /V1Pro series /V1 series /V860III series.

Wireless Settings

Press the MENU button to enter menu interface, turn the select dial and press the SET button to choose among wireless/channel/group/ID/wireless sync, then turn the select dial and press the SET button to adjust the parameters. Press the MENU button to return to the previous menu, press again to return to the main interface.

Setting the Communication Channel

If there are other wireless flash systems nearby, you can change the channel to prevent signal interference. The channels of the transmitter unit and the receiver unit(s) must be set to the same.

Take X3 flash trigger as an example:

1. Turn off the camera and mount the flash trigger on camera hot shoe. Then, power on the flash trigger and the camera.O
2. Slide the screen of X3 down from the top to display , press to enter C.Fn. menu, then press to set CH and ID. Slide the screen from the left to the right to return to the main interface, on which you can set the flash mode and output power level of groups.
3. Press the MENU button of AD600Proll to select wireless and turn it on, then set the CH and ID the same to the flash trigger.
4. Press the wireless sync on the trigger and flash, then press the SET button on the flash can set their CH and ID to the same.
5. Press the camera shutter to trigger.

Wireless Flash Shooting

Positioning and Operation Range (Example of wireless flash shooting)

Wireless Multiple Flash Shooting

You can divide the receiver units into two or three groups and perform TTL auto flash while changing the flash ratio (factor). In addition, you can set and shoot with a different flash mode for each firing group.

• Auto flash shooting with two receiver units
• Auto flash shooting with three receiver units

Flash Mode

Press the MENU button to enter menu interface, turn the select dial and press the SET button to enter flash mode, in which you can choose among normal, color and freeze.

group indicator will blink and the beeper will beep for 1min if it has been turned on, please press the test button to resume to normal use. The stable color temperature function is only available in non-HSS M mode, and value of which will shift around ±100K over the entire power range
Freeze| Freeze mode, with< ®>on the main interface. The flash duration is shorter than the normal flash mode, and the power is also less than the normal flash mode. The freeze mode is only available in M mode and Multi mode.

The Reason & Solution of Not Triggering in Godox 2.4G Wireless

1. Disturbed by the 2.4G signal in outer environment (e.g. wireless base station, 2.4G wifi router, Bluetooth, etc.)
   • To adjust the channel CH setting on the flash trigger (add l 0+ channels) and use the channel which is not disturbed. Or turn off the other 2.4G equipment in working.
2. Please make sure that whether the flash has finished its recycle or caught up with the continuous shooting speed or not {the flash ready indicator is lightened) and the flash is not under the state of over-heat protection or other abnormal situation.
   • Please downgrade the flash power output. If the flash is in TTL mode, please try to change it to M mode.
3. Whether the distance between the flash trigger and the flash is too close or not ( < 0.5m).
   • Please turn on “short distance wireless mode” of the flash trigger.
   • Xl Series: Press and hold the triggering button then turn on the device, until the indicator blinks twice.
   • XPro and X2T Series: Please set the C.Fn-DIST to 0-30m.
   • X3 Series: Please set the triggering distance to 0-30m.
4. Whether the flash is in the low battery states or not.
   • Please charge or replace the battery in time, and ensure both devices have enough battery power.

Modeling Lamp

AD600ProII is equipped with 40W bi-color LED modeling lamp. Press the modeling lamp button to enter modeling lamp settings, turn the select dial to choose among off/free/prop, then turn the select dial and press the SET button to adjust the parameters. Press the modeling lamp button to return to the main interface.

OFF| Brightness ( in 1% increment )| CCT ( in 100K increment )
---|---|---
FREE| 10%-100%| 2800K-6000K
PROP| Brightness follows flash power| 2800K-6000K

Setting Custom Functions

C.Fn: Setting Custom Functions

Press the MENU button to enter menu interface, turn the select dial and press the SET button to choose among the following functions, then turn the select dial and press the SET button to adjust its parameters. Press the MENU button to return to the previous interface, press again to return to the main interface.

Sync Triggering

• The sync cord jack is a Φ3.5mm plug. Insert a trigger plug in and the flash will be fired synchronously with the camera shutter.

Protection Function

Over-Temperature Protection

• To avoid overheating and deteriorating the flash head, do not fire more than 80 continuous flashes in fast succession at 1/1 full power. After 80 continuous flashes, allow a rest time of at least 10 minutes.
• If you fire more than 80 continuous flashes and then fire more flashes in short intervals, the inner over-temperature protection function may be activated and make the recycling time over 10 seconds. If this occurs, allow a rest time of about 10 minutes, and the flash unit will then return to normal.
• When the over-temperature protection is started, < > is shown on the screen.

Number of flashes that will activate over-temperature protection:

Number of flashes that will activate over-temperature protection in high- speed sync triggering mode:

Other Protections

The system provides real-time protection to secure the device and your safety. The following lists prompts for your reference:

Technical Data

(compatible with Canon E-TTL II, Nikon i-TTL, Sony, Olympus, Panasonic,

Fujifilm,Leica, Pentax)

Flash Mode| Wireless off: M/Multi
Wireless receiver mode:TTL/M/Multi
Guide No. (1/1 step)| 87(ISO 100,in meters,with efficient reflector)

Flash Duration (t=0.1)

| Normal: 1/220s ～ 1/11760s
Color: 1/220s ～ 1/7400s
Freeze:1/2570s ～ 1/20400s
Power (1/1 step)| 600Ws
Power Output| 10 steps:1/512 ～ 1/1(with 0.1 increment each step)
Stroboscopic Flash| Provided (up to 100 times, 100Hz)
Sync Mode| High-speed sync (up to 1/8000 seconds), first-curtain sync, and second-

curtain sync

Delay Flash| 0.01 ～ 30s
Mask| √
Fan| √
Beep| √
Flash Duration Indication| √
Photocell| S1/S2/OFF
Display| Color screen
Modeling Lamp
Max. Input Power| 40W
Brightness Range| 10%-100%
CRI| Average≥97
TLCI| Average≥98
CCT| 2800K-6000K
Wireless Flash (2.4G transmission)
Wireless Function| Receiver, Off
Controllable Receiver Groups| 16: 0-9, A-F
Transmission Range| Approx. 100m
Channels| 32:1-32
ID| 01-99/OFF

Specifications and data may subject to changes without notice.

Firmware Upgrade

• This flash supports firmware upgrade through the USB-C port. Update information will be released on our official website.
• Please use an USB-C cable (sold separately) for firmware upgrade.
• As the firmware upgrade needs the support of Godox G3 software, please download and install the ‘Godox G3 firmware upgrade software” from Godox official website before upgrading. Then, choose the related firmware file.
• Please refer to the latest electronic version of the instruction manual.

Maintenance

• Shut down the device immediately should abnormal operation be detected.
• Avoid sudden impacts and the product should be dedusted regularly.
• It is normal for the flash tube to be warm when in use. Avoid continuous flashes if unnecessary.
• Maintenance of the flash must be performed by our authorized maintenance department which can provide original accessories.
• This product except consumables e.g. flash tube, is supported with a one-year warranty.
• Unauthorized service will void the warranty.
• If the product had failures or was wetted, do not use it until it is repaired by professionals.
• Changes made to the specifications or designs may not be reflected in this manual.

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.

Warning

• Operating frequency: 2412.99MHz – 2464.49MHz (only receive)

Declaration of Conformity

GODOX Photo Equipment Co.,Ltd. hereby declares that this equipment are in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. In accordance with Article 10(2) and Article 10(10), this product is allowed to be used in all EU member states.For more information of DoC, Please click this web link: https://www.godox.com/eu- declaration-of-conformity/
The device complies with RF specifications when the device used at 0mm from your body.

Warranty

Dear customers, as this warranty card is an important certificate to apply for our maintenance service, please fill in the following form in coordination with the seller and safe-keep it. Thank you!

Note: This form shall be sealed by the seller

Applicable Products

Applicable ProductsThe document applies to the products listed on the Product Maintenance Information (see below for further information). Other products or accessories (e.g. promotional items, giveaways and additional accessories attached,etc.) are not included in this warranty scope.

Warranty Period

The warranty period of products and accessories is implemented according to the relevant Product Maintenance Information. The warranty period is calculated from the day(purchase date) when the product is bought for the first time.And the purchase date is considered as the date registered on the warranty card when buying the product.

How to Get the Maintenance Service

If maintenance service is needed, you can directly contact the product distributor or authorized service institutions. You can also contact the Godox after-sale service call and we will offer you service. When applying for maintenance service, you should provide valid warranty card. If you cannot provide valid warranty card, we may offer you maintenance service once confirmed that the product or accessory is involved in the maintenance scope, but that shall not be considered as our obligation.

Inapplicable Cases

The guarantee and service offered by this document are not applicable in the following cases:

1. The product or accessory has expired its warranty period;
2. Breakage or damage caused by inappropriate usage, maintenance or preservation, such as improper packing, improper usage, improper plugging in/out external equipment, falling off or squeezing by external force, contacting or exposing to the improper temperature, solvent, acid, base, flooding and damp environments, etc;
3. Breakage or damage caused by non-authorized institution or staff in the process of installation, maintenance, alternation, addition and detachment;
4. The original identifying information of product or accessory is modified, alternated, or removed;
5. No valid warranty card;
6. Breakage or damage caused by using illegally authorized, nonstandard or non-public released software;
7. Breakage or damage caused by force majeure or accident;
8. Breakage or damage that could not be attributed to the product itself. Once met these situations above, you should seek solutions from the related responsible parties and Godox assumes no responsibility. The damage caused by parts, accessories and software that beyond the warranty period or scope is not included in our maintenance scope. The normal discoloration, abrasion and consumption are not the breakage within the maintenance scope.

Maintenance and Service Support Information

The warranty period and service types of products are implemented according to the following Product Maintenance Information:

Product Type| Name| Maintenance Period(month)| Warranty Service Type
---|---|---|---

Parts

| Circuit board| 12| The customer sends the product to the designated site
Battery| 3| The customer sends the product to the designated site
Electrical parts e.g.battery charger, etc.| 3| The customer sends the product to the designated site
Other Items| Flash tube, modeling lamp, lamp body, lamp cover, locking device, package, etc.|

No

|

Without warranty

FAQ

Frequently Asked Questions

• Which cameras are compatible with the wireless system?
  • The wireless system is compatible with Canon, Nikon, Sony, Olympus, Panasonic, Fujifilm, Pentax, Leica, etc.
• What is the maximum transmission distance for wireless flash shooting?
  • The transmission distance can reach up to 100 meters depending on conditions like positioning and environment.

Contact

Wechat Official Account

• GODOX Photo Equipment Co., Ltd.
• Add.: Building 2, Yaochuan Industrial ZoneTangwei Community, Fuhai Street, Bao’an District, Shenzhen 518103, China
• Tel: +86-755-29609320(8062)
• Tel: +86-755-29609320(8062)
• Fax: +86-755-25723423
• E-mail: godox@godox.com
• www.godox.com

Made in China | 705-AD60P2-00

Godox After-sale Service Call +86-755-29609320(8062)

Wechat Official Account

Documents / Resources

| Godox AD600 ProII All in One Outdoor Flash [pdf] Instruction Manual
AD600PROII, XPro, XProIIX2TX3, AD600 ProII All in One Outdoor Flash, AD600 ProII, All in One Outdoor Flash, Outdoor Flash, Flash
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>